For more information, see the installation guide for your Wall Connector.
CC_f010
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.
CC_f011
Unable to charge - Wall Connector too hot
Let Wall Connector cool and try again
What this alert means:
Over temperature protection (latchoff).
What to do:
Make sure the Wall Connector is not covered by anything and that there is no heat source nearby. If the problem
persists in normal ambient temperatures (under 100°F or 38°C) , service is required.
For more information, see the installation guide for your Wall Connector.

297

Owners Manual
CC_f012
Unable to charge - Wall connection too hot
Outlet or Wall Connector wiring must be checked
High temperature detected by Wall Connector alerts indicate the building connection to the Wall Connector is
getting too warm, so charging has stopped to protect the wiring and Wall Connector.
This is not typically an issue with your vehicle or your Wall Connector, but rather an issue with the building wiring.
This may be caused by a loose building wiring connection to the Wall Connector and can be fixed quickly by an
electrician.
To regain normal charge operation, try the following steps.
If the Wall Connector is plugged into a wall outlet, make sure:
• The plug is fully inserted into the receptacle / outlet
• The plug / outlet area is not blocked or covered by anything
• There is no heat source nearby
If the issue persists or the Wall Connector is hard-wired, contact an electrician to inspect the building wiring
connection to the Wall Connector. They should make sure that all wires are properly connected and torqued
according to the installation guide for the Wall Connector.
For more information, see the installation guide for your Wall Connector.
CC_f013
Unable to charge - Charge handle too hot
Check charge handle or charge port for debris
What this alert means:
Over temperature protection (latchoff).
What to do:
Make sure the connector is fully inserted into the charge inlet in the vehicle's charging port, is not covered by
anything, and there is no heat source nearby. If the issue persists in normal ambient temperatures (under 100°F or
38°C) , service is required.
For more information, see the installation guide for your Wall Connector.
CC_f014
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
298

Owners Manual
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.
CC_f015
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f016
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f017
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.

299

Owners Manual
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f018
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f019
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f020
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected

300

Owners Manual
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.
CC_f021
Unable to charge - No primary Wall Connector
Check that primary unit is powered and available
What this alert means:
Load sharing (circuit breaker sharing) network: Need one (and only one) Wall Connector set as primary.
What to do:
Only one Wall Connector can be set to a primary configuration. Have your electrician confirm:
1. Only one of the Wall Connectors is set as primary.
2. All other Wall Connectors linked to the primary unit are set to paired position (position F).
For more information, see the installation guide for your Wall Connector.
CC_f022
Unable to charge - More than 1 primary unit
Ensure only 1 Wall Connector is set as primary
What this alert means:
Load sharing (circuit breaker sharing) network: Need one (and only one) Wall Connector set as primary.
What to do:
Only one Wall Connector can be set to a primary configuration. Have your electrician confirm:
1. Only one of the Wall Connectors is set as primary.
2. All other Wall Connectors linked to the primary unit are set to paired position (position F).
For more information, see the installation guide for your Wall Connector.
CC_f023
Unable to charge - Too many Wall Connectors
Ensure no more than 3 units paired with primary
What this alert means:
Load sharing (circuit breaker sharing) network: More than three Wall Connectors are paired with the same primary
unit.
What to do:
301

Owners Manual
Consult your electrician to have one or more paired Wall Connectors moved to a different circuit and disconnected
(unpaired) from this load sharing (circuit breaker sharing) network.
For more information, see the installation guide for your Wall Connector.
CC_f024
Unable to charge - Low Wall Connector current
Primary unit current setting must be increased
What this alert means:
Incorrect rotary switch setting.
What to do:
Have your electrician adjust the Wall Connector’s internal rotary switch to a valid operating current setting. They
should first make sure there is no power to the Wall Connector. The correlation between switch setting and current
should be printed on the inside of the Wall Connector. Your electrician should also refer to the Set the Operating
Current section in the Wall Connector Installation Manual.
If the Wall Connector is set up for load sharing (circuit breaker sharing) and paired with other Wall Connectors, the
rotary switch of the primary unit must be set to an operating current setting that allows each paired Wall Connector
to receive at least 6A of charge current.
Example: Three Wall Connectors are paired for load sharing. The primary unit needs to be set to a current of at least
3 * 6A = 18A or greater.
For more information, see the installation guide for your Wall Connector.
CC_f025
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.

302

Owners Manual
CC_f026
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.
CC_f027
Unable to charge - Wall Connector issue
Wall Connector needs service
What this alert means:
Wall Connector hardware issue. Possible issues include:
1. Contactor not working
2. Self-test of internal ground fault monitoring circuit failed
3. Thermal sensor disconnected
4. Other hardware component issues
What to do:
An internal issue was detected by the Wall Connector.
1. Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
2. If the issue persists, turn OFF the circuit breaker for the Wall Connector, wait 10 seconds, and turn the circuit
breaker ON again. Then try reconnecting the Wall Connector to the vehicle.
3. If the issue persists, have an electrician make sure all wires are properly connected and torqued according to the
instructions in the Wall Connector Installation Manual.
4. Once your electrician has completed all work and restored power to the Wall Connector, try charging again by
reconnecting the Wall Connector to the vehicle.
5. If the issue persists, the Wall Connector requires service.
For more information, see the installation guide for your Wall Connector.

303

Owners Manual
CC_f028
Unable to charge - Incorrect switch setting
Wall Connector rotary switch must be adjusted
What this alert means:
Incorrect rotary switch setting.
What to do:
Have your electrician adjust the Wall Connector’s internal rotary switch to a valid operating current setting. They
should first make sure there is no power to the Wall Connector. The correlation between switch setting and current
should be printed on the inside of the Wall Connector. Your electrician should also refer to the Set the Operating
Current section in the Wall Connector Installation Manual.
If the Wall Connector is set up for load sharing (circuit breaker sharing) and paired with other Wall Connectors, the
rotary switch of the primary unit must be set to an operating current setting that allows each paired Wall Connector
to receive at least 6A of charge current.
Example: Three Wall Connectors are paired for load sharing. The primary unit needs to be set to a current of at least
3 * 6A = 18A or greater.
For more information, see the installation guide for your Wall Connector.
CC_f029
Unable to charge - Vehicle connection issue
Insert charge handle fully into charge port
What this alert means:
A communication error occurred between the Wall Connector and the vehicle.
What to do:
Try charging again by disconnecting the Wall Connector from the vehicle and reconnecting.
1. If the issue persists, turn OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit
breaker ON again, then try reconnecting the Wall Connector to the vehicle.
2. If the issue persists and other charging equipment is available, plug the vehicle into another Wall Connector or a
Mobile Connector to determine if the vehicle is able to communicate with other charging equipment.
3. If the issue persists, service is required.
For more information, see the installation guide for your Wall Connector.
CC_f030
Unable to charge - Primary / paired unit mismatch
Wall Connector current ratings must match
What this alert means:
Load sharing (circuit breaker sharing) network: The paired Wall Connectors have different maximum current
capabilities.
What to do:
Only Wall Connectors with the same maximum current capabilities can be paired in a load sharing (circuit breaker
sharing) network. Have your electrician inspect the type labels on the Wall Connectors and make sure the current
capabilities match. It is further recommended that your electrician only pair Wall Connectors with the same part
number, as an easy way to make sure paired units are compatible.
For more information, see the installation guide for your Wall Connector.

304

Owners Manual
CC_f041
Charge rate reduced - Wall connection hot
Outlet or Wall Connector wiring must be checked
What this alert means:
High temperature detected by Wall Connector alerts indicate the building connection to the Wall Connector is
getting too warm, so charging has been slowed to protect the wiring and Wall Connector.
This is not typically an issue with your vehicle or your Wall Connector, but rather an issue with the building wiring.
This may be caused by a loose building wiring connection to the Wall Connector and can be fixed quickly by an
electrician.
What to do:
Contact an electrician to inspect the building wiring connection to the Wall Connector. They should make sure that
all wires are properly connected and torqued according to the installation guide for the Wall Connector.
For more information, see the installation guide for your Wall Connector.
CHG_f035
Charging equipment communication error
Try again or try different equipment
What this alert means:
Your vehicle is unable to charge because it cannot communicate effectively with the external charging equipment. It
cannot sense a valid control pilot signal coming from the charging equipment.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
What to do:
First, confirm the lack of effective communication is caused by the external charging equipment rather than an issue
with your vehicle. This is usually the case.
Try charging the vehicle using different external charging equipment (including charge cable, charging station, or
charging stall).
• If the vehicle begins charging, the issue was likely with the equipment.
• If the vehicle still does not charge, the issue may be with the vehicle.
If the issue is suspected to be with the vehicle, inspect the charge port inlet and the charge cable connector for any
obstructions, such as debris, moisture, and/or foreign objects. Make sure any charge port inlet obstruction has been
removed and any moisture has been allowed to dry, then try re-inserting the cable into the charge port.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
For more information on charging, see Charging Instructions on page 219.
CHG_f083
Cannot charge - Poor grid power quality possible
Retry / Try other charge location or Supercharging
What this alert means:
Power has been lost during charging. This could result from the charging equipment losing power from the source
(for example, a wall outlet) or from an issue with the charging equipment.
305

Owners Manual
What to do:
This alert is often accompanied by other alerts that can help you identify and troubleshoot the issue. Start by
investigating any other displayed alerts that relate to charging issues.
Alternatively, you can check Mobile Connector or Wall Connector status lights to confirm power to the device, and
also refer to the product owner’s manual for troubleshooting information based on blink codes. If using other (nonTesla) external charging equipment, check for a display or other user interface that provides troubleshooting help.
If there is clearly no power to the charging equipment, check the circuit breaker for the wall outlet / Wall Connector
to make sure it has not tripped.
Further troubleshooting tips based on equipment type:
• If using a Mobile Connector, try charging the vehicle with a different wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the original wall outlet.
◦ If the vehicle still does not charge, the issue may be with the Mobile Connector.
• If using a Wall Connector, try charging the vehicle with different charging equipment like a Mobile Connector
powered by a separate wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the Wall Connector.
If the issue is with the original wall outlet or the Wall Connector, contact an electrician to inspect the wiring
connection.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
CHG_f091
Charging equipment not recognized
Try again or try different equipment
What this alert means:
The charge port is unable to detect whether a charge cable is inserted, or the type of charge cable connected.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
What to do:
If this alert appears while a charge cable is connected, determine whether the issue is caused by the charging
equipment or the vehicle. Try charging the vehicle using different external charging equipment (including charge
cable, charging station, or charging stall).
• If the vehicle begins charging, the issue was likely with the equipment.
• If the vehicle still does not charge, the issue may be with the vehicle.
If this alert appears while a charge cable is not connected or if the issue is suspected to be with the vehicle, inspect
the charge port inlet and the charge cable connector for any obstructions, such as debris, moisture, and/or foreign
objects. Make sure any charge port inlet obstruction has been removed and any moisture has been allowed to dry,
then try re-inserting the cable into the charge port.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
306

Owners Manual
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
For more information on charging, see Charging Instructions on page 219.
CHGS_f083
Cannot charge - Poor grid power quality possible
Retry / Try other charge location or Supercharging
What this alert means:
Power has been lost during charging. This could result from the charging equipment losing power from the source
(for example, a wall outlet) or from an issue with the charging equipment.
What to do:
This alert is often accompanied by other alerts that can help you identify and troubleshoot the issue. Start by
investigating any other displayed alerts that relate to charging issues.
Alternatively, you can check Mobile Connector or Wall Connector status lights to confirm power to the device, and
also refer to the product owner’s manual for troubleshooting information based on blink codes. If using other (nonTesla) external charging equipment, check for a display or other user interface that provides troubleshooting help.
If there is clearly no power to the charging equipment, check the circuit breaker for the wall outlet / Wall Connector
to make sure it has not tripped.
Further troubleshooting tips based on equipment type:
• If using a Mobile Connector, try charging the vehicle with a different wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the original wall outlet.
◦ If the vehicle still does not charge, the issue may be with the Mobile Connector.
• If using a Wall Connector, try charging the vehicle with different charging equipment like a Mobile Connector
powered by a separate wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the Wall Connector.
If the issue is with the original wall outlet or the Wall Connector, contact an electrician to inspect the wiring
connection.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
CHG_u001
Charge rate reduced - Unexpected voltage drop
Remove extension cords / Have wiring inspected
What this alert means:
Charging speed has been reduced because the onboard charger in your vehicle has detected a large voltage drop
during charging.
Likely causes of this issue include:
• Problems with the building wiring and/or the wall outlet.
• An extension cord or other wiring that cannot support the requested charge current.

307

Owners Manual
This issue can also result from turning on electric devices that draw a lot of power from the same branch circuit
while the vehicle is charging.
What to do:
If this issue has occurred multiple times at your normal charging location, contact an electrician to inspect the
electrical installation. They should check the following:
• Any installed charging equipment and its connection to the building wiring.
• The building wiring, including any wall outlet used with a Mobile Connector.
• The electrical connection to the power utility line where it enters the building.
Discuss with the electrician whether the charge current on the vehicle should be lowered, or if the installation should
be upgraded to support a higher charge current.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
CHG_u002
Charging stopped due to large voltage drop
Remove extension cords / Have wiring inspected
What this alert means:
Charging has been interrupted because the onboard charger in your vehicle has detected an unusually large voltage
drop.
Likely causes of this issue include:
• Problems with the building wiring and/or the wall outlet.
• An extension cord or other wiring that cannot support the requested charge current.
This issue can also result from turning on electric devices that draw a lot of power from the same branch circuit
while the vehicle is charging.
What to do:
If this issue has occurred multiple times at your normal charging location, contact an electrician to inspect the
electrical installation. They should check the following:
• Any installed charging equipment and its connection to the building wiring.
• The building wiring, including any wall outlet used with a Mobile Connector.
• The electrical connection to the power utility line where it enters the building.
Discuss with the electrician whether the charge current on the vehicle should be lowered, or if the installation should
be upgraded to support a higher charge current.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.

308

Owners Manual
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
CHG_u004
Charging stopped - Power lost while charging
Check power source and charging equipment
What this alert means:
Power has been lost during charging. This could result from the charging equipment losing power from the source
(for example, a wall outlet) or from an issue with the charging equipment.
What to do:
This alert is often accompanied by other alerts that can help you identify and troubleshoot the issue. Start by
investigating any other displayed alerts that relate to charging issues.
Alternatively, you can check Mobile Connector or Wall Connector status lights to confirm power to the device, and
also refer to the product owner’s manual for troubleshooting information based on blink codes. If using other (nonTesla) external charging equipment, check for a display or other user interface that provides troubleshooting help.
If there is clearly no power to the charging equipment, check the circuit breaker for the wall outlet / Wall Connector
to make sure it has not tripped.
Further troubleshooting tips based on equipment type:
• If using a Mobile Connector, try charging the vehicle with a different wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the original wall outlet.
◦ If the vehicle still does not charge, the issue may be with the Mobile Connector.
• If using a Wall Connector, try charging the vehicle with different charging equipment like a Mobile Connector
powered by a separate wall outlet.
◦ If the vehicle starts to charge, the issue was likely with the Wall Connector.
If the issue is with the original wall outlet or the Wall Connector, contact an electrician to inspect the wiring
connection.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
CHG_u005
Unable to charge - Charge station not powered
Check power source or try a different station
What this alert means:
Charging cannot begin because the charging equipment is not ready. A charge handle is detected, but the charging
station is not communicating with the vehicle. This issue could occur because:
• The charging station is not powered.
• The control pilot signal between the charging station and the vehicle is interrupted.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
What to do:
309

Owners Manual
Try charging the vehicle with different charging equipment or at a different charging station.
• If the vehicle begins charging, the issue was likely with the equipment.
• If the vehicle still does not charge, the issue may be with the vehicle.
If using a Mobile Connector or Wall Connector, first check the status lights on the front. If no status lights are visible,
check the power source and contact an electrician to inspect the building wiring connection to the wall outlet or the
Wall Connector to confirm that all wires are properly connected and torqued.
If using other external charging equipment, consult the product's owner's manual to learn how to confirm that the
station is powered. Contact an electrician to inspect the building wiring and charging equipment as necessary.
For more information on troubleshooting Mobile Connector or Wall Connector status lights, refer to the product's
Owner's Manual at Charging & Adapter Product Guides.
You can also try charging your vehicle using a Tesla Supercharger or Destination Charging location, all of which can
be located through the map on your vehicle's touchscreen display. See Maps and Navigation on page 200 for more
details.
CHG_u006
Charge port latch not engaged
Fully insert charge cable or check for obstruction
What this alert means:
The charge port latch is unable to latch the charge cable in the charge port inlet. If the latch is not engaged, AC
charging (for example, charging with a Mobile Connector or Wall Connector) will be limited to 16A and DC Fast
Charging / Supercharging will be unavailable.
The charge port light will pulse amber if this alert appears during AC charging and will be solid amber if this alert
appears when attempting to DC Fast Charge / Supercharge.
This alert is usually specific to external charging equipment and power sources and does not typically indicate an
issue with your vehicle that can be resolved by scheduling service.
What to do:
Try re-inserting the charge cable fully into the charge port inlet.