Check function of “AUX,” USB, and SD card inputs (if equipped)

D

Vehicles Equipped with Rear Entertainment System (if equipped):
Confirm operation of DVD player, remote control and infrared wireless headphones.

9. HANDS-FREE TELEPHONE (if equipped).
For Lancer badged vehicles, Outlander, and Outlander Sport/RVR, control switches for the
hands-free system are located on the steering wheel if the vehicle is pre-wired for hands-free
operation. For these models, this does not mean the vehicle is hands-free equipped. Refer to the
Monroney label to determine if the vehicle is equipped for hands free telephone use.
To check proper hands-free function on vehicles without MMCS, press the SPEECH button. You
will receive an audible response advising the system is connected and ready. Say “CANCEL” to exit.
To check proper hands-free function on vehicles with MMCS, press the SPEECH button for at least
two second. You will receive an audible response advising the system is connected and ready. Say
“CANCEL” to exit.
10. OPTIONAL MITSUBISHI MULTI-COMMUNICATION SYSTEM (MMCS).
a. To check proper hands-free operation, press the OK button on the MMCS start-up screen and
press the SPEECH button for one second. You will receive an audible response “Please speak
after the beep”. The following voice commands can be used:
(1) “AM” - System Response: “AM, Receive AM”
(2) “FM” - System Response: “FM, Receive FM”
(3) “Map” - System Response: “Display Current Location”
b. Make sure the navigation screen displays your location when the NAVI button is pressed.
NOTE: The navigation system and satellite radio may not operate properly if the vehicle is
in an enclosed area. This includes being surrounded by tall buildings. The default location
for both units is New York, NY. If this is not your location, move the vehicle to an open area
with a clear view of the Southern sky and recheck.
11. REAR-VIEW CAMERA SYSTEM (if equipped).
Shift into reverse. Confirm the camera image is clearly displayed on the audio screen.
12. PASSENGER AIRBAG AND SEATBELT LIGHT FUNCTIONS.
Sit in the front passenger seat and verify the passenger airbag light goes out. Verify the passenger
seat belt reminder light comes on when the seat belt is unfastened, and goes off when it is fastened.
13. WINDSHIELD WIPER DE-ICER (if equipped), REAR WINDOW DEFOGGER AND HEATED
DOOR MIRROR (if equipped).
Check with the engine running. Turn the windshield wiper de-icer (if equipped) and rear window
defogger on, allow time for the windshield wiper de-icer, rear window and mirror elements to warm
up and check them during the walk around inspection. Place your hand on the windshield wiper
de-icer, rear window defogger and heated door mirrors (if equipped) to ensure they are heating. Be
sure to turn off the windshield wiper de-icer and defogger after checking.
14. Turn the ignition switch to the “OFF” position.

Page 8 of 23
TSB−16−00−001

C. WALKAROUND INSPECTION
Before starting this section, make sure the ignition switch is “ON” (ensure the engine is OFF) and place
the transmission selector in “R” (reverse) with the parking brake applied. DO NOT START THE ENGINE.
1. Check EXTERIOR LIGHTS.
Ensure ALL exterior lights, including stoplights, function properly. Check for chipped or cracked
lenses. Verify the AUTO-OFF headlights function properly (refer to the Service Manual for checking
procedures).
2. Check Rain Light Sensor (if equipped).
a. With the headlight switch in the AUTO position, cover the sensor with a thick material (like a fender
cover) and confirm headlight operation. Uncover the rain light sensor.
b. With the wiper switch in the AUTO position, confirm wiper operation when water is sprayed on the
upper center of the windshield.
Be sure to shift to “P,” turn ALL lights off, and turn the ignition switch to the “OFF” position after
completing the inspection .
3. REMOTE KEYLESS ENTRY (RKE) or FREE-HAND ADVANCED SECURITY TRANSMITTER
(F.A.S.T.) SYSTEM, THEFT ALARM SYSTEM, ALL DOOR LOCKS, LATCHES, ONE-TOUCH
START SYSTEM (O.S.S.) & IMMOBILIZER.
Multi-function Key with RKE (if equipped)
Check the door and trunk (if equipped) locking and unlocking features.
Ensure the key is removed from the ignition. Close all doors and trunk.
D Use all keys to manually lock and unlock the driver's door and trunk/liftgate (if equipped).
D Press the “lock” button once to lock all doors.
D Pressing the “unlock” button once unlocks the driver's door, and pressing it a second time
within 2 seconds unlocks the other doors and the liftgate (if equipped).
D For remotes with 3 buttons, press the “trunk” button twice to open the trunk. Press the
“Panic” button (if equipped) for 2 seconds to test the panic alarm. Press again to turn off the
panic alarm.
NOTE: Factory-installed RKE systems can be customized for various “answerback” responses,
depending on the model and system installed. Ensure the vehicle's answerback feature is in the
full-function answerback mode, where both the horn and parking lamps signal when the doors are locked,
and the parking lamps signal when the doors are unlocked. Refer to the vehicle Owner's Manual for
programming information.

F.A.S.T. Key (if equipped)
a. Ensure door locks operate using the buttons on the F.A.S.T. key.
b. Ensure door locks operate using the lock/unlock button located on the outer driver's door handle
and the outer front passenger's door handle.
NOTE: The default for the F.A.S.T. Key system unlocks only the driver's door when pressing the button
located on the outer driver's door handle and all doors when pressing the button located on the
outer front passenger's door handle.

Theft Alarm (if equipped)
a. Lower the driver's window. Turn the ignition OFF and remove keys or transmitters from the
vehicle.
b. Exit the vehicle, close all doors and lock them using the transmitter. The security indicator on the
instrument panel remains lit for about 20 seconds and then blinks slowly when armed. For
F.A.S.T. key equipped vehicles, the transmitter must be more than 3 ft / 1m from the vehicle.

Page 9 of 23
TSB−16−00−001

c.

Reach through the open window, manually unlock the door, then open it (vehicles with F.A.S.T.;
hold the transmitter at arm's length away from the vehicle). The alarm should sound and the
headlights should flash.
TO DEACTIVATE THE ALARM:
Press the unlock button on the transmitter, or turn the ignition switch to the ACC or ON position
(transmitter must be present if equipped with F.A.S.T.).

d. Repeat steps a. through c. on the front passenger's door and lock.
e.

Repeat steps a. through c. using the trunk remote release and trunk lock (if equipped).

f.

Repeat steps a. through c. on the hood release.

Door Locks and Latches:
Close each door to check the latch and lock mechanisms. If adjustments are required, refer to the
appropriate Service Manual. Submit a warranty claim for any adjustment performed.
Child Safety Door Lock Operation:
Rear doors should not open from inside when the locking lever (located on the inside rear area of the
door near the latch mechanism) is in the LOCK position.
NOTE: Set the lever to the unlock or “FREE” position when you finish.

Fuel Filler Door/Filler Cap:
D

Pull the remote fuel door release lever and make sure it opens.

D

Check fuel filler cap operation to make sure it can be removed and installed with moderate effort.

D

Close the door and verify it latches properly.

4. REMOTE ENGINE START (if equipped).
Instructions for Remote Engine Start operation are kept in the glove box of equipped vehicles.
a. Remove the key from the ignition (without F.A.S.T.), close all doors, hood and the trunk (liftgate).
b. Start the engine using the remote transmitter.
c. Stop the engine using the remote transmitter.
d. Open one door and confirm the engine will not start with the remote transmitter.
e. Open the engine hood and confirm the engine will not start with the remote transmitter.
f.

Close all doors, and trunk/liftgate. Start the engine using the remote transmitter. Open the driver's
door while the engine is idling. The engine should stop.

5. TRUNK/HATCH/LIFTGATE, TRUNK LIGHT AND TRUNK/CARGO AREA TRIM APPEARANCE.
Check for trunk/liftgate closing quality (make sure it closes easily). Fit should be uniform.
!

WARNING

Make sure there is sufficient clearance for the liftgate to fully open.
a. Check operation of the inside trunk release (if equipped).
b. Verify trunk light/cargo light (if equipped) comes on and all trim is installed properly.
c. Make sure the trunk lid/liftgate closes with normal effort.

Page 10 of 23
TSB−16−00−001

d. Vehicles equipped with optional power liftgate:
D Press the liftgate master button (located in the center console in front of the shift selector).
Confirm the liftgate only works with the master button in the ACTIVE position. Press the button
next to the license plate lamp to open the liftgate. When fully opened, press the close button
located to the left of the latch mechanism to close it. Confirm the liftgate latches securely.
Repeat with the dash mounted activation switch (lower dash, left of steering wheel).
D Open the power liftgate. While it is opening, stop it with your hand. With the liftgate fully open,
press the CLOSE button on the liftgate and stop its movement with your hand. It should return
to its previous position (closed or open).
6. EMERGENCY INSIDE TRUNK RELEASE HANDLE (if equipped).
Check the operation of the emergency inside trunk release handle. Open the trunk lid and trip the
latch by pushing on the catch with the shaft of a screwdriver to simulate trunk closure. Remove the
screwdriver with the latch in the closed position, and verify the release handle actuates the trunk
release. For more information about the Emergency Inside Trunk Release, refer to the vehicle's
Owner's Manual.
7. SPARE TIRE PRESSURE AND SPARE TIRE, JACK & TOOLS PROPERLY SECURED.
Spare Tire Pressure
Some models require removal of the spare tire for tire pressure adjustment. Check spare tire pressure
and make sure the spare tire is tightly secured after reinstalling it.
Jack & Tools
Check for jack and tools. For most cars and Outlander Sport/RVR, the tools and jack are in the trunk.
For Outlander: the tools and jack are behind the access panel in the right hand quarter trim.
Make sure all tools are properly secured and will not rattle or come loose. Refer to the Owner's Manual
for more information concerning jack and tool location.

D. UNDERHOOD
!! IMPORTANT !! Use fender covers to protect the vehicle body.
1. Check BATTERY charge using the Midtronics Battery Tester.
Make sure that battery cable terminals, and any additional wires attached to the terminals are tight.
Make sure the battery is secure.
Ensure the battery is fully charged (minimum 12.4 V). If necessary, follow Service Manual procedures
and recharge it. Remove the battery maintenance tag (if equipped) and insert it into the vehicle file
with other PDI documentation.
2. Check ENGINE OIL.
Check engine oil level. If oil is needed, check the the underhood label or appropriate Service Manual
for correct oil specifications.
3. Check BRAKE, CLUTCH, AND POWER STEERING FLUID.
D Check brake and clutch fluid levels using the scale on the plastic reservoir of both master cylinders
(brake and clutch). They should both be at the FULL mark. Add fluid as necessary.
NOTE: Use genuine Mitsubishi BRAKE FLUID, part number MZ311987.

D

Check power steering fluid (hydraulic power steering systems). It should be at the proper level
on the dipstick or the scale on the plastic reservoir.
NOTE: Use genuine Mitsubishi Power Steering Fluid, part number 4039645.

Page 11 of 23
TSB−16−00−001

4. Check COOLANT AND WINDSHIELD WASHER FLUID LEVELS.
Add fluid if necessary.
Coolant: Use only DiaQueen Super Long Life Coolant (genuine Mitsubishi COOLANT, part number
MZ320125).
Washer Fluid: Use genuine Mitsubishi Washer Fluid (part number ACH3ZC1X07).
5. Check for signs of FLUID LEAKS.
6. Check HOOD LATCH AND SAFETY CATCH.
Make sure the hood release lever pulls evenly and the hood cannot be lifted without releasing the
safety catch.
7. Check for LOOSE ATTACHMENTS.
Check for loose parts, wiring harness and cable clips and connections, incorrectly routed hoses and
harnesses, and insufficient clearance of components to moving engine parts.
8. EMISSION CONTROL EQUIPMENT.
The Environmental Protection Agency (EPA) requires this inspection.
Using the underhood label as a guide, verify all emission control equipment is installed.
NOTE: The EPA requires that dealers visually inspect the emission control devices prior to

delivery, or, as an alternative, inspect each vehicle for an illuminated malfunction indicator light
(MIL), and if the light is illuminated, diagnose and correct the malfunction.

E. UNDER VEHICLE
During PDI, every vehicle should be raised on a lift for under vehicle inspection. Refer to the appropriate
Service Manual for vehicle lift points.
1. Remove the BRAKE ROTOR PROTECTION (covers) (if equipped).
2. Remove SPRING SPACERS AND FRONT FASCIA PROTECTOR PLATE (if equipped).
3. Check for LOOSE ATTACHMENTS.
Make sure all wiring harness clips, brake pipe clips, heat shield fasteners and any other attachments
are properly secured.
4. Check for FLUID LEAKAGE.
Check for signs of leaks from engine components, transmission, fuel lines, coolant hoses, power
steering lines, and A/C lines (if equipped). Check lines for twists, kinks, proper routing and clearance
to moving parts.
5. ADJUST TIRE PRESSURE AND INSPECT TIRES FOR DAMAGE.
For tire pressure specifications, refer to the Tire Pressure and Loading label on the driver's side
B-pillar.
!! IMPORTANT !! On some models, the factory over-inflates the tires by 50% to prevent flat
spots during shipment and storage. It is critical to adjust tire pressures to the proper
specifications.
Check all tires for damage such as cuts, foreign objects in the tire, or any other imperfections.
Remove any tire pressure and/or tire balance decals from each tire if present.
NOTE: Low tire pressure on vehicles equipped with a Tire Pressure Monitoring System (TPMS) will illuminate
the TPMS warning light. With cold tires, adjust tire pressure on all vehicles to the specification shown on the
Tire Pressure and Loading Label. If a valve stem cap is missing, refer to Mitsubishi ASA CAPS and replace it
only with the part number quoted for the vehicle. Factory installed valve stem caps are designed to reduce
corrosion and damage to the valve. Refer to TSB-12-31-001 for additional TPMS information.

Page 12 of 23
TSB−16−00−001

F. ROAD TEST
*** IMPORTANT ***
RECALLS - Check the Warranty Superscreen for open recalls. Make sure any open recall is
performed BEFORE the vehicle is road tested.

Preliminary Road Test Notes

Figure 4

Warning and indicator lights vary by vehicle
and equipment.
Refer to the Owner's
Manual for a complete list for the vehicle.
Oil Pressure
Electronic Power Steering
Security

!

SECURITY

Vehicles should be at operating temperature prior to
performing the following checks. Before beginning the
road test, establish a route that you will use for every
vehicle. Recommended road test duration is at least 15
minutes and should include a variety of road conditions.
Record BEGINNING mileage
Record the beginning mileage of your road test on the
PDI form.
1. WARNING, INDICATOR LIGHTS, AND GAUGES.

Generator

a. Turn the ignition ON. The indicator and warning
lights shown in the illustration should illuminate (as
equipped).

Low Fuel Level

b. Fasten the driver's seat belt and start the engine.
Verify that all indicator lights go out, except the
passenger airbag light.

A/T Position Indicator
Seat Belt Reminder
Check Engine

SERVICE ENGINE SOON

or

c. Unfasten the driver's seat belt and verify the driver
seat belt reminder light comes on.
d. Open a door. Verify the door ajar light comes on.

ABS (Anti-lock
Brake System)
SRS (Supplemental
Restraint System)
High Beam
Door Ajar
A/T Temp (Automatic
Transmission Temperature)

S Passenger Airbag Light
S TPMS (Tire Pressure
Monitoring System) Light
FCM (Forward Collision
Mitigation) Light

e. The brake warning light should be lit when the
parking brake is applied.
f.

Verify all gauges and lights are working as
equipped.

g. Check operation of the seat belt warning buzzer
and the key reminder buzzer. For vehicles with the
F.A.S.T. Key system or O.S.S., move the
transmitter out of the vehicle and listen for a
warning tone.
h. For vehicles with Forward Collision Mitigation
(FCM), ensure the FCM light is displayed on the
MID when the engine is started. Use the FCM
button to toggle the following distance and confirm
the change is displayed in the MID.
i.

For vehicles with Lane Departure Warning (LDW),
ensure LDW is displayed on the MID when the
engine is started. Press and hold the LDW switch
to toggle it off, then repeat to turn it back on.

Page 13 of 23
TSB−16−00−001

2. AUTOMATIC TRANSMISSION (A/T) AND CONTINUOUSLY VARIABLE TRANSMISSION (CVT)
SHIFT INTERLOCK.
Make sure the shift lever can only be moved when the brake pedal is depressed and the ignition switch
is in the “ON” position. For vehicles with OSS, the engine must be running.
3. A/T / CVT STARTER INTERLOCK (if equipped).
Make sure the engine can be started ONLY when the shift selector is in PARK or NEUTRAL.
For vehicles equipped with O.S.S., the vehicle must only start if the brake pedal is depressed.
4. MANUAL TRANSMISSION (M/T) CLUTCH - STARTER INTERLOCK (if equipped).
Make sure the engine will start only when the clutch pedal is fully depressed.
5. CONDUCT A FULL ROAD TEST.
Drive the vehicle to identify dynamic symptoms that may need correction. Use the following
instructions as a guide.
!

WARNING

!

WARNING

!

WARNING

DO NOT ATTEMPT TO TEST THE COLLISION MITIGATION SYSTEM OR
ADAPTIVE CRUISE CONTROL FOLLOWING DISTANCE (if equipped).
Your route should be relatively free from traffic so you can safely conduct
the test and concentrate on vehicle operation and performance.
ALWAYS follow all traffic laws and safe driving practices. The PDI road test
should be conducted under a variety of different operating and road conditions.
Vehicles equipped with air conditioning: Place a thermometer in the center vent before beginning
your road test. This will be used later to check air conditioner operation.
6. A/T: Check A/T / CVT AUTO OPERATION.
a. From 25 mph (40 km/h), briefly accelerate at full throttle. The transmission should kick down to
1st gear, then shift to the higher gears. For CVT, the vehicle should accelerate smoothly.
b. Idle 20 seconds in “N” then shift to “D” then “R” holding each position for more than 3 seconds.
c. Check for smooth shifting during normal driving. Then upshift through all gears with 20% and 30%
throttle and decrease to a stop. On vehicles with Sportronic™ shift, slide the shift lever into “Sport
Mode” and manually upshift and downshift to verify proper operation.
d. Check paddle shift operation (if equipped). Ensure proper upshifts and downshifts.
7. M/T: Check CLUTCH AND M/T OPERATION.
Vehicles equipped with a manual transmission: Check for proper clutch operation and smooth
shifter/transmission operation. Repeatedly shift up and down at least 10 times at idle and at speeds
under 40 mph (64 km/h).
8. ALL WHEEL CONTROL (AWC) AND SUPER-ALL WHEEL CONTROL (S-AWC): Check
TRANSFER CASE OPERATION (if equipped).
Check for proper engagement and disengagement in all 4WD modes. For a detailed explanation of
changing drive modes, refer to section 3 of the Owner's Manual.
9. Check AWC MODE (including S-AWC) DISPLAY FUNCTIONS (if equipped).
Ensure the mode display changes (TARMAC, GRAVEL and SNOW) when toggling the mode switch.
10. Check ENGINE PERFORMANCE.
!

WARNING

ALWAYS follow all traffic laws and safe driving practices. Check engine
performance under the following conditions. The throttle should respond without hesitation.

Page 14 of 23
TSB−16−00−001

Part Throttle
At a constant speed of 25-35 mph (40-56 km/h), engine performance should be smooth, without
hesitation.
Under Load
Accelerate to 3/4 throttle. The vehicle should accelerate smoothly, without laboring or hesitation.
At Cruise
At a constant speed of 45-55 mph (75-90 km/h), engine performance should be smooth, without
hesitation or surging.
11. Check CRUISE CONTROL.
Cruise control switches are located on the steering wheel.
Control Functions
On/Off - Energizes and de-energizes the system and turns on the indicator light.
Coast/Set - Sets control speed. Also reduces set speed while engaged.
Acc/Res - Resumes previously set speed. Also increases set speed while engaged.
Cancel - Deactivates set driving speed.
!

WARNING

DO NOT ATTEMPT TO TEST THE ADAPTIVE CRUISE CONTROL (ACC)
FOLLOWING FUNCTION.
System Operation Check
NOTE: Cruise control will not operate below 25 mph (40 km/h).

a. Accelerate to 30 mph (50 km/h).
b. Turn on the ON/OFF switch. Make sure the CRUISE light illuminates.
c. Use the COAST/SET function to set the vehicle speed. The vehicle speed should hold at 30 mph
(50 km/h).
d. Increase the vehicle speed slightly by using the ACC/RES button momentarily.
e. Check each canceling function by depressing the brake, clutch (M/T only), and the CANCEL
button.
f. Resume the set speed by using the ACC/RES button.
g. Turn the cruise control off by pressing the ON/OFF switch.
Vehicles Equipped with ACC (if equipped)
Perform checks h-k in addition to those for standard cruise control (above).
h. Confirm the MID displays the screen for ACC when set (see Figure 5).
i. Confirm the Distance Scale toggles from Near to Far when the ACC Distance switch is pressed.
j. Press the ON/OFF switch to turn cruise control OFF.