ATTENTION:
GENERAL MANAGER

q

PARTS MANAGER

q

CLAIMS PERSONNEL

q

IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.

SERVICE MANAGER

q

© 2023 Subaru of America, Inc. All rights reserved.

SERVICE BULLETIN
APPLICABILITY:
SUBJECT:

2023MY Forester

NUMBER: 09-104-23R
DATE: 05/09/23

Reprogramming Files / P0011 & P0023

REVISED: 10/12/23

INTRODUCTION:
This bulletin announces availability of reprogramming files for the Engine Control Module (ECM)
to address rare cases of DTCs P0011 (“A” Camshaft Position – Timing Over-Advanced or System
Performance Bank 1) and P0021 (“A” Camshaft Position – Timing Over-Advanced or System
Performance Bank 2) detected by the ECM. The new files contain enhanced logic to optimize the
detection parameters of DTCs P0011 & P0023. If these DTCs are detected by the ECM, reprogram
the ECM using the procedures outlined in this bulletin.
PRODUCTION CHANGE INFORMATION:
These files were incorporated into vehicle production as per the table below.
Model

Starting VIN

Forester

PH436177

PAK FILE APPLICABILITY:
Model

Forester

MY

File Description

Old ECU Part Number

Decryption
Keyword

New ECM CID Number

22765AS921.pak

22765AS920

CEC38943

XE1W052k00G

22765AS931.pak

22765AS930

95C2FE90

XE1W052z00G

23

These files are included in the April 2023 SSM software update.

CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.

Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.

Continued...
Bulletin Number: 09-104-23R; Revised: 10/12/23

Page 1 of 3

SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
•

Reprogram the ECM following the normal FlashWrite procedure.

Subaru of America, Inc. (SOA) highly recommends utilizing either the Subaru Midtronics DCA8000
Dynamic Diagnostic Charging System or the Subaru Midtronics GR8-1100 Diagnostic Battery
Charger to the vehicle in the Power Supply Mode feature anytime a vehicle control module is
being reprogrammed. Once the Midtronics charger is connected to the vehicle, if the battery is fully
charged, it will take less than three (3) minutes to boot-up the charger, select the Power Supply Mode,
and have the battery voltage stabilized and ready for reprogramming.
NOTES:
•

For instructions on using the Power Supply Mode, reference the applicable User Manual for
the Midtronics DCA-8000 Dynamic Diagnostic Charging System and the Midtronics GR81100 Diagnostic Battery Charger on STIS.

•

Confirm all electrical loads such as lights, audio, HVAC, seat heaters, and rear defroster are
allswitched OFF before setting up the charger for Power Supply Mode.

•

Select the correct battery type (Enhanced Flooded, Flooded, Gel, AGM or AGM Spiral).

•

Input the CCA which matches the vehicle’s battery. NOTE: OE and replacement batteries
have different CCA ratings. Always confirm the battery’s CCA rating before proceeding.

•

If using a DCA-8000 Dynamic Diagnostic Charging System, set the power supply voltage to
13.5 Volts.

•

DO NOT connect the DST-i or DST-010 until the Power Supply mode function has completed
its battery test mode and the Charging Voltage has dropped to and shows a steady 13.5 Volts
on the display.

•

Once Power Supply Mode reaches a steady 13.5 Volts, connect the DST-i or DST-010 to the
OBD connector and proceed with initiating the normal FlashWrite reprogramming process.

•

Amperage will fluctuate based upon the vehicle’s demand for power. NOTE: If the voltage
rises beyond 14 Volts while programming is in process, the procedure will abort. This can
indicate a need to test or charge the vehicle battery before any further attempt at programming
is made.

•

ALWAYS set the power supply voltage to 13.5 Volts when using Power Supply Mode.
NEVER turn the ignition switch on when charging at voltages 15 Volts or higher.

REMINDER: If the DCA-8000 or GR8-1100 indicates the vehicle’s battery must be charged, charge
the battery fully before proceeding to reprogram the vehicle while using the Power Supply Mode.
Continued...
Bulletin Number: 09-104-23R; Revised: 10/12/23

Page 2 of 3

NOTE: Control module failures resulting from battery discharge during reprogramming are not a
matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose
per the procedure outlined in the applicable Service Manual.

VERY IMPORTANT:
This information is applicable to the Subaru Midtronics DCA-8000 Dynamic Diagnostic Charging
System and the Subaru Midtronics GR8-1100 Diagnostic Battery Charger ONLY. It does not apply to
any other brand / type of “generic” battery charger whatsoever. ONLY the DCA-8000 and the GR81100 and their Power Supply Mode feature have been tested and approved by SOA.

WARRANTY / CLAIM INFORMATION:
For vehicles within the Basic New Car Limited Warranty period, this repair may be submitted using
the following claim information:
Labor Description

Labor Operation #

Fail Code

Labor Time

MFI OBDII ECM Reprogramming

A455-288

UPG-48

0.4

IMPORTANT: Always note the original Calibration Identification number (CID) the vehicle came in
with on the repair order before reprogramming and, make sure to list the NEW CID for any newlyinstalled programming (as confirmed from the actual control module AFTER installation). The
NEW CID MUST also be noted on the repair order as this information is required for entry in the
Miscellaneous Detail field during claim submission.

NOTE: The PAK file listings provided in this bulletin are the latest available at the time of
publishing. Updates are often released thereafter without revision to the original bulletin. For this
reason, it is critical to always have the latest version of Select Monitor software installed on your
system. You can confirm if a later version is available by entering the CID listed in this bulletin into
FlashWrite. If a newer CID is shown as available in FlashWrite, reprogram using that file.

IMPORTANT REMINDERS:
•

SOA strongly discourages the printing and/or local storage of service information as previously
released information and electronic publications may be updated at any time.

•

Always check for any open recalls or campaigns anytime a vehicle is in for servicing.

•

Always refer to STIS for the latest service information before performing any repairs.

Continued...
Bulletin Number: 09-104-23R; Revised: 10/12/23

Page 3 of 3