BULLETIN NOTES
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red.
Previous TSBs:

Date(s) Issued:

09-003/23

01/03/23 and 01/12/23

09-036/22

09/09/22

APPLICABLE MODEL(S)/VINS:
2016-2021 Mazda2 (Mexico/Puerto Rico) with VINS lower than 3MDDJ******409029 (produced before July 14, 2021)
2022 Mazda2 (Mexico) with VINS lower than 3MDDJ******452968 (produced before February 3, 2022)
2016-2022 CX-3 with VINS lower than JM1DK******604871 (produced before April 28, 2022)
2016-2022 MX-5
DESCRIPTION
Some customers may complain about infotainment center display:
• Center display touchscreen operates by itself (Ghost Touch).
• The film of the center display may be peeled off.
• White dots may appear on the center display
NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.

Page 1 of 25

12/06/2023 02:18 PM tlawrenc

• Ghost Touch

(Touch screen operates by itself)

Peeling of the film surface
of the center display

White dots on the
center display

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.
Customers having this concern should have their vehicle repaired using the following repair procedure.

REPAIR PROCEDURE
1. Verify customer concern
2. Remove the center display.
NOTE: Wear the rubber gloves to protect the center display lens kit and to prevent static electricity.
3. Verify the part number on the label of the center display and ensure that the replacement kit part number is correct.
4. Place the cushion sheet that the lens is wrapped on a working table.
NOTE: This cushion sheet contains an antistatic agent that not only prevents parts from being scratched, but also
prevents static electricity.
5. Replace the lens (inner part) with the modified one.

Page 2 of 25

12/06/2023 02:18 PM tlawrenc

Attention
1. Due to the semiconductor shortage, new modified center display lens kits have been added. The current modified
part will be replaced with the new part depending on the available stock. The modified part number you receive may
differ from the current part, however, the performance and quality are the same.
2. The repair procedure is different between the current modified part and the new part. When receiving the modified
part, check the part number before repairing the vehicle, then repair it according to the applicable repair procedure.
Model

Mazda2 / CX-3

Current modified parts
(Center display lens kit)
D0YP-61-1JZ

(See Procedure A)

D0YH-61-1JZB

(See Procedure B)

D1YP-61-1JZ

(See Procedure A)

D1YN-61-1JZB

(See Procedure B)

D2YN-61-1JZA

MX-5

No.

New modified parts
(Center display lens kit)

(See Procedure A)

---

D0YP-61-1JZ

(See Procedure C)

D0YH-61-1JZB

(See Procedure D)

D1YP-61-1JZ

(See Procedure C)

D1YN-61-1JZB

(See Procedure D)

D2YN-61-1JZA

(See Procedure C)

Description

---

Qty.

Notes

(1)

Center display lens kit

1

Cushion materials for packa
ging are used as work mat to
protect parts from static elect
ricity and scratches.
Parts number: Refer to PAR
TS INFORMATION.

(2)

Rubber gloves

1

Anti-static

(1) Center display lens

(2) Rubber gloves

NOTE:
• Center display lens is packaged by a bubble wrap (3) and a cushion material (4). Unwrap the package carefully so
that the packaging materials is used as an antistatic work mat.
Page 3 of 25

12/06/2023 02:18 PM tlawrenc

• Unwrap the center display lens gently to avoid damaging the cable (5) (FPC: Flexible Printed Circuit) equipped on
the lens.

(3) Bubble wrap

(4) Cushion material

(5) Cable: Flexible Printed Circuit

CENTER DISPLAY DISASSEMBLY:
1. Remove the center display according to the instructions on MGSS.
• Mazda2: CENTER DISPLAY REMOVAL/INSTALLATION
• CX-3: CENTER DISPLAY REMOVAL/INSTALLATION
• MX-5: CENTER DISPLAY REMOVAL/INSTALLATION

Page 4 of 25

12/06/2023 02:18 PM tlawrenc

Mazda2 / CX-3 Repair:
1. Check the part number (2) on the label (1) of the center display and then confirm the new replacement part number in
the Parts Information.

(1) Label

(2) Part number

(Center display lens kit)
(Modified part)

Frame color of the center display

Center display assy. on the vehicle
(Old part)

D0YP-61-1JZ

Silver

D09H-61-1J0B or older part

D0YH-61-1JZB

Silver

---

D1YP-61-1JZ

Piano Black

D23N-61-1J0A or older part

D1YN-61-1JZB

Piano Black

---

D2YN-61-1JZA

Piano Black

D23N-61-1J0B

2. Remove the 4 screws (1), then remove the connectivity master unit (CMU) (2) from the center display (3).

3. Place the cushion sheet (1) that the lens was wrapped in, on a workbench.
4. Put on the rubber gloves.
5. Place the center display (2) on the cushion sheet (1) with the display side facing downward.
Page 5 of 25

12/06/2023 02:18 PM tlawrenc

Page 6 of 25

12/06/2023 02:18 PM tlawrenc

6. Remove the 2 screws (1). Separate the center display (2) and the bracket A (3).

NOTE: After screwing together the center display and the bracket A (3), check that the screws (1) are seated properly,
and then retighten them. (Screw: M3 x 16 mm with a washer)
7. Remove the 4 screws (1) on backside of the center display (2), unhook the 4 snap-fits (3), then remove the rear cover
(4) from the center display (2).

NOTE:
• When installing the rear cover (4) to the center display (2), apply the 4 snap-fits (3) properly.
• After screwing together the center display (2) and the rear cover (4), check that the screws (1) are seated
properly and then retighten them. (Screw: center: M3 x 16 mm with washer, outside: M3 x 15 mm)

Page 7 of 25

12/06/2023 02:18 PM tlawrenc

8. Remove the 4 screws (1) that attach the center display (2) and the bracket B (3).

NOTE: After screwing together the bracket B (3) and the center display (2), check that the screws (1) are seated
properly. (Screw: M3 x 9 mm )
9. Remove the bracket B (1) from the center display (2).
NOTE: There are 2 snap-fits (3) on the left and right side of the center display.

Assembly of the center displa
y and the bracket B

Holes of the bracket B

Hooks on the center display

10. Insert a tip of a flathead screwdriver in the underside of the gap (2), and then move up the bracket B (1) partially.
NOTE: When inserting the screwdriver, be careful NOT to damage the circuit board.

Detail A
Insert a flathead screwdriver.
Page 8 of 25

12/06/2023 02:18 PM tlawrenc

11. Insert a tip of a flathead screwdriver in upper side of the gap (1), then remove the bracket.

Bracket B

Center display

12. Pull up the lock tab (1) to unlock the connector.
NOTE: Pull the lock tab (1) gently to avoid the lock tab to be damaged.

Page 9 of 25

12/06/2023 02:18 PM tlawrenc

Lock:

Unlock
Detail A
(1) Lock tab (2) Cable

NOTE: After locking the lock tab (1), check that the line of the cable (2) and the line of the circuit board (3) are aligned.

13. Hold both edges of the cable, then pull it out.

Detail A
Page 10 of 25

12/06/2023 02:18 PM tlawrenc

NOTE: Hold both edges of the cable and insert the cable carefully so that the cable will not be damaged.
14. Remove the center display from the lens.
15. Perform Procedure A or Procedure B.
Procedure A:
1. Replace the lens with the modified one, reusing the center display.
NOTE:
• When installing the center display to the modified lens, clear foreign objects and contamination on the lens and
the center display.
• When installing the center display to the modified lens, check that a gasket has been installed to the lens properly.

Replace: Lens

Reuse: Center display

Procedure B:
1. Remove TFT (1) from the circuit board (2) according to the following procedure.

2. Unlock the lock tab (3) (4) of the center display according to Detail for A and B.
NOTE: Pull the lock tab (3) (4) gently to avoid damaging it.

Page 11 of 25

12/06/2023 02:18 PM tlawrenc

3. Hold both edges of the cables (5) (6), and pull them out according to Detail for A and B.
Detail for A:

(3) Lock Tab

(3) Lock Tab

(5) Cable

Detail for B:

(4) Lock Tab

(4) Lock Tab

(6) Cable

4. Replace the lens and circuit board with modified parts.
NOTE: Reuse the TFT.

Lens
(Replace)