Continue to press the brake pedal as you normally would, and do not "pump" (repeatedly press and release) the
pedal as this will interrupt the function.
This alert will clear when your vehicle comes to a stop or you are no longer pressing the brake pedal. It may still be
displayed for up to 5 seconds afterward.

339

Owners Manual
Reduced braking performance is usually temporary, and can occur for a number of reasons including high brake
temperatures after heavy brake use, or driving in extremely cold or wet conditions. It can also indicate that your
brake pads or rotors have worn to the point that normal replacement is needed.
If you continue to experience reduced braking performance which does not improve over time, please contact Tesla
service at your convenience for a brake inspection.
For more information, see Hydraulic Fade Compensation on page 116.
GTW_w405
Electrical system power reduced
Vehicle may shut down unexpectedly
What this alert means:
The electrical system cannot maintain the voltage required to support all vehicle features.
If this alert is present while you are driving, it is possible your vehicle will shut down unexpectedly.
It is also possible that your vehicle will not restart after the current drive.
What to do:
It is recommended that you eliminate or reduce your use of any non-essential features. This can help your vehicle
maintain adequate electrical power for essential functions. It may also prevent your vehicle from shutting down
before you reach your immediate destination, although this is not guaranteed.
If this alert remains active, schedule service immediately. Without service, your vehicle may shut down unexpectedly
or may not restart.
MCU_u005
Front trunk open
Proceed with caution
What this alert means:
Your vehicle's front trunk (hood) is detected open while driving.
This alert indicates at least one of the two latches securing the hood, the front trunk primary and/or secondary latch,
cannot be confirmed closed (confirmed as fully secured) when your vehicle is shifted into a gear other than Park.
What to do:
As this condition may lead to the front trunk opening while driving, it is recommended that you drive carefully until
you can safely bring your vehicle to a stop and shift into Park.
Once your vehicle is parked, check the front trunk (hood) to make sure it is fully closed (both latches are fully
engaged). For more information, see Closing instructions for the Front Trunk on page 42.
The alert should clear once your vehicle is shifted into Park. However, it may return once you start driving if you do
not first inspect and fully secure the hood.
If this alert persists across multiple drives, or occurs with increasing frequency over several drives, it is recommended
that you schedule service at your earliest convenience.
For more information on the front trunk, see Front Trunk on page 42.
MCU_u019
Active service connection to vehicle
Service performing remote diagnostics
What this alert means:
A service technician is remotely logged into your vehicle for diagnosis or repair. You may notice some loss of
Infotainment functionality while the connection persists, but this alert does not indicate an issue with your vehicle.
340

Owners Manual
Your vehicle is OK to drive.
What to do:
This alert should clear automatically after the technician completes vehicle diagnosis or repair. You may find it
necessary to restart your touchscreen to restore full Infotainment functionality after the alert has cleared.For more
information, see Restarting the Touchscreen in your vehicle's Do It Yourself Guide.
If this alert does not clear after 24 hours, it is recommended that you schedule service via your Tesla Mobile App or
with an independent service provider. Please note that independent service provider options may vary, based on
your vehicle configuration and your location.
MCU_w008
Air pressure in tires very low
PULL OVER SAFELY - Check for flat tire
What this alert means:
This alert indicates that one or more of the tires on your vehicle is extremely low or flat.
The tire pressure monitoring system (TPMS) has detected that the air pressure in one or more of your tires is
significantly lower than the recommended cold tire pressure.
What to do:
You should pull over carefully as soon as possible. In a safe location, check for a flat tire.
You can request Tesla roadside assistance options (mobile tire, loaner wheel, tow) if required. See Contacting Tesla
Roadside Assistance on page 304 for more information.
In a non-emergency situation, it is recommended that you visit a local tire shop for assistance or schedule service
using your Tesla Mobile App.
See Maintaining Tire Pressures on page 257 for detailed information on where to find the recommended cold
pressure (RCP) for your vehicle's tires, how to check tire pressures, and how to keep your tires properly inflated.
The alert will clear once the TPMS has a consistent tire pressure measurement for each of your tires within 3 psi of
the recommended cold pressure.
• The alert and Tire Pressure indicator light may still be present immediately after you have filled your tires to the
recommended cold pressure, but both should clear once you have driven a short distance.
• You may need to drive over 15 mph (25 km/h) for at least 10 minutes for the Tire Pressure Monitoring System to
measure and report your updated tire pressures.
For more information on tire pressure and inflation, see Tire Care and Maintenance on page 257.
MCU_w010
Air pressure below recommendation for tires
Check pressure and refill air as needed
What this alert means:
This alert does NOT indicate that there is a flat tire.
The tire pressure monitoring system (TPMS) has detected that the air pressure in one or more of your tires is at least
20% lower than the recommended cold tire pressure.
See Maintaining Tire Pressures on page 257 for detailed information on where to find the recommended cold
pressure (RCP) for your vehicle's tires, how to check tire pressures, and how to keep your tires properly inflated.
This alert may appear in cold weather because the air in your tires naturally contracts when it becomes cold,
decreasing tire pressures.
What to do:
341

Owners Manual
Add air to maintain the recommended cold tire pressure. Although drops in tire pressure are expected in colder
weather, the recommended cold tire pressure should be maintained at all times.
The alert may clear as the vehicle is driven. This is because the tires will warm up and the tire pressure will increase.
Even if the alert clears, the tires should still be refilled with air once they have cooled.
The alert will clear once the Tire Pressure Monitoring System detects that each of your tires is inflated to the
recommended cold pressure.
• The alert and Tire Pressure indicator light may still be present immediately after you have filled your tires to the
recommended cold pressure, but both should clear once you have driven a short distance.
• You may need to drive over 15 mph (25 km/h) for at least 10 minutes for the Tire Pressure Monitoring System to
measure and report your updated tire pressures.
If you repeatedly see this alert for the same tire, have the tire inspected for a slow leak. You can visit a local tire shop
or schedule service using your Tesla Mobile App.
For more information on tire pressure and inflation, see Tire Care and Maintenance on page 257.
For more information on tire pressure and inflation, see Tire Care and Maintenance on page 257.
MCU_w029
Service is required
Schedule service now
What this alert means:
This alert is set remotely by Tesla when a condition requiring service is detected on your vehicle.
This alert can be set due to various conditions. When you schedule service, more information should be available.
This alert can only be cleared by a service technician after your vehicle has been serviced.
What to do:
As this alert can be present due to various conditions, it is recommended that you schedule service at your earliest
convenience.
TAS_a313
Adaptive ride control degraded
Ride comfort may be reduced
What this alert means:
There is an issue with your vehicle’s Adaptive Suspension Damping system. As a result, the system cannot provide
real-time adjustments to the suspension system to optimize both ride and handling.
Instead, all dampers are receiving fixed current. Your ride may be softer or firmer than usual.
What to do:
If this alert persists throughout subsequent drives, schedule service at your earliest convenience. Your vehicle is OK
to drive in the meantime.
This alert is accompanied by a yellow indicator light on the instrument panel. For more information, see Air
Suspension on page 120.
TAS_a314
Adaptive ride control degraded
Drive with caution
What this alert means:

342

Owners Manual
There is an issue with your vehicle’s Adaptive Suspension Damping system. As a result, the system cannot provide
real-time adjustments to the suspension system to optimize both ride and handling, and your ride may be softer
than usual.
What to do:
If this alert persists throughout subsequent drives, schedule service at your earliest convenience. Your vehicle is OK
to drive in the meantime.
This alert is accompanied by a red indicator light on the instrument panel. For more information, see Air Suspension
on page 120.
THC_u0005
Air conditioning temporarily reduced
Vehicle systems being cooled
What this alert means:
Cabin air conditioning performance has been temporarily reduced because your vehicle needs to focus on cooling
the high voltage battery (Battery) and/or powertrain. This is completely normal and does not indicate a problem
with your vehicle or the air conditioning (A/C) system.
In addition to cooling the vehicle interior, the A/C system also cools the Battery. The A/C system’s priority is to cool
the Battery to make sure it stays within an optimal temperature range that supports longevity and best performance.
In high temperature environments, it is normal for your vehicle to focus more for brief periods on cooling the Battery.
When this happens, it is most often because the vehicle is supercharging in hot weather.
What to do:
No action is required. Your vehicle is OK to drive.
The alert should clear in a short time, and cabin air conditioning performance should return to normal. In some cases,
the alert and vehicle behavior will continue until supercharging is complete.
If the alert persists over multiple drives and is accompanied by other alerts that indicate potential issues with the
A/C system, contact Tesla Service at your convenience to schedule an A/C system inspection.
THC_w0100
Battery heating unavailable - Charge rate reduced
Charging may be unavailable in cold temperatures
What this alert means:
A condition affecting the performance of your vehicle's high voltage battery heater has been detected.
Without adequate heating of the high voltage battery, charging speed (charge rate) may be reduced. Your vehicle
may also be unable to charge in cold ambient temperatures (cold weather) while high voltage battery heating
remains unavailable.
What to do:
Your vehicle is OK to drive. Your vehicle is also OK to charge and connect to a charging station. However, your
vehicle may be unable to charge, or may charge more slowly than expected, in cold ambient temperatures.
If possible, try charging your vehicle in a closed environment like a garage, where warmer ambient temperatures
may make high voltage battery heating unnecessary.
If driving in cold ambient temperatures, it is recommended that you do NOT rely on charging stations along your
route to reach your destination, as the high voltage battery may be too cold to charge.
• If you need to charge, try to charge your vehicle immediately after a drive. The high voltage battery may still be
warm from the previous drive.

343

Owners Manual
• Leaving your vehicle parked in cold ambient temperatures after a drive will cause the high voltage battery to
cool, and charging may become unavailable.
Similarly, it is recommended that you do not rely on regenerative braking to charge the high voltage battery while
driving in cold ambient temperatures, as regenerative braking may be unavailable if the battery temperature is too
low. For more information, see Regenerative Braking on page 116.
This alert may be present due to many conditions. It may be caused by a temporary condition that requires no action
to resolve.
However, if this alert persists over multiple drives, or is accompanied by other alerts indicating potential issues with
your vehicle's heating and/or air conditioning system, it is recommended that you schedule service at your earliest
reasonable opportunity.
For more information on charging, see Charging Instructions on page 241.
For more information on the high voltage battery, see High Voltage Battery Information on page 239.
UMC_w001
Unable to charge with Mobile Connector
Inadequate outlet grounding - Try another outlet
What this alert means:
The Mobile Connector has detected that the electrical outlet has insufficient grounding, likely caused by an
inadequate or missing ground connection.
This does not indicate an issue with your Mobile Connector or vehicle, but instead points to an issue with the wall
outlet / electrical installation the Mobile Connector is connected to.
What to do:
Have the electrical installation inspected by an electrician. Your electrician should make sure there is proper
grounding at your circuit breaker or power distribution box, and also make sure that appropriate connections are
made to the outlet, before you attempt to plug in the Mobile Connector again.
If you need to charge in the meantime, try charging using a different outlet, at another location, or with another type
of charging station.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w002
Unable to charge - Mobile Connector GFCI tripped
Unplug charge handle from charge port and retry
What this alert means:
The vehicle cannot charge because the ground-fault circuit interrupter (GFCI) in the Mobile Connector has tripped.
Like the GFCI in a wall outlet, this feature is designed to stop the flow of electricity when there is a problem. It has
interrupted charging to protect your vehicle and the charging equipment.
This could happen for many reasons. The problem could be in the charge cable, the charge handle, the charge port,
or even an onboard vehicle component.
What to do:
Inspect the charge port and the charge handle for pooled water or unusual levels of moisture. If you find excessive
moisture, wait and let both the inside area of the charge port and the exposed portion of the charge handle dry
sufficiently before trying again.
344

Owners Manual
Inspect the charge equipment for damage.
• If the cable is in any way damaged or deteriorated, do not use it. Try different charging equipment instead.
• If the cable is in good condition, try charging again with the same Mobile Connector.
If the issue persists and prevents charging, try charging with different charging equipment.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w004
Unable to charge with Mobile Connector
Voltage too high / Try a different wall outlet
What this alert means:
The vehicle cannot charge, or charging is interrupted, because either the Mobile Connector:
• Detects the wall outlet voltage is too high, or
• Detects an unexpected increase in supply voltage from the wall outlet.
What to do:
Try charging the vehicle with a different wall outlet. If the vehicle starts to charge, the issue was likely with the
original wall outlet. Contact an electrician to inspect the building wiring connection to that outlet.
If the vehicle still does not charge when you try a different wall outlet, try charging at a different location.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w005
Unable to charge with Mobile Connector
Voltage too low / Try a different wall outlet
What this alert means:
The vehicle cannot charge, or charging is interrupted, because either the Mobile Connector:
• Does not detect enough supply voltage from the wall outlet, or
• Detects an unexpected drop in supply voltage from the wall outlet.
What to do:
Try charging the vehicle with a different wall outlet. If the vehicle starts to charge, the issue was likely with the
original wall outlet. Contact an electrician to inspect the building wiring connection to that outlet.
If the vehicle still does not charge when you try a different wall outlet, try charging at a different location.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.

345

Owners Manual
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w007
Mobile Connector control box temperature high
Let Mobile Connector cool to resume charging
What this alert means:
Charging has been interrupted because the Mobile Connector has detected a high temperature inside its control box
housing.
What to do:
Make sure the Mobile Connector is not covered by anything, and that there is no heat source nearby. If the problem
persists in normal ambient temperatures (under 100°F or 38°C), service is required.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w008
Unable to charge - Wall plug temperature high
Wall outlet and wiring inspection recommended
What this alert means:
High temperature detected by Mobile Connector alerts indicate the outlet used to charge is becoming too warm, so
charging has stopped to protect the outlet.
This does not indicate an issue with your Mobile Connector or vehicle, but instead points to an issue with the wall
outlet / electrical installation the Mobile Connector is connected to.
A warm outlet may be caused by a plug that is not fully inserted, a loose building wiring connection to the outlet, or
an outlet that is beginning to wear out.
What to do:
Make sure your adapter is fully plugged into the outlet. If charging speed does not return to normal, contact an
electrician to inspect the outlet and building wiring connections to the outlet and complete any repairs needed.
If the outlet is worn, it should be replaced with a high-quality outlet. Consider upgrading to a Tesla Wall Connector
for greater convenience and highest charging speed.
UMC_w009
Cannot charge - Charge handle temperature high
Check charge handle or charge port for debris
What this alert means:
Charging has been interrupted because the Mobile Connector has detected a high temperature in the charge handle
that connects to your vehicle's charge port.
What to do:
Make sure the Mobile Connector is fully inserted into your vehicle's charge port inlet.

346

Owners Manual
Inspect the charge port inlet and the Mobile Connector handle for any obstructions or moisture. Make sure any
obstruction in the charge port or Mobile Connector handle has been removed and any moisture has been allowed to
dry, then try re-inserting the Mobile Connector handle into the charge port.
Also make sure the charge handle of the Mobile Connector is not covered by anything, and that there is no heat
source nearby.
If the alert persists in normal ambient temperatures (under 100°F or 38°C), and occurs during multiple charging
attempts, this may indicate a condition affecting the Mobile Connector or your vehicle. It is recommended that you
schedule service at your convenience.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w010
Mobile Connector to adapter connection hot
Let cool - Plug adapter fully into Mobile Connector
What this alert means:
Charging has been interrupted because the Mobile Connector has detected a high temperature at the connection
between the wall plug adapter and the control box.
What to do:
Make sure the wall plug adapter is fully connected to the Mobile Connector control box.
Also make sure the wall plug adapter is not covered by anything, and that there is no heat source nearby.
After unplugging from the power source (wall outlet), inspect the wall plug adapter connection and the Mobile
Connector control box connection for any obstructions or moisture. Make sure any obstruction has been removed
and any moisture has been allowed to dry, then try re-inserting the wall plug adapter into the Mobile Connector and
then connecting to the power source (wall outlet).
Once the Mobile Connector control box temperature has decreased and any obstruction has been removed, the alert
should clear and charging should possible.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w011
Charging equipment communication error
Try again or try different equipment
What this alert means:
Your vehicle is unable to charge because it cannot communicate effectively with the Mobile Connector. The Mobile
Connector cannot confirm via proximity detection that the charge handle is fully connected to your vehicle.
What to do:
First, confirm the lack of effective communication is caused by the Mobile Connector rather than an issue with your
vehicle. This is usually the case.
To confirm this, try charging the vehicle using different external charging equipment.
• If the vehicle begins charging, the issue was likely with the Mobile Connector.
347

Owners Manual
• If the vehicle still does not charge, the issue may be with the vehicle.
Inspect the charge port inlet and the Mobile Connector handle for any obstructions (use a flashlight as necessary).
Make sure any obstruction has been removed and any moisture has been allowed to dry, then try re-inserting the
Mobile Connector handle into the charge port.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
For more information on charging, see Charging Instructions on page 241.
UMC_w012
Charging equipment communication error
Try again or try different equipment
What this alert means:
Your vehicle is unable to charge because it cannot communicate effectively with the Mobile Connector. The Mobile
Connector detects that it cannot generate or maintain a valid control pilot signal.
What to do:
First, confirm the lack of effective communication is caused by the Mobile Connector rather than an issue with your
vehicle. This is usually the case.
To confirm this, try charging the vehicle using different external charging equipment.
• If the vehicle begins charging, the issue was likely with the Mobile Connector.
• If the vehicle still does not charge, the issue may be with the vehicle.
Inspect the charge port inlet and the Mobile Connector handle for any obstructions (use a flashlight as necessary).
Make sure any obstruction has been removed and any moisture has been allowed to dry, then try re-inserting the
Mobile Connector handle into the charge port.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
For more information on charging, see Charging Instructions on page 241.
UMC_w013
Wall plug adapter error - Charge rate reduced
Plug adapter fully into Mobile Connector and retry
What this alert means:
Your Mobile Connector is unable to communicate with the wall plug adapter. Because your Mobile Connector cannot
monitor the wall plug adapter temperature, charge current is automatically reduced to 8A.
What to do:

348

Owners Manual
1. Unplug your Mobile Connector, including the wall plug adapter, completely from the wall outlet.
2. Make sure the connection between the wall plug adapter and the main body of your Mobile Connector is secure.
a. Disconnect the wall plug adapter completely from the main body of your Mobile Connector.
b. Fully reinsert the wall plug adapter into the main body of your Mobile Connector by pushing it into the socket
until it snaps into place.
3. Try charging again by plugging the Mobile Connector, including wall plug adapter, fully into the wall outlet.
4. If the alert persists, try using a different wall plug adapter (see steps above to make sure the adapter is fully
connected to your Mobile Connector).
a. If the alert is no longer present, the issue is likely with the wall plug adapter you were using previously.
b. If the alert persists, the issue is likely with your Mobile Connector.
If needed, obtain another wall plug adapter or Mobile Connector.
In the meantime, you can continue to charge with the same equipment. The charge rate will be reduced, as charge
current will be limited to 8A while this condition persists.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w014
Wall plug adapter error - Charge rate reduced
Plug adapter fully into Mobile Connector and retry
What this alert means:
Your Mobile Connector is unable to communicate with the wall plug adapter. Because your Mobile Connector cannot
identify the type of wall outlet the wall plug adapter is connected to, charge current is automatically reduced to 8A.
What to do:
1. Unplug your Mobile Connector, including the wall plug adapter, completely from the wall outlet.
2. Make sure the connection between the wall plug adapter and the main body of your Mobile Connector is secure.
a. Disconnect the wall plug adapter completely from the main body of your Mobile Connector.
b. Fully reinsert the wall plug adapter into the main body of your Mobile Connector by pushing it into the socket
until it snaps into place.
3. Try charging again by plugging the Mobile Connector, including wall plug adapter, fully into the wall outlet.
4. If the alert persists, try using a different wall plug adapter (see steps above to make sure the adapter is fully
connected to your Mobile Connector).
a. If the alert is no longer present, the issue is likely with the wall plug adapter you were using previously.
b. If the alert persists, the issue is likely with your Mobile Connector.
If needed, obtain another wall plug adapter or Mobile Connector. In the meantime, you can continue to charge with
the same equipment. The charge rate will be reduced, as charge current will be limited to 8A while this condition
persists.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.

349

Owners Manual
UMC_w015
Wall plug adapter error - Charge rate reduced
Plug adapter fully into Mobile Connector and retry
What this alert means:
Your Mobile Connector is unable to communicate with the wall plug adapter. Because your Mobile Connector cannot
identify the type of wall outlet the wall plug adapter is connected to, charge current is automatically reduced to 8A.
What to do:
1. Unplug your Mobile Connector, including the wall plug adapter, completely from the wall outlet.
2. Make sure the connection between the wall plug adapter and the main body of your Mobile Connector is secure.
a. Disconnect the wall plug adapter completely from the main body of your Mobile Connector.
b. Fully reinsert the wall plug adapter into the main body of your Mobile Connector by pushing it into the socket
until it snaps into place.
3. Try charging again by plugging the Mobile Connector, including wall plug adapter, fully into the wall outlet.
4. If the alert persists, try using a different wall plug adapter (see steps above to make sure the adapter is fully
connected to your Mobile Connector).
a. If the alert is no longer present, the issue is likely with the wall plug adapter you were using previously.
b. If the alert persists, the issue is likely with your Mobile Connector.
If needed, obtain another wall plug adapter or Mobile Connector. In the meantime, you can continue to charge with
the same equipment. The charge rate will be reduced, as charge current will be limited to 8A while this condition
persists.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w016
Mobile Connector control box temperature high
Maximum charge rate reduced
What this alert means:
Charge current has been temporarily reduced because the Mobile Connector has detected increased temperature
inside its control box housing.
What to do:
Make sure the Mobile Connector is not covered by anything, and that there is no heat source nearby. If the problem
persists in normal ambient temperatures (under 100°F or 38°C), service is required.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w017
Charge rate reduced - Wall plug temperature high
Wall outlet and wiring inspection recommended
What this alert means:

350

Owners Manual
High temperature detected by Mobile Connector alerts indicate the outlet used to charge is becoming too warm, so
charging has been slowed to protect the outlet.
This is not typically an issue with your vehicle or your Mobile Connector, but rather an issue with the outlet. A warm
outlet may be caused by a plug that is not fully inserted, a loose building wiring connection to the outlet, or an
outlet that is beginning to wear out.
What to do:
Make sure your adapter is fully plugged into the outlet. If charging speed does not return to normal, contact an
electrician to inspect the outlet and building wiring connections to the outlet and complete any repairs needed.
If the outlet is worn, it should be replaced with a high-quality outlet. Consider upgrading to a Tesla Wall Connector
for greater convenience and highest charging speed.
UMC_w018
Charge rate reduced - Handle temperature high
Check charge handle or charge port for debris
What this alert means:
Charge current has been temporarily reduced because the Mobile Connector has detected increased temperature in
the charge handle that connects to your vehicle's charge port.
What to do:
Make sure the Mobile Connector is fully inserted into your vehicle's charge port inlet.
Inspect the charge port inlet and the Mobile Connector handle for any obstructions or moisture. Make sure any
obstruction in the charge port or Mobile Connector handle has been removed and any moisture has been allowed to
dry, then try re-inserting the Mobile Connector handle into the charge port.
Also make sure the charge handle of the Mobile Connector is not covered by anything, and that there is no heat
source nearby.
If the alert persists in normal ambient temperatures (under 100°F or 38°C), and occurs during multiple charging
attempts, this may indicate a condition affecting the Mobile Connector or your vehicle. It is recommended that you
schedule service at your convenience.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.
UMC_w019
Mobile Connector to adapter connection hot
Maximum charge rate reduced
What this alert means:
Charge current has been reduced because the Mobile Connector has detected a high temperature at the connection
between the wall plug adapter and the control box.
What to do:
Make sure the wall plug adapter is fully connected to the Mobile Connector control box.
After unplugging from the power source (wall outlet), inspect the wall plug adapter connection and the Mobile
Connector control box connection for any obstructions or moisture.
It is recommended that any debris / foreign objects be removed. Make sure any obstruction has been removed and
any moisture has been allowed to dry, then try re-inserting the wall plug adapter into the Mobile Connector and then
connecting to the power source (wall outlet).
351

Owners Manual
Also make sure the wall plug adapter is not covered by anything, and that there is no heat source nearby. If the alert
persists in normal ambient temperatures (under 100°F or 38°C), and occurs during multiple charging attempts, this
may indicate a condition affecting the Mobile Connector or your vehicle. It is recommended that you schedule
service at your convenience.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 225 for more
details.
For more information on troubleshooting Mobile Connector status lights and charging issues, refer to the product's
owner's manual.

Consumer Information

352

Owners Manual
About this Owner Information
Document Applicability
For the latest and greatest information that is customized to your vehicle, view the Owner’s Manual on your vehicle’s
touchscreen by touching Controls > Service > Owner's Manual. The information is specific to your vehicle depending
on the features you purchased, vehicle configuration, market region and software version. In contrast, owner
information that is provided by Tesla elsewhere is updated as necessary and may not contain information unique to
your vehicle.
Information about new features is displayed on the touchscreen after a software update, and can be viewed at any
time by touching Controls > Software > Release Notes. If the content in the Owner's Manual on how to use your
vehicle conflicts with information in the Release Notes, the Release Notes take precedence.
Illustrations
The illustrations provided in this document are for demonstration purposes only. Depending on vehicle options,
software version and market region, the information displayed on the touchscreen in your vehicle may appear
slightly different.