Owner's Manual

Driving
WARNING: Your Cybertruck may display an alert if the road is too steep to safely park, or if the parking brakes
are not properly engaged. These alerts are for guidance purposes only and are not a substitute for the driver’s
judgment of safe parking conditions, including specific road or weather conditions. Do not depend on these
alerts to determine whether or not it is safe to park at any location. You are always responsible for parking
safely.

Brake Wear
Cybertruck brake pads are equipped with wear indicators. A wear indicator is a thin metal strip attached to the
brake pad that squeals as it rubs against the rotor when the pad wears down. This squealing sound indicates that the
brake pads have reached the end of their service life and require replacement.
Brakes must be periodically inspected visually by removing the tire and wheel. For detailed specifications and
service limits for rotors and brake pads, see Subsystems on page 248. Additionally, Tesla recommends cleaning and
lubricating the brake calipers every year or 12,500 miles (20,000 km) if in an area where roads are salted during
winter months.
WARNING: Neglecting to replace worn brake pads damages the braking system and can result in a braking
hazard.

Owner's Manual

118

Driving
Traction Control
How It Works
The traction control system constantly monitors the speed of the front and rear wheels. If Cybertruck experiences a
loss of traction, your vehicle minimizes wheel spin by controlling brake pressure and motor power. By default, the
traction control system is on. Under normal conditions, it should remain on to ensure maximum safety.
NOTE: When Cybertruck is in an Off-Road Drive Mode, the traction control system may be disabled or operate
differently. For more information about customizing the traction control system while driving off road, see Off-Road
Modes on page 122.
This yellow indicator flashes on the touchscreen whenever the traction control system is actively
controlling brake pressure and motor power to minimize wheel spin. If the indicator stays on, a fault is
detected with the traction control system. Use the mobile app to schedule a service appointment.

WARNING: Traction control cannot prevent collisions caused by driving dangerously or turning too sharply at
high speeds.

119

Owner's Manual

Driving
Ride & Handling
Cybertruck is equipped with Adaptive Air Suspension that offers superior ride quality and balances comfort with
range and performance. When carrying loads, the system also maintains a level height between the front and rear
axles.
You can manually adjust the ride height to suit your circumstances. For example, you can raise Cybertruck when you
need extra ground clearance (such as when driving on a steep driveway or ramp, in deep snow, over large speed
bumps, parking curbs, etc.) or temporarily lower Cybertruck when you need extra space above the vehicle (such as
in a parking garage).
NOTE: When Cybertruck starts, you may hear the sound of the compressor as the air suspension system’s reservoir
fills with air.
CAUTION: Before adjusting the ride height, ensure Cybertruck is clear of all obstacles, above and below.
You can adjust the ride height by touching Controls. The available ride height settings depend on your driving speed
and other conditions, such as the current drive mode. You can also adjust the ride height by touching Ride Height on
the overhead view of Cybertruck in the vehicle status area of the touchscreen when Cybertruck is parked.
NOTE: When you change the ride height from Controls, it will automatically lower or raise to the preferred ride
height again once your driving speed exceeds 25 mph (40 km/h).
If a fault is detected that reduces the performance of the adaptive air suspension system, a yellow
indicator lights up on the touchscreen. If the problem persists, use the mobile app to schedule a service
appointment.

If a fault is detected that disables the Adaptive Air Suspension system, a red indicator lights up on the
touchscreen. Use the mobile app to schedule a service appointment.

Ride Height Settings - On-Road Mode
The following ride height settings are meant for day-to-day driving when Cybertruck is in On-Road Mode. For more
information on customizing the preferred ride height, see On-Road Modes on page 121.
NOTE: Each ride height is shown in relation to Medium, which is considered to be 0 in. (0 mm).
When Easy Entry/Exit is associated with a driver profile, Cybertruck lowers to Entry setting upon entry (or exit).
Ride Height Level

Description

High

2.4 in. (6 cm) above Medium

When the ride height is set to High, it automatically returns to the
preferred ride height* after driving approximately 100 ft. (30 meters)
or when your driving speed reaches 25 mph (40 km/h).

Low

1.6 in. (4 cm) below Medium

When the ride height is set to Low, it automatically returns to the
preferred ride height* after driving approximately 100 ft. (30 meters)
or when your driving speed reaches 25 mph (40 km/h).

Entry

2.2 in. (5.5 cm) below Medium When the ride height is set to Entry, it automatically returns to the
preferred ride height* once your driving speed exceeds 10 mph (16
km/h).

* To change the Preferred Ride Height, touch Controls > Dynamics > On-Road Modes. For more information, see
On-Road Modes on page 121.

Owner's Manual

120

Driving
Ride Height Settings - Off-Road Mode
The following ride height settings are available when Cybertruck is in Off-Road Mode. For more information about
driving off-road, see Off-Road Modes on page 122.
Ride
Height

Level

Description

Extract

5.9 in. (15 cm)
above Medium

Extract is the maximum ride height, designed for use when Cybertruck is stuck on
an underbody obstacle. This is only available in certain off-road modes. When the
ride height is set to Extract, vehicle speed is limited to 10 mph (16 km/h), and
torque may be limited. The ride height automatically resets to Very High once your
driving speed exceeds 10 mph (16 km/h).

Very High 3.9 in. (10 cm)
above Medium

Very High increases ground clearance and improves approach, breakover, and
departure angles while off-road driving.When the ride height is set to Very High,
vehicle speed is limited to 25 mph (40 km/h). The ride height automatically resets
to High when your driving speed exceeds 25 mph (40 km/h).

High

High increases ground clearance to suit general off-road driving at both low and
high speeds.

2.4 in. (6 cm)
above Medium

Auto Lower
To make it easier to get into Cybertruck, enable Auto Lower (Controls > Dynamics > Auto Lower). Once enabled,
your vehicle automatically adjusts to the Entry ride height whenever your vehicle shifts into Park.
The suspension automatically raises back to your preferred ride height when you resume driving.
CAUTION: When Auto Lower is enabled and you are parking Cybertruck, ensure that there are no obstacles
underneath the vehicle that may contact the underbody when the suspension lowers.
NOTE: Auto Lower Mode is not available while in Off-Road Mode.

Self-Leveling
To prevent damage when jacking or lifting the vehicle, you must activate Jack Mode to disable self-leveling (press
the brake pedal and touch Controls > Service > Jack Mode). For more details, see Jack Mode on page 230.

Auto-Raising Locations
Whenever you raise the suspension, your vehicle saves the suspension setting based on the location. By saving the
location, you do not need to manually raise the suspension every time you arrive at a frequently-used location where
you have previously raised the suspension. When you return to the saved location, Cybertruck raises or lowers the
suspension and the touchscreen displays a message indicating that the suspension is adjusting.
When returning to a saved location and driving faster than the suspension settings allow, the suspension does not
adjust until the vehicle slows down. If Cybertruck reaches a saved location and the existing suspension setting is
already higher than the level that has been saved for that location, the ride height is not adjusted. After leaving a
saved location, the suspension automatically lowers. However, it may not lower until your vehicle meets the speed
and distance threshold at which the suspension lowers.
To remove an auto-raising location
If you do not want the suspension to automatically raise at a location, touch to deselect Always raise at this location
in the popup that appears when you arrive at a saved location.

On-Road Modes
To choose how Cybertruck accelerates and handles for day-to-day driving on public roads, touch Controls >
Dynamics > On-Road.

121

Owner's Manual

Driving
Choose between three On-Road Modes. Comfort and Sport automatically set the Acceleration, Ride & Handling, and
Preferred Ride Height to balance ride comfort, handling, and range. Custom allows you to customize these options
as you see fit.
To access additional performance and acceleration, select Beast (if equipped) and follow the on-screen prompts.
In addition, you can choose to enable Auto Shift out of Park (see Shifting on page 96) or Auto Lower (see Ride &
Handling on page 120).

Customization Options
Setting

Options

Description

Acceleration

Chill

Limits acceleration for a smooth and gentle ride. When Chill is selected, Chill displays on the
touchscreen above the driving speed.

Standard Provides the normal level of acceleration.
Ride & Handling

Preferred Ride
Height

Relaxed

Prioritizes comfort over dynamic handling response. Cybertruck will feel smoother and more
comfortable, especially on rough or uneven roads.

Focused

Provides higher damping for more dynamic driving. Cybertruck will feel more responsive and
connected to the road.

Lower

Sets the Preferred Ride Height to Lower. The ride height remains at Low on and off the
highway by default, optimizing handling and range (see Ride & Handling on page 120).

Higher

Sets the Preferred Ride Height to Higher. When set to Higher, the ride height automatically
adjusts between Medium and Low to balance ride comfort with handling and range. On
highways or while driving at highway speeds, ride height adjusts to Low (see Ride & Handling
on page 120).

Off-Road Modes
Off-road driving is driving your vehicle on an unpaved surface such as sand, silt, dirt, or mud, or on rocky or snowcovered surfaces. When Cybertruck is in an Off-Road Mode, you have access to settings and drive modes that allow
you to more easily manage steep ascents, descents, uneven terrain, shallow creeks, and other obstacles you may
encounter.
Off-Road Mode gives you greater control over traction, stability, acceleration, and braking. Off-Road Mode also
allows you to quickly adjust the ride height of Cybertruck (see Ride & Handling on page 120).
CAUTION: Carefully read all cautions and warnings before driving Cybertruck off road (see Limitations and
Warnings on page 126). Always pay close attention and monitor the area to the front, rear, and sides of
Cybertruck for obstacles while off-road driving.
CAUTION: Any damage caused by off-road driving is not covered by the warranty.

Before Off-Road Driving
1. Plan your route: Carefully consult maps and weather reports before beginning an off-road expedition and
familiarize yourself with the different types of terrain you may encounter (gravel, sand, mud, snow, etc.). Research
trails before setting out and be aware that weather and environmental conditions can change quickly and
unexpectedly. Ensure your vehicle has ample range for your planned route.
2. Secure passengers and cargo: Wearing a seat belt is required by law. Ensure that all passengers are wearing their
seat belts properly (see Seat Belts on page 47). Make sure that loose items in the cabin are stowed or secured,
and ensure that the cargo bed is free of cargo, or that cargo is tightly secured. The tonneau cover can be open or
closed while driving off road.
3. Evenly distribute vehicle load: While off-road driving, Cybertruck performs best when the weight of passengers
and cargo is distributed evenly across the front and rear axles (see Vehicle Loading on page 240). Detach large
or heavily loaded trailers before driving off road.
4. Lower tire pressure: Lower tire pressure to increase traction on softer surfaces such as sand or gravel, and on
rocky surfaces. Reducing tire pressure allows tires to make more contact with the terrain, increasing grip and
decreasing the risk of punctures.
Owner's Manual

122

Driving
WARNING: Avoid making hard turns and other sudden manuevers when tires are inflated under the
recommended cold tire pressure. Before driving on public roads again, make sure to fill all tires to the
recommended cold tire pressure (see Tire Pressures on page 212).
5. Be prepared: Equip your Cybertruck with supplies in case of emergency, such as a spare tire, a jack, an air
compressor, a portable jump starter, and a flashlight.
6. Remove the rocker panels: Cybertruck has two pieces of plastic trim that descend in front of the front wheels and
rear wheels, respectively, from the rocker panels on either side of the vehicle. This trim increases aerodynamic
performance and range, but may be damaged while driving off-road over rough, uneven surfaces, rocks, or
obstacles. To prevent damage, remove the rocker panels before off-road driving. For more information and
instructions for removing the rocker panels, refer to the Do It Yourself Guide (see Do It Yourself Maintenance on
page 237).
7. Remove wheel covers: To prevent damage, remove the wheel covers before driving off-road. For more
information, see Removing and Installing Wheel Covers on page 218.

Enabling Off-Road Mode
To enable Off-Road Mode:
1. Touch Controls > Dynamics > Off-Road.
2. After carefully reading and understanding the popup window, touch Yes.
WARNING: Only use Off-Road Mode in off-road driving scenarios. Off-Road Mode changes how Cybertruck
handles, accelerates and decelerates, and is not appropriate for public roads.
Cybertruck has two Off-Road Modes.
• Overland: Maximizes traction on all terrains at low speeds. See Overland on page 123.
• Baja: Optimizes the suspension and traction control of Cybertruck for high-speed driving on dirt roads or in a
desert environment. See Baja on page 124.
NOTE: Cybertruck must be in Park for you to change the drive mode.
CAUTION: The TPMS warning thresholds may be lowered to accommodate different off-roading needs. Do not
rely solely on the TPMS warning indicator when in Off-Road Mode, as these thresholds do not comply with
Federal TPMS standards. It is your responsibility to ensure tires are adequately inflated at all times, and are
inflated back to normal levels before regular driving on roads.

Overland
When you choose Overland, you can customize the following settings:
Setting

Options

Description

Terrain

All
Purpose

Automatically adjusts tire slip based on the amount of available traction and sets the Preferred Ride
Height to High. All Purpose is best suited for mixed terrain driving.

Sand

Allows for high amounts of tire slip to provide optimal traction on soft, deformable surfaces like sand
and sets the Preferred Ride Height to High.

Gravel

Allows for medium amounts of tire slip to provide optimal traction on gravel, and sets the Preferred
Ride Height to High.

Rock

Tightly manages tire slip to maximize grip in rock crawl conditions and sets the Preferred Ride Height
to Very High. When the ride height is Very High, the suspension system pneumatically connects the
springs on the front and rear axles, increasing suspension articulation for maximum traction.

Hold

Applies the brakes automatically when Cybertruck stops, without you having to put your foot on the
brake pedal. Whether stopped on a flat surface or a hill, Vehicle Hold keeps the brake applied,
provided your foot remains off the accelerator and brake pedals.

Stopping
Mode

123

Owner's Manual

Driving
Setting

Options

Description
WARNING: Never rely on Hold to adequately decelerate or fully stop your vehicle. Many factors
can contribute to a longer stopping distance, including downward slopes, and reduced or
limited regenerative braking (see Regenerative Braking on page 116). Always be prepared to use
the brake pedal to adequately decelerate or stop.

Roll

Allows Cybertruck to roll freely when close to, or at, a complete stop, like a vehicle in Neutral.
Therefore, if stopped on a slope, Cybertruck will roll downward. The brake does not engage, and the
motors do not apply torque (until the accelerator pedal is pressed).

Baja
When Cybertruck is in Baja, the ride height is raised to increase suspension travel, rebound, and damping, providing
more stability as well as protection against large impacts. In addition, the electronic stability control system allows
more tire slip for more dynamic driving on low-traction surfaces.
You can customize the following settings:
Setting

Options

Deceleration Mode High

Description
Increases the amount of regenerative braking so Cybertruck slows down more dramatically when
you remove your foot from the accelerator pedal, allowing for more dynamic one-pedal driving.
WARNING: Setting the Deceleration Mode to High may cause some loss of traction on
loose surfaces (such as snow).

Standard Provides the normal level of regenerative braking, allowing Cybertruck to maintain traction on
loose, low-traction surfaces (such as sand, dirt, and gravel).
Handling Balance

Stability Assist

Left

Adjusts the vehicle balance such that Cybertruck behaves more like a front-wheel-drive vehicle.
When you move the slider to the left, Cybertruck is more stable and is more susceptible to
understeer (when you turn the wheel and Cybertruck turns less than normal).

Right

Adjusts the vehicle balance such that Cybertruck behaves more like a rear-wheel-drive vehicle.
When you move the slider to the right, Cybertruck moves with more agility but less stability, and
is susceptible to oversteer (when you turn the wheel and Cybertruck turns more than normal).

Standard Provides the maximum amount of stability control intervention*.
Reduced

Reduces the amount of stability control intervention.

Minimal

Provides a minimal amount of stability control intervention.
WARNING: Drive with caution when Stability Assist is set to Minimal. If you lose control of
Cybertruck, less stability control intervention will be applied and the vehicle may not
stabilize itself.

* Stability control intervention modifies motor torque and selectively applies the brakes to each wheel to make Cybertruck more
stable and help the driver maintain control of the vehicle.

Owner's Manual

124

Driving
Wade Mode
Wade Mode allows Cybertruck to enter and drive through bodies of water. This is especially useful when off-roading
and you need to drive through water, such as rivers or creeks.
CAUTION: It is your responsibility to gauge the depth of any body of water before entering. Damage or water
ingress to Cybertruck as a result of driving in water is not covered by the warranty.
CAUTION: Always inspect underwater conditions (such as debris, etc.) before entering and use your best
judgement. Take care to drive slowly and safely. If the water is too deep, return to more shallow water or dry
land.

1. The maximum wade height is approximately 32.5 in. (82.5 cm) measuring from the bottom of the tire.
Wade Mode must be be used anytime you are driving Cybertruck through a shallow body of water, such as a river. To
enable Wade Mode:
1. Ensure all doors and windows are fully closed.
2. Enable Off-Road Mode.
3. Navigate to Controls > Off-Road Modes > Wade.
NOTE: Your vehicle speed must be less than 20 mph (32 km/h) to enable Wade Mode.
Wade Mode defaults the vehicle’s ride height to Very High and protects Cybertruck for up to approximately 32 in
(80 cm) of water, driving at slow speeds (1-3 mph (2-5 km/h)). As water depth changes, you must reduce your
vehicle speed accordingly. Do not disable Wade Mode until your vehicle is fully out of water.
In addition, the vehicle’s high voltage Battery automatically pressurizes to protect the Battery from water and debris.
Muddy waters can reduce the cooling system effectiveness by adhering to the radiator. See Cleaning Mud on page
209 for information on how to clean your vehicle after a muddy off-roading excursion. Wash your vehicle
immediately after wading to reduce chances of bacteria buildup and mud hardening after drying. Vehicles driving in
waters should be regularly inspected for signs of water ingress or damage to components including (but not limited
to) the brakes, horn, lights, and steering wheel, etc.

125

Owner's Manual

Driving
Wade Mode duration is limited to 30 minutes.
CAUTION: On soft or muddy surfaces underwater, Cybertruck may sink in, effectively increasing the water level
on the vehicle. Take into account this possibility and prepare accordingly.
WARNING: Never stop or place the vehicle in Park when crossing water. Do not drive in water next to, or
immediately after, another vehicle. Currents created by other vehicles can lead to damage.
WARNING: Do not drive in deep, fast-flowing bodies of water (such as strong currents or rapids). Doing so can
result in damage, serious injury, or death.

While Off-Road Driving
You can quickly access off-road settings and monitor the health of Cybertruck in the vehicle status area of the
touchscreen.
• Vitals: Touch Vitals to toggle whether or not the ride height, Battery temperature, and motor temperature is
displayed.
• Ride Height: The current ride height of each wheel is displayed. See Ride & Handling on page 120.
NOTE: When the Ride Height is set to Extract, vehicle speed is limited to 10 mph (16 km/h), and torque may be
limited. The ride height automatically resets to Very High once your driving speed exceeds 10 mph (16 km/h).
• Motor Temp and Battery Temp: The current temperatures of the front and rear motor(s) and the high voltage
Battery are displayed. The temperatures display with no color when operating within their ideal temperature
range. If the performance of the Battery or a motor is reduced due to temperature, the temperature is shown in
yellow. Then, as the performance becomes more limited, the temperature is shown in red.

Limitations and Warnings
Off-road driving depends on the performance of the air suspension system, brakes, power steering, and other
vehicle systems. If there is a condition affecting the performance of any dependent system, a message displays on
the touchscreen and off-road driving modes are unavailable.
WARNING: Before driving off road, carefully survey the terrain and be aware of the weather forecast and other
environmental conditions. Exercise extreme caution when approaching steep ascents and descents. While
driving off road, always be aware of your surroundings and survey the terrain as necessary. Tesla is not liable
for any damage to Cybertruck resulting from off-road driving.
WARNING: Never depend on the driving visualization to show you obstacles in front of, behind, or to the sides
of Cybertruck. Always use caution while driving off road and perform visual checks when necessary. The
visualization relies on the cameras mounted on Cybertruck (see Cameras on page 27). External factors (such
as a dirty or obscured lense) may affect the performance of a camera, and the cameras may not detect objects
or barriers that can potentially cause damage or injury.
WARNING: Visibility may be limited by sharp crests and uneven terrain. Always check what is at the top of a
hill and over the crest before driving over it, and be aware of steep descents or other obstacles.
WARNING: Before approaching an obstacle, ensure that Cybertruck has enough ground clearance to clear it. If
the bottom of Cybertruck is contacting the ground even with the ride height at the highest setting, reduce
your speed or avoid the obstacle altogether.
WARNING: Exercise extra caution when the terrain surface is wet, sandy, or slippery. Loose gravel, sand, and
other environmental conditions may affect the performance of Off-Road Modes.
WARNING: Before driving off road, make sure that loose items in the cabin are stowed or secured and ensure
that the cargo bed is free of cargo, or that cargo is tightly secured.

Driver Profiles
When you first adjust the driver’s seat, steering wheel position, or exterior side mirrors, the touchscreen prompts you
to create a driver profile to save these adjustments. Your profile also saves various preferences you make while
customizing Cybertruck.

Owner's Manual

126

Driving
To save your profile settings to the cloud and access them across multiple Tesla vehicles, set up a Tesla Profile (see
Using Tesla Profiles on page 127).
To add a new driver profile, touch the driver profile icon in Controls. Then touch Driver Profile Settings
> Add New Driver, type the driver's name and touch Create Profile. Follow the onscreen instructions to
save mirror and steering wheel position to the driver profile.

Check the Use Easy Entry checkbox if you want to save (or use existing) Easy Entry settings in which the driver's
seat and the steering wheel are automatically adjusted to make it easy to enter and exit Cybertruck.
If you change the position of the driver’s seat, steering wheel, or exterior side mirrors after you have saved or chosen
a driver profile, the touchscreen prompts you to Save the new position or Restore the previously saved position
(other settings are automatically saved). To change a setting without saving or restoring, just ignore the prompt.
To delete a driver profile, touch the driver profile icon in Controls, touch Driver Profile Settings and select the driver
profile you want to remove. Once selected, Delete the driver profile.
NOTE: Valet mode is a built-in driver profile that limits speed and restricts access to some Cybertruck features (see
Valet Mode on page 128).
NOTE: To stop automatic adjustments that are in process based on a driver's profile, touch Stop on the Driver Profile
dropdown menu. Automatic adjustments also stop if you manually adjust a seat, mirror, or the steering wheel.

Selecting Between Driver Profiles
To adjust Cybertruck based on a driver’s profile, touch the driver profile icon at the top of the Controls
screen. Then choose the driver, and Cybertruck is adjusted based on the settings that have been saved
to the chosen driver profile. See Using Tesla Profiles on page 127 to learn more about saving profile
settings to the cloud for easy access across multiple Tesla vehicles.

Using Tesla Profiles
Driver profile settings, such as seat adjustments, temperature preferences, navigation Recents and Favorites, media
settings, and data sharing preferences can be saved into a Tesla Profile that is synced to every supported vehicle
under your Tesla Account. This provides convenient access to your profile settings and preferences across all your
Tesla supported vehicles.
To set up your Tesla Profile, navigate to Driver Profile Settings and select your Tesla Account name. You can choose
to set it up as a New Profile or copy the settings from an existing driver profile that you were previously using.
To set up a Tesla Profile for additional drivers, share your vehicle with them from the mobile app and navigate to
Security & Drivers > Manage Drivers > Add Driver. Their Tesla Profile will appear in the Driver Profile settings after
accepting the invitation from their Tesla Account. If you remove their access to the vehicle, it also removes their Tesla
Profile. For more information on granting mobile app access, see Granting Access to a Second Driver on page 86. In
addition, you can change your profile picture from your Tesla Mobile App.
NOTE: Some vehicle settings, such as seat, mirror, steering wheel, and air vent positions are only synced between the
same vehicle models. If the seat or steering positions do not restore as expected, touch Controls > Service > Seat &
Steering Calibration on the affected vehicles.
To remove your Tesla Profile from a vehicle, remove that vehicle from your Tesla account:
1. In the Tesla mobile app, touch the profile icon in the top-right corner.
2. Touch Add/Remove Products.
3. Touch Remove.
4. Select the vehicle you'd like to remove.

127

Owner's Manual

Driving
Saved Settings
A subset of the settings that you choose to customize your Cybertruck are automatically saved to your driver's
profile. Once saved, a green check mark appears next to the driver profile icon on the touchscreen. Examples of
automatically saved driver profile settings are:
• Navigation, temperature, lights and display settings.
• Autopilot and driving preferences.

Linking a Driver Profile to a Key
You can link a driver profile to a key (or keys) to allow Cybertruck to automatically select the correct driver profile
when the linked key is detected as you approach the vehicle and open the driver's door. To link a driver profile to a
key, first ensure you are using your desired driver profile, then touch Controls > Locks > Keys. You can toggle the
driver icon to link or delete a key to the desired driver profile. The name of the driver profile appears under the key
to show that it is linked.
NOTE: Cybertruck supports up to 10 driver profiles. You can link multiple keys to a driver profile, but you cannot link
multiple driver profiles to a single key.

Easy Entry
You can define an Easy Entry setting that moves the steering wheel and driver's seat to make it easy to enter and
exit Cybertruck. Any driver can use the Easy Entry setting by associating it with their driver profile. When the Easy
Entry setting is associated with a driver profile, the steering wheel and driver's seat automatically adjust when in
Park and the driver's seat belt is unbuckled, allowing an easy exit from Cybertruck. When returning to the vehicle
and stepping on the brake pedal, settings automatically adjust back to the settings used by the most recent driver
profile (or based on the key if it's linked to a driver profile).
To use Easy Entry with a driver profile, ensure the Use Easy Entry box is checked.
WARNING: Never use Easy Entry to move the driver's seat to the full rearward position when a child safety
seat is installed on a rear seat located behind the driver's seat. With reduced clearance, the movement of the
seat may impact a child's legs, cause injury, or dislodge the seat.

Valet Mode
When Cybertruck is in Valet mode, the following restrictions apply:
• Key card must be used to access and drive Cybertruck.
• Speed is limited to 70 mph (113 km/h).
• Maximum acceleration and power are limited.
• Front trunk and glovebox are locked.
• Home and Work locations are not available in the navigation system.
• Voice commands are disabled.
• Autopilot convenience features are disabled.
• The Allow Mobile Access setting cannot be changed.
• HomeLink (if available in your market region) is not accessible.
• Driver Profiles are not accessible.
• Some apps, such as Toybox and Theater, are not accessible.
• The touchscreen does not display the list of keys that can access Cybertruck (see Managing Keys on page 34).
• Wi-Fi and Bluetooth are disabled. When Cybertruck is in Valet mode, you cannot pair new Bluetooth devices or
view or delete existing paired devices. However, if a Bluetooth-paired device or a known Wi-Fi network is within
range, Cybertruck connects to it.

Owner's Manual

128

Driving
Starting Valet Mode
With Cybertruck in Park, touch the driver profile icon at the top of the Controls screen, then touch Valet Mode.
The first time you enter Valet mode, the touchscreen prompts you to create a 4-digit PIN you will use to cancel Valet
mode.
When Valet mode is active, the touchscreen displays the word Valet while the driver profile changes to Valet Mode
on the touchscreen.