mark the floor with a cross-mark. This is the center point of the wheel and tire
assembly (Figure 24).
HINT:
o The vertical laser line must line up with the line on the wheel arch, not the
wheel center cap (Figure 23).
o To ensure the wheel center mark is not covered up by the bulge in the tire,
ensure the vehicle is parked on a completely level area and the tires are
properly inflated.

Wheel
center point

Mark

Figure 24

Figure 23
21.

Repeat steps 16 - 20 starting on page 13, to mark the center point’s at all four (4)
wheel and tire assemblies.

15/71

NTB23-076B

Placing Calibration Targets for the Driver (LH) and/or Passenger (RH) Side Cameras
IMPORTANT: Steps 22 - 34 and the related figures show the driver (LH) side of the
vehicle. The passenger (RH) side is similar. If the AVM Control Module was replaced,
steps 22 - 34 must be performed for both the driver and passenger side cameras.

22.

Place the laser level approximately 1500 mm (59 in.) behind the rear wheel
(Figure 25), and then align the laser level so that the laser line is perfectly centered
through the center points of both wheel and tire assemblies marked in step 20 on
page 15.

Wheel
center point

Laser level

Figure 25

Laser line

Wheel
center point
Laser level

1500 mm

Figure 26

16/71

NTB23-076B

23.

Activate a second vertical laser line (90° to the original laser line), and then mark a
line at 500 mm and 2500 mm from the original laser line, as shown in Figure 27 and
Figure 28.

Wheel
center point
Laser level

500 mm

Laser line

2500 mm
Laser line
Figure 27

Laser level

Wheel
center point

500 mm
mark

Figure 28

17/71

NTB23-076B

24.

Repeat steps 22 - 23 starting on page 16, for the front of the vehicle.

Wheel
center point

Laser level

Laser line

500 mm

2500 mm
Laser line
Figure 29

2500 mm
mark
500 mm
mark

2500 mm
mark
500 mm
mark
Figure 30

18/71

NTB23-076B

25.

Use a chalk line tool to make a line between the 500 mm and 2500 mm marks, as
shown in Figure 31 and Figure 32.

500 mm chalk
line

2500 mm
chalk line
Figure 31

2500 mm
chalk line

500 mm chalk
line
Figure 32

19/71

NTB23-076B

26.

Place the laser level with both vertical lines activated, and align one laser line with the
500 mm chalk line and align the other laser line to the center point on the front driver
(LH) side wheel, as shown in Figure 33 and Figure 34.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

500 mm chalk
line

Laser line

2500 mm
chalk line
Figure 33

500 mm chalk
line

Wheel center
point

Figure 34

20/71

NTB23-076B

27.

Place a mark on the floor below the laser line (Figure 36).

Mark
Figure 35
28.

Figure 36

Measure and mark 1000 mm increments, as shown in Figure 37 and Figure 38.

500 mm chalk
line

1000 mm

1000 mm

1000 mm

1000 mm

2500 mm
chalk line
Figure 37

500 mm chalk
line
1000 mm

1000 mm

1000 mm

1000 mm

Figure 38
21/71

NTB23-076B

29.

Move the laser level to the position shown in Figure 39, and then make a mark on the
2500 mm chalk line.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

500 mm chalk
line

2500 mm
chalk line

Mark
Figure 39

2500 mm
chalk line

Mark
Figure 40

22/71

NTB23-076B

30.

Move the laser level to the position shown in Figure 41, and then make a mark on the
2500 mm chalk line.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

500 mm chalk
line

2500 mm
chalk line

Mark
Figure 41

2500 mm
chalk line

Mark

Figure 42

23/71

NTB23-076B

31.

Using a carpenter’s square, squared to the chalk line, extend each of the seven (7)
marks 12 in. from the chalk line.

Chalk
line

Mark
Carpenter’s
square

Figure 43

500 mm chalk
line

Extend these marks
Figure 44

24/71

NTB23-076B

32.

Place five (5) targets on the marks along the 500 mm chalk line.
IMPORTANT: Orient and align the targets, as shown in Figure 45, Figure 46 and
Figure 47. The targets must be aligned with the 500 mm chalk line and the marks
made in step 31 on page 24.

Align

Align

500 mm chalk
line

Align

Mark

Figure 45

Figure 47

Figure 46

25/71

NTB23-076B

33.

Place one (1) target on the forward most mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 48, Figure 49 and
Figure 50. The target must be aligned with the 2500 mm chalk line and the mark
made in step 31 on page 24.
Align

Mark

Align

Align

2500 mm
chalk line
Figure 48

Figure 49

Figure 50

26/71

NTB23-076B

34.

Place one (1) target on the rearward most mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 51, Figure 52 and
Figure 53. The target must be aligned with the 2500 mm chalk line and the mark
made in step 31 on page 24.
Align

Mark

Align

Align

2500 mm
chalk line
Figure 51

Figure 52
35.

Figure 53

If the passenger (RH) side camera was replaced, repeat steps 22 - 34 starting on
page 16, to place the calibration targets for the passenger (RH) side camera.

27/71

NTB23-076B

Driver (LH) Side Camera Calibration Measurements
36.

Measure the distance between the wheel center point and the center of the calibration
targets T1, T6, T7, and T5, as shown in Figure 54 below.
IMPORTANT: All measurements must be in millimeters (mm). Refer to the
illustrations in Figure 54 to ensure the correct measurement is documented in the
correct order and for each calibration target.

ARIYA

Figure 54

28/71

NTB23-076B

37.

Place the laser level on a clean cloth, and then on the roof of the vehicle.
IMPORTANT:
o Place the laser level in the middle of the vehicle’s roof.
o The laser level must be still (no fans should be blowing).

Figure 56

Figure 55

IMPORTANT: For steps 38 and 39:

38.



When holding the carpenter’s wooden folding ruler (carpenter’s ruler), ensure the
ruler is completely upright and does not bend.



All measurements must be in millimeters (mm).



Refer to the illustrations in Figure 59 on page 30 to ensure the correct
measurement is documented in the correct order and for each calibration target.

Using a folding carpenter’s ruler, measure the height from the center of each
calibration target, and then record the measurements H1-H7 in the table in Figure 59
on page 30.

Figure 57
39.

Figure 58

Using a folding carpenter’s ruler, measure the height from the wheel center point, and
then record the measurements H8-H11 in the table in Figure 59 on page 30.

29/71

NTB23-076B

ARIYA

Figure 59

30/71

NTB23-076B

Passenger (RH) Side Camera Calibration Measurements
40.

Measure the distance between the wheel center point and the center of the calibration
targets T1, T6, T7, and T5, as shown in Figure 60 below.
IMPORTANT: All measurements must be in millimeters (mm). Refer to the
illustrations in Figure 60 to ensure the correct measurement is documented in the
correct order and for each calibration target.

ARIYA

Figure 60

31/71

NTB23-076B

41.

Refer to steps 37 - 39 on page 29 to set up the laser level to measure the height of
the passenger (RH) side camera, and then document the measurements in Figure 61.
IMPORTANT: All measurements must be in millimeters (mm). Refer to the
illustrations in Figure 61 to ensure the correct measurement is documented in the
correct order and for each calibration target.

ARIYA

Figure 61

32/71

NTB23-076B

Marking the Center Point for the Front of the Vehicle
42.

Place the laser level approximately 800 mm (31.5 in.) from the front of the vehicle and
align the laser with the front camera, as shown in Figure 63.
IMPORTANT: Be sure to center the laser line with the front camera and not the
“NISSAN” brand name on the emblem.