Circuit Board
(Replace)

TFT
(Reuse)

5. Assemble the center display in the reverse order of disassemble.
NOTE:
Page 12 of 25

12/06/2023 02:18 PM tlawrenc

•
•
•
•

Hold both edges of the cable and insert the cable carefully so that the cable will not be damaged.
After locking the lock tab, check that the line of the circuit board (1) and the line of the cable are aligned.
When installing the bracket B to the center display, apply the 4 snap-fits properly.
After screwing together the bracket B and the center display, check that the screws are seated properly. [Screw]
M3 x 9 mm 4 pcs.
• When installing the rear cover the center display assy., apply the 4 snap-fits properly.
• After screwing together the center display assy. and the rear cover, check that the screws are seated properly,
and then retightening them. [Screw] center: M3 x 16 mm with washer 2 pcs., outside: M3 x 15 mm 2 pcs.
• After screwing together the center display assy. and the bracket A, check that the screws are seated properly, and
then retightening them. [Screw] M3 x 16 mm with washer 2 pcs.
6. Install the center display in the reverse order of removal.
7. Verify the repair.

Page 13 of 25

12/06/2023 02:18 PM tlawrenc

MX-5 Repair:
1. Check the part number (2) on the label (1) of the center display and then confirm the new replacement part number in
the Parts Information.

(1) Label

(2) Part number

(Center display lens kit)
(Modified part)

Frame color of the center display

D0YP-61-1JZ

Silver

D0YH-61-1JZB

Silver

D1YP-61-1JZ

Piano Black

D1YN-61-1JZB

Piano Black

D2YN-61-1JZA

Piano Black

Center display assy. on the vehicle
(Old part)
N247-61-1J0A or older part,
NA1P-61-1J0B or older part
N315-61-1J0
ND1F-61-1J0A or older part
N315-61-1J0A/B,
ND1F-61-1J0B/C

2. Remove the 4 screws (1), then remove the connectivity master unit (CMU) (2) from the center display (3).

3. Place the cushion sheet (1) that the lens was wrapped in, on a workbench.
4. Put on the rubber gloves.
5. Place the center display (2) on the cushion sheet (1) with the display side facing downward.
Page 14 of 25

12/06/2023 02:18 PM tlawrenc

6. Remove the 3 screws (1) and separate the center display (2) and the bracket A (3).

NOTE: After screwing together the center display (2) and the bracket A (3), check that the screws (1) are seated
properly, and then retighten them. (Screw: M5 x 10 mm with a washer)
7. Remove the 4 screws (1) on the backside and the bottom of the center display, and then remove the panel (2) from
the center display (3).

NOTE: After screwing together the center display (3) and the panel (2), check that the screws (1) are seated properly,
and then retighten them. (Screw: M3 x 16 mm with a washer)
Page 15 of 25

12/06/2023 02:18 PM tlawrenc

Page 16 of 25

12/06/2023 02:18 PM tlawrenc

8. Remove the 2 screws (1) on backside of the center display (2), then unhook (3) and remove the rear cover (4) from
the center display (2).

NOTE:
• When installing the rear cover (4) to the center display (2), apply the 4 snap-fits (3) properly.
• After screwing the center display (2) and the rear cover (4), check that the screws (1) are seated properly, then
retighten them. (Screw: M3 x 15 mm with a washer)
9. Remove the 4 screws (1) that attach the center display (2) and the bracket B (3).

NOTE: After screwing together the bracket B (3) and the center display (2), check that the screws (1) are seated
properly. (Screw: M3 x 9 mm)

Page 17 of 25

12/06/2023 02:18 PM tlawrenc

10. Remove the bracket B (1) from the center display (2).
NOTE: There are 2 snap-fits (3) on the left and right side of the center display.

Assembly of the center displa
y and the bracket B

Holes of the bracket B

Hooks on the center display

11. Insert a tip of a flathead screwdriver in underside the gap (2), and then remove the bracket B (1) partially.
NOTE: When inserting the screwdriver, DO NOT damage the circuit board.

Detail A
Insert a flathead screwdriver.

Page 18 of 25

12/06/2023 02:18 PM tlawrenc

12.Insert a tip of a flathead screwdriver in upper side of the gap (1), then remove the bracket B.

Bracket B

Center display

13. Pull up the lock tab (1) to unlock the connector.
NOTE: Pull the lock tab (1) gently to avoid the lock tab (1) from being damaged.

Lock:

Unlock
Detail A
(1) Lock tab (2) Cable

Page 19 of 25

12/06/2023 02:18 PM tlawrenc

NOTE: After locking the lock tab (1), check that the line of the cable (2) and the line of the circuit board (3) are aligned.

14. Hold both edges of the cable, then pull it out.

Detail A
NOTE: Hold both edges of the cable and insert the cable carefully so that the cable will not be damaged.
15. Remove the center display from the lens.
16. Perform Procedure C or Procedure D:
Procedure C:
1. Replace the lens with a modified one, but reuse the center display
NOTE:
• When installing the center display to the modified lens, clear foreign objects and contamination on the lens and
the center display.
• When installing the center display to the modified lens, check that a gasket has been installed to the lens properly.

Page 20 of 25

12/06/2023 02:18 PM tlawrenc

Replace: Lens

Reuse: Center display

Procedure D:
1. Remove TFT (1) from the circuit board (2) according to the following procedure.

2. Unlock the clock tab (3) (4) of the center display according to Detail for A and B.
NOTE: Pull the lock tab (3) (4) gently to avoid damaging it.
3. Hold both edges of the cables (4) (5), and pull them out according to Detail for A and B.
Detail for A:

Page 21 of 25

12/06/2023 02:18 PM tlawrenc

(3) Lock Tab

(3) Lock Tab (unlocked)

(5) Cable

Detail for B:

(4) Lock Tab

(4) Lock Tab (unlocked)

(6) Cable

4. Replace the lens and circuit board with modified parts.
NOTE: Reuse the TFT.

Lens
Circuit Board
(Replace)
(Replace)
5. Assemble the center display in the reverse order of disassemble.
NOTE:

TFT
(Reuse)

• Hold both edges of the cable and insert it carefully so that the cable will not be damaged.
• After locking the lock tab, check that the line of the circuit board and the line of the cable are aligned.
• After screwing together the bracket B and the center display, check that the screws are seated properly. [Screw:
M3 x 9 mm, 4 pcs.]
• When installing the rear cover to the center display, apply the 4 snap-fits properly.
• After screwing together the center display and the rear cover, check that the screws are seated properly, and then
retighten them. [Screw: M3 x 15 mm with a washer, 2 pcs.]
• After screwing together the center display and panel, check that the screws are seated properly, and then
retighten them. [Screw: M3 x 16 mm with washer, 2 pcs.]
• After screwing together the center display and the bracket A, check that the screws are seated properly, and then
retighten them. [Screw: M5 x 10 mm with a washer, 3 pcs.]
6. Install the center display in the reverse order of removal.
7. Verify the repair.
Page 22 of 25

12/06/2023 02:18 PM tlawrenc

Page 23 of 25

12/06/2023 02:18 PM tlawrenc

PARTS INFORMATION
Mazda2 / CX-3:
Parts Number (New Part)

Center display on the vehicle (Old part)

Description

Qty.

D09H-61-1J0B or older part

Center Display Lens Kit

1

D23N-61-1J0A or older part

Center Display Lens Kit

1

Center Display Lens Kit

1

D0YP-61-1JZ *Note 3
D0YH-61-1JZB *Note 3
D1YP-61-1JZ *Note 4
D1YN-61-1JZB *Note 4
D2YN-61-1JZA

D23N-61-1J0B

NOTE:
• Refer to GEPC to select the applicable display assembly part number.
• D23N-61-1J0C is the modified part.
Note 3. D0YP-61-1JZ will be superseded to D0YH-61-1JZB.
Note 4. D1YP-61-1JZ will be superseded to D1YN-61-1JZB.
MX-5:
Parts Number (New Part)

Center display on the vehicle (Old part)

Description

Qty.

D0YP-61-1JZ *Note 2

N247-61-1J0A or older part
NA1P-61-1J0B or older part

Center Display Lens Kit

1

N315-61-1J0
ND1F-61-1J0A or older part

Center Display Lens Kit

1

Center Display Lens Kit

1

D0YH-61-1JZB *Note 2
D1YP-61-1JZ *Note 3
D1YN-61-1JZB *Note 3
D2YN-61-1JZA

N315-61-1J0A/B
ND1F-61-1J0B/C

NOTE: Refer to GEPC to select the applicable display assembly part number.
Note 2. D0YP-61-1JZ will be superseded to D0YH-61-1JZB.
Note 3. D1YP-61-1JZ will be superseded to D1YN-61-1JZB.
WARRANTY INFORMATION
NOTE:
• This warranty information applies only to verified customer complaints on vehicles eligible for warranty repair.
• This repair will be covered under Mazda's New Vehicle Limited Warranty term.

Page 24 of 25

12/06/2023 02:18 PM tlawrenc

• Additional diagnostic time cannot be claimed for this repair.
Warranty Type
Symptom Code

61

Damage Code

9W

Part Number Main Cause
Quantity
Operation Number / Labor Hours:

****-61-1JZ*
1
XXW4WBRX / 0.5 Hrs. (CX-3, Mazda2)
XXW4WCRX / 0.6 Hrs. (MX-5)

Page 25 of 25

12/06/2023 02:18 PM tlawrenc