Classification:

EM15-001

Reference:

Date:

NTB15-020

March 17, 2015

2013-2014 SENTRA;
ENGINE OVER TEMP, DTC P1217, AND / OR A/C NOT COLD

APPLIED VEHICLE: 2013-2014 Sentra (B17)

IF YOU CONFIRM:




The engine has an over temp condition.
The radiator fan does not operate.
The 40A fusible link for the fan shroud and motor assembly (cooling fan or
radiator fan) is open or has no continuity.
NOTE:
 The MIL may be ON with DTC P1217 (ENG OVER TEMP) stored in the ECM.
 The customer may state the A/C does not produce cold air as defined in the
Electronic Service Manual.

ACTION:
1. Compare the vehicle’s current ECM part number to those listed in Table A
(see page 6).
2. If the ECM part number matches one listed in Table A, reprogram the ECM.
3. Replace the 40A fusible link.
4. Replace the fan shroud and motor assembly (cooling fan/radiator fan).
5. Inspect the engine room harness, replace as necessary.
6. Verify cooling system operation and related engine condition.

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work
you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians
are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/12

SERVICE PROCEDURE
1. Replace the 40A fusible link.


Refer to the Electronic Service Manual (ESM), section PG-Power Supply, Ground
& Circuit Elements, for 40A fusible link location.

2. Replace the radiator fan.


Refer to the ESM, section CO-Engine Cooling System, for radiator fan (cooling
fan) removal and installation.

3. Inspect the engine room harness going to the radiator fan for an over temp condition.


Replace the engine room harness as needed.

4. Top off the cooling system.


Refer to the ESM, section CO-Engine Cooling System, for filling the cooling
system.

5. Verify the radiator fan cycles on and off with the engine idling and the radiator fan
comes on when the A/C is turned ON.
6. Verify the engine is operating normally (for example, the head gasket is sealing and not
leaking).


Refer to the appropriate section(s) of the ESM.

Go to the next page.

2/12

NTB15-020

ECM Part Number Check / Reprogramming
NOTE:


Most instructions for reprogramming with CONSULT-III plus (C-III plus) are
displayed on the CONSULT PC screen.



If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT-III plus (C-III plus) Reprogramming" general procedure.



Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learn (IAVL) conditions:

 Engine coolant temperature: 70 -100°C
(158 - 212°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up
Figure A


After reprogramming is complete, you will be required to perform Throttle Valve
Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC
erase.

CAUTION:


Connect the GR8 to the vehicle 12 volt battery and set to ECM power supply
mode. If the vehicle battery voltage drops below 12.0V or rises above 13.5V
during reprogramming, the ECM may be damaged.



Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.



Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.



Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the VI. If Bluetooth® signal waves are within
range of the CONSULT PC during reprogramming, reprogramming may be
interrupted and the ECM may be damaged.

3/12

NTB15-020

1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

2. Open C-III plus.

3. Wait for the plus VI to be recognized.


Serial number will display when the plus VI is recognized.

4. Select Re/programming, Configuration.

Step 3:
plus VI is
recognized

Step
4

Figure 1

5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in
Figure 2 on the next page.

4/12

NTB15-020

6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).

xxxxxxxxxxxxxx

6A: Current ECM P/N
xxxx
xxxxxxxxxxxxxx
xxxxxxxxxxxxxx

Figure 2

B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table A on the next page.


If there is a match, the ECM needs to be reprogrammed. Continue with the
reprogramming procedure.



If there is not a match, ECM reprogramming does not apply. Repairs are
complete.

5/12

NTB15-020

Table A
Model

2013 Sentra

Current ECM Part Number: 23710 3SA0A, 3SA0B, 3SA0C,
3SA0D, 3SA0E
3SA2A, 3SA2B, 3SA2C,
3SA2D, 3SA2E
3SA4A, 3SA4B, 3SA4C,
3SA4D, 3SA4E
3SA5A, 3SA5B, 3SA5C,
3SA5D, 3SA5E
3SA6A, 3SA6B, 3SA6C,
3SA6D, 3SA6E
3SB0A, 3SB0B, 3SB0C, 3SB0D
3SG2A, 3SG2B, 3SG2C, 3SG2D
3SG3A, 3SG3B, 3SG3C,
3SG3D, 3SG3E
3SG6A
3SG7A
3SR2A
3SR3A
9AM0A, 9AM0B
9AM1A, 9AM1B

2014 Sentra

9AM2A, 9AM2B
9AM3A, 9AM3B
9AM4A, 9AM4B
9AM5A, 9AM5B

6/12

NTB15-020

7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.

NOTE:


In some cases, more than one new P/N for reprogramming is available.
 In this case, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.



If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle.

xxxxx-xxxxx

xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

xxxxx-xxxxx

xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

Figure 3

7/12

NTB15-020

8. When the screen in Figure 4 displays, reprogramming is complete.

NOTE: If the screen in Figure 4 does not display (reprogramming does not complete),
refer to the information on the next page.

9. Disconnect the battery charger from the vehicle.

10. Select Next.

Step
10

Figure 4

NOTE:


In the next steps (page 10), you will perform Throttle Valve Closed Position, Idle Air
Volume Learn, Accelerator Closed Position, and DTC erase.



These operations are required before C-III plus will provide the final reprogramming
confirmation report.

8/12

NTB15-020

ECM Recovery
Do not disconnect plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:


Check battery voltage
(12.0 –15.5 V).



Ignition is ON, engine OFF.



External Bluetooth® devices
are OFF.



All electrical loads are OFF.



Select retry and follow the
on screen instructions.



“Retry” may not go through
on first attempt and can be
selected more than once.

Figure 5

If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:


Check battery voltage
(12.0 –15.5 V).



CONSULT A/C adapter is
plugged in.



Ignition is ON, engine OFF.



Transmission is in Park.



All C-III plus / VI cables are
securely connected.



All C-III plus updates are
installed.



Select Home, and restart
the reprogram procedure
from the beginning.

Figure 6

9/12

NTB15-020

11. Follow the on-screen instructions to perform the following:


Throttle Valve Closed Position



Idle Air Volume Learn (IAVL)

NOTE:
 Listed below are common conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of
range.
 Refer to the appropriate Electronic Service Manual (ESM) for specific
conditions required for the vehicle you are working on.
o
o
o
o
o
o
o

Engine coolant temperature: 70 -100° C (158 - 212°F)
Battery voltage: More than 12.9V (At idle)
Shift selector: P or N
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed up



Accelerator Pedal Close Position Learning



Erase DTCs

Continue to the next page.

10/12

NTB15-020

12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty
documentation.
15. Select Confirm.

xxxxx

Step
13

xxxxx
xxxxxxx
xxxxxxxxxxxxxxxxx

Step
14
xxxxxxxxxxxxxxxxx

Step
15

Figure 7

16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
19. Make sure the vehicle operates correctly and the MIL is OFF.


If the MIL comes ON, go back to ASIST for further diagnostic information.



Diagnosis and repairs beyond this bulletin (ECM reprogramming, radiator fan
replacement, etc.) are not covered by this bulletin.

11/12

NTB15-020

PARTS INFORMATION

*
**

DESCRIPTION

PART NUMBER

QUANTITY

MOTOR & FAN ASSY-W/ SHROUD
CONNECTOR ASSY-FUSIBLE LINK

21481-3SH5A
24370-C9922

1
1

Nissan Genuine Blue
Long Life Antifreeze/Coolant

999MP-L25500P

**

Engine room harness

24012-xxxxx *

1 ***

Use FAST or your Electronic Parts Catalog to obtain the correct part number.

Up to one (1) gallon. Nissan Genuine Blue Long Life Antifreeze/Coolant is available
through the Nissan Maintenance Advantage program: Phone: 877-NIS-NMA1
(877-647-6621), or Website order via link on dealer portal www.NNAnet.com and
click on “Maintenance Advantage” link.
***As needed. The part must be verified as needing replacement.

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE SYM
DIA
FRT
Replace cooling fan
Replace fusible link

CC20AA
23703-3SA1A

RA10AA

ZE

32

(1)

Reprogram ECM
DE97AA
(1) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.

AND - IF NEEDED - on the same repair line
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE SYM
DIA
FRT
Replace engine room harness
23703-3SA1A
RA16AA
ZE
32
(1)
(1) This is a Straight Time operation code claim only for actual repair time used based on
time stamps for this portion of the repair only.

12/12

NTB15-020