2013 Cadillac XTS
This information replaces the information located under “Memory Seats” found in Section 3 of your
owner manual
If equipped, the SET, "1," "2," and
(Exit) buttons on the
driver door are used to manually save and recall memory
settings for the driver seat, outside mirrors, and power tilt and
telescoping steering column.

Storing Memory Positions
To save positions to the “1” and “2” buttons:

3223104

1. Adjust the driver seat, outside mirrors, and the power tilt and telescoping steering column to
the desired driving positions.
2. Press and hold SET and “1” at the same time until a beep sounds.
3. Repeat Steps 1 and 2 for a second driver using “2.”
To save positions to the
(Exit) button and easy exit features:
1. Adjust the driver seat, power tilt and telescoping steering column, and the outside mirrors on
some vehicles to the desired positions for getting out of the vehicle.
2. Press and hold SET and

at the same time until a beep sounds.

Manually Recalling Memory Positions
Press and hold "1," "2," or
to manually recall the previously stored memory positions. Releasing
"1,” "2," or
before the stored positions are reached stops the recall.
There is also the ability to press and release “1,” “2,” or
to manually recall the previously stored
memory positions. The ignition must be in ON/RUN/START, and the transmission must be in P (Park).
Placing the ignition in OFF before the stored positions are reached stops the recall.
If something has blocked the driver seat and/or power tilt and telescoping steering column while
recalling a memory position, the recall may stop. Remove the obstruction; then press and hold the
appropriate manual control for the memory item that is not recalling for two seconds. Try recalling
the memory position again by pressing the appropriate memory button. If the memory position is
still not recalling, see your dealer for service.

Recalling RKE Memory Positions (Auto Memory Recall)
The Auto (Automatic) Memory Recall feature automatically recalls the current driver’s previously
stored “1” or “2” position when entering the vehicle.
When the Auto Memory Recall feature is enabled in the vehicle personalization menu, memory “1” or
“2” positions are recalled in the following ways:
To activate the recall when On - Driver Door Open is selected in the personalization menu, do one of
the following:
• Press
on the RKE transmitter and open the driver door.
• Press

on the RKE transmitter when the driver door is already open.

• Press the lock/unlock button on the outside driver door handle and open the driver door. The
RKE transmitter must be present for the recall to activate.
To activate the recall when On - At Ignition On is selected in the vehicle personalization menu:
• Place the ignition in ON/RUN/START.
See Vehicle Personalization.
To stop recall movement, press one of the memory, power mirror, or power seat controls; or press
the power tilt and telescoping steering column control. If On - At Ignition On is selected in the vehicle
personalization menu, placing the ignition in OFF also stops the recall.
If something has blocked the driver seat and/or the power tilt and telescoping steering column while
recalling a memory position, the recall may stop. Remove the obstruction; then press and hold the
appropriate manual control for the memory item that is not recalling for two seconds. Try recalling
the memory position again by opening the driver door and pressing
on the RKE transmitter. If the
memory position is still not recalling, see your dealer for service.

Easy Exit Recall
If programmed on in the vehicle personalization menu, the easy exit feature automatically moves the
driver seat, power tilt and telescoping steering column, and outside mirrors on some vehicles to the
memory positions saved to the
(Exit) button. See “Storing Memory Positions” listed previously.
See also Vehicle Personalization.
Easy exit recall automatically activates when one of the following occurs:
• The vehicle is turned off and the driver door is opened within a short time.
• The vehicle is turned off with the driver door open.
If something has blocked the driver seat and/or power tilt and telescoping steering column while
recalling the exit position, the recall may stop. Remove the obstruction; then press and hold the
appropriate manual control for the exit feature not recalling for two seconds. Try recalling the exit
position again. If the exit position is still not recalling, see your dealer for service.
This information replaces the information located under “Exterior Lamp Controls” found in Section 6
of your owner manual.

Automatic High-Beam System
The automatic high-beam feature is not available on this vehicle.