02-06-2015

2015

Passenger footpeg or
floorboard touches
lateral panel when in
raised position

No Case needed

The passenger footpeg or floorboard can contact the
lateral panel when raised in the upward position. This
can cause lateral panel paint scratches or blemishes.

Passenger Fooipeg Contacts Lateral
Panel

2015

1330
Engine

Overheating at PDI or
shortly afler

Was the coolant bottle
level wilhin min/max?
Do the hoses all get
hot? If not which ones
(upper or lower hoses
of radiator}?

A few 1330 engines may have nat been bled properly
during the assembly process causing air lo be trapped in
the cooling circuit. This will cause the unit to overheat
within a few miles,

Perform the bleeding procedure 2 times as decribed in
the shop manual, Wilh engine cold, remove the coolant
boltle cap, start engine and let itidle until the rad fans
stant, turn off engine and let it cool down completely.
Adjust coolant level. Do ihe heat cycle again. When
engine has cooled down the 2nd time, adjust the coolant
level in the bottle and install cap.

Regular warranly applies.

14-07-2015

2015

Laleral panel
unclipping from fuel
tank cover

No Case needed

The lateral panels of the F3 may unclip from the fuel tank
cover when pressing on the fuel tank cover or front
portion of the seat.

Lateral Panel Unclipping From Fuel
Tank Cover

30-03-2015

https:/br p--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gm sy &lang=#googtrans(enjen)

This is caused by the front fender rear support. In some
cases it may have been produced with more offsel giving

2s

10/2/2016 https://brp--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(en|en)
this deviation, This can happen of RH or LH fenders.
2015 | All Front fender devialion No Case needed 2015 LH front fender
You can replace the front fender rear support under PDI
or regular warranty.
Consult Community post linked.
On a few F3 units the handlebar commodo (multi-
function switches) may rolate, this is due to the
handlebar end clamp not being fully torqued. Simply
jue the clamp bolts to 11.41.Nm,
Handlebar commodo
2015 | F3 movement-clamp not | No Case needed 11-02-2015
torqued enough
From the 1st reports of this concern BRP confirms this is
Ignition switch cover by design at the present lime,
BRP will work on a design change to remedy the -
am : . pI -02-
2015 | F3 (bezel) moves No Case needed situation. At the present time, part replacement will not Video example 41-02-2015
sideways i
resolve the issue.
See linked video for more precision.
Recently BRP has changed its crate design to have a
tarp installed at the bottom lo ensure full
. enclosure. Unfortunately a small number of F3 units were
Crate damage caused | Pictures of damaged ‘ . ve
2015 | F3 by road debris and areas and general or will be delivered before this improvement was . F3 Possible Corrosion Issue 04-03-2015
: . a . implemented meaning that depending on the location of. | eeeeeeerereerroao
calcium corrosion condition of the unit. . an
the crate on the transport a F3 unit may arrive in a
condition which requires cleaning. Refer to the
Community post linked here for details.
Important TSTs and Articles
MY | Model Title Type Comment Date Added
Let's understand that the F3 cross country saddlebags (219400696) were not designed {o be
2015 | £3 SADDLE BAGS ON THE Community waterproof but waler resistant. There is a difference in these terms: 43-10-2015
F3-Water/Dustinfiltration | Post ¢ Water-resistant: able to resist the penetration of water lo some degree but not entirely
e Waterproof: impervious to water
F3 unloading from As everyone anticipates lhe arrival of the F3 models al your dirships please share the following
transport fork liftneeds Community | information with your service crew and persons in charge of unloading units from the transport
2015 | F3 10-02-2015
48 inch long forks Post truck,
mininurr Itis recommended to use minimum 48 inch long forks in order to correctly reach across the crate.
As a general rule of alignment we want to make sure the unit's ride heightis properly adjusted.
F3 Perform front shock Communi neat is ride nejghtyou ask? ms is me suspension seting which places the steering geometry in
2015 | ST preload adjustment to zoe nity | the “sweet spot" and is lease affected by bump sleer. 10-02-2015
RS _| avoid handling issues Units with front FOX shocks can be adjusted
Refer to linked post......
2015 F3 (Table of . This manual has been prepared as a guide to correctly service and repair 2015 Can-Am roadsters. .
2015) F3 | Content) Shop Manual | Atle PIN: 219100799 18-11-2014
2015 RT (Table of TABLE OF CONTENT Roadster Shop Manual Supplement MY 2015. P/N: 219100798. This SHOP
2015 | RT 2015 RT (Table of Article MANUAL SUPPLEMENT must be used in conjunction with the appropriate SHOP MANUEL. Refer | 18-11-2014
Content) - Shop Manual ‘ . ae
to the proper manual when a particular system is not covered in this supplement.
2015 | F3 Wiring Diagram Article 18-11-2014
2015 | RT Wiring Diagram Article 18-11-2014
2015 {Table of Content) - . This publication governs all warranty labor allowances for Can-Am Roadster Spyder models.
2015)/)/ All Flat Rale Article Subject to review from time to time, without notice or delay. 20-11-2014
2015 | RT Cluster Remains Active TST IF lhe accessory fuses F6 and F7 are both installed at the same time the Cluster will remain powered 07-11-2014
With Key Off even when the key is off.
MY Model Title Comment
Refer to B.U.D.S. Directory for all information related to B.U.D.S.
Download Current Version
https://br p--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(en|en) 3/5

10/2/2016 https://br p--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(enjen)
2015 All i _ Updates for Database
B Dir R ds Related Downloads
Related Articles
Warranty and Service Bulletins
MY | Model Title Type Comment Date Added
2015 | all 2015-1 New ECO Crates Service To reduce its impact on the environment and the costs for the dealers, BRP will now use new 14-05-2014
a shipping crates,
The Predelivery Check List (PDI Check List) must be used in conjunction with the Predelivery
2015-2 Importance Of Bulletin applicable to the vehicle.
-2 Imp . -07-
2015 | All Predelivery Check List Service It is mandatory for the dealer to complete the PDI Check List. 15-07-2014
The customer must read, fill and sign the PDI Check List.
2015-3 Batlery Activatio As a reference to pre-delivery inspection bulletin, this service publication provides instructions
2015 | All Charging and Mai vienannce Service | for the activation, charging and mainlenance of new Roadster batteries. It contains standard 18-07-2014
: practices and can be used as a reference for preparing vehicles before delivery to customers.
2015 | All 2015-4 Paint Codes Service | These paints should be used for minor touch-ups only. 15-10-2014
BRP is introducing a new MPI-3 inlerface card to replace the current MPI-2 card, which will
conlinue to function on all BRP vehicles.
MPI-3 card improvements over the MPI-2 card are:
- Amore robust casing
— A faster processor significantly reducing ECU reprogramming time
— An external DBS resistor that can be added or removed from the MPI-3 interface card,
Multi-Brand (201s) New MPI-3 - improving connectivity on all BRP vehicles. 49-
2015 |All Interface Card Service NOTE: The MPI-2 card had a resistor built into it. However, on newer vehicles, this resistor is 18-12-2014
already
included in the vehicle harness. Since having the extra resistor could cause communication
issues, it
has been designed as a separate unit of the MPI-3. For specific vehicle application, consult
the latest
BRP B.U.D.S. CHART,
2015 | F3 2015-5 Change of Torque for Service Please note that the tightening torque has been lowered due to possible damages to 01-2015
Handlebar Clamp handlebar clamp.
2015 | All 2015-6 Alignment Specificatians | Service | All Roadster alignment information has been categorized in (his service bulletin, 41-03-2015
2013-] RS 2015-7 New Evap Purge Valve - As an improvement to the evaporative emission system (EVAP), BRP just released a new
~ Service . : 27-08-2015
2015 | ST Line Execution EVAP purge valve line execution.
FS 2015-1 Oil Sweating from Clutch | Warranty | The HCM wiring harness nuton top of the SE6 clutch cover may not have been properly
2015 | RT . : : . : : . 11-02-2015
SEG Cover HCM Connector Bulletin | tightened during assembly. This may lead to oil sweating past the o-ring.
2015-2 Rear Brake Hose Might
2015 | F3 be in Contact with Muffler Warranty | The rear brake hose might be in contact with the muffler support and/or the hose adapter 26-02-2015
Support or Pin en Tandem Bulletin retaining pin on the tandem master cylinder (TMC) of the brake system.
Master Cylinder
PAC . . .
2015-3 Loose Passenger The Detachable Passenger Backrest sold in (Kit P/N : 219 400 499) for the Roadster F3
2015 | F3 Warranly - naar 02-04-2015
Backrest bulletin models, was assembled wilhout lhreadlocker on the indicated screws.
2015-4 Knock Sensor Harness Warranly | The knock sensor harness may melt if rouled too close of the exhaust manifold heat shield, A
2015 | F3 : : 30-04-2015
Incorreclly Routed Bulletin | melted harness would lead to a limp home made.
Quality PROBLEM
2015-5 Insufficient Parking Brake The parking brake motor may not apply/hold enough tension on the brake cable. |
2015 | RT Cable Tension When Applied waranty SOLUTION 09-07-2015
Replace the parking brake motor wilh the REQUIRED PART.
The hood stripe decal does not meet our quality standards.
When installed, the hood stripe decal may peel, wrinkle and/or bubble.
PAC
- ip . . -|
2015 ) FS 2015-6 F3 Hood Stripe Decal arranty Return all decals in stock of the following part numbers to BRP, and order new ones, 07-2015
If owners complain about esthetic issues of these decals, replace them at no cost to the owner
and submita claim for part and labor.
Alimiled quanlity of vehicles were shipped wilh liquid contaminants in the gearbox posilion
sensor (GBPS) housing thal will damage the sensor.
A damaged GBPS may lead to; P-codes, limp home mode aclivation or vehicle does not shift.
Unit will have shifting issues, stuck in gear, "E” displayed in cluster.
List of usual codes seen:
53 2015-7 Gearbox Position S W P2801 Gear position sensor invalid range
- arbox Positi r
2015 | pF oe eee osTion Senso Balen P2806 Gear position sensor angle defined area vs position not plausible 21-07-2015
P074D Unable lo Downshift 3 Times In a Row
P284D Nolintended downshift detected
P284E Not inlended upshift delecled
P284F Downshift Delected on Upshift request
P284F Not Intended Shift Delected From N --> 1 or R --> 1

https ://brp--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(enlen)

4/5

10/2/2016 https://brp--c,na13.visual force.com/apex/Article_Detall_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(en|en)
P2850 Upshift detected on upshift request
PROBLEM
A crack around the welding of the rear shock absorber upper bracket could develop.
SOLUTION
2015-9 Spyder F3 - Installation Of | Warranty | Install the chassis reinforcement to hall or prevent a crack propagation along the frame
2015 | F3 . ri . 42-01-2016
The Chassis Reinforcement Bulletin | section.
In addition, BRP will extend the warranty for the chassis. Refer to WARRANTY section for
more information.
Training
MY Model Document Description Hyperlink Revised Date
2015 | F3 2015 Technical presentation Link 25-09-2014
Attachment:

First Published By: Dany Davey on 2015-02-03
Last Modified By: Dany Davey on 2016-01-29

https://brp--c.na13.visual.force.com/apex/Article_Detail_TST_Print?id=kA8a0000000Gmsy&lang=#googtrans(en|en)

5/5