L-SB-0051-18

Rev1

December 14, 2018

Floor Mat Installation During PDS
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2020

ES300H, ES350, GS F,
GS300, GS350, GX460,
IS300, IS350, LC500,
LC500H, LS500, LS500H,
LX570, NX300, NX300H, RC
F, RC300, RC350, RX350,
RX450H, UX200, UX250H

ADDITIONAL INFORMATION

REVISION NOTICE
October 09, 2020 Rev1:
 The Installation Procedure: Pre-Installed Knob Style section has been updated.
Any previous printed versions of this bulletin should be discarded.

Introduction

2020 model year Lexus vehicles are equipped with driver side floor mat retaining clips to secure
the floor mat in the correct position. In addition, some models may also utilize retaining clips for
passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate
Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat
floor mats to the vehicle carpet using the floor mat retaining clips.

© 2020 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 6

L-SB-0051-18

Rev1

December 14, 2018

Page 2 of 6

Floor Mat Installation During PDS
Introduction (continued)
CAUTION
 ALWAYS verify the floor mat is designed specifically for the model and model year it is being
installed in.
 ONLY use floor mats that can be secured using the retainers. ALL OEM Toyota floor mats are
specifically designed to fit correctly and be secured using the retainers.
 Make sure the floor mat is properly placed on the vehicle carpet and secured with the retainers.
If the driver side floor mat is NOT properly placed and secured, it could slip and interfere with
the movement of the pedals during driving and may cause an accident.
 Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance to
the mat.
 NEVER install more than one floor mat at a time in the driver’s seating position.
 If applicable, ANY secondary set of floor mats (based upon customer preference, such as the
all-weather floor mats or other floor mats) MUST be placed in the trunk with ALL the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Installation Procedures



Hook Style ................................................................................................................................. 2



Knob Style ................................................................................................................................. 4

Installation Procedure: Hook Style

1. Verify that the driver, and if applicable, passenger side and rear seat floor mats are for the
correct model and model year vehicle they are being installed in.

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-18

Rev1

December 14, 2018

Page 3 of 6

Floor Mat Installation During PDS
Installation Procedure: Hook Style (continued)

2. Attach the driver, and if applicable, passenger side and rear seat floor mats to the vehicle carpet
using the retaining clips.
3. Secure the mat by inserting the retaining clips through the grommet holes.
Figure 1.

3
1

2
1
2
3

1

Correct Installation

2

Retention Clip

3

Grommet

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-18

Rev1

December 14, 2018

Page 4 of 6

Floor Mat Installation During PDS
Installation Procedure: Hook Style (continued)

4. Verify proper installation.
NOTE
If applicable, do NOT remove the beige caution tag from the floor mat. ONLY the customer should
remove the caution tag.
Figure 2.

Installation Procedure: Pre-Installed Knob Style
NOTICE
If the vehicle is equipped with two sets of floor mats (carpet and all weather):
 Do NOT install both sets of floor mats at the same time.
 Install one set according to the current season and store the other set in the
luggage compartment.
 Discard the Floor Mat Safety Check insert for the installed set and keep the other with the spare
floor mat set for the customer’s reference.

1. Verify that the driver, and if applicable, passenger side and rear seat floor mats are for the
correct model and model year vehicle they are being installed in.

© 2020 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-18

Rev1

December 14, 2018

Page 5 of 6

Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Knob Style (continued)

2. Align the floor mat holes with the retention
clip knobs and place the floor mat holes onto
the retention clip knobs.

Figure 3.

1

2
3

3. Twist the retention clip knobs a quarter of a
turn to lock in place.

1

Retention Clip Eyelet on Floor Mat

2

Retention Clip

3

Front of Vehicle

Figure 4.

3

4. Verify the triangle marks on the retention
knobs and floor mat are aligned.

1

1

Twist Knob

2

Knob in Locked Position

3

Align Triangle Marks

© 2020 Lexus, a division of Toyota Motor Sales, USA

2

L-SB-0051-18

Rev1

December 14, 2018

Floor Mat Installation During PDS
Installation Procedure: Pre-Installed Knob Style (continued)

5. Verify proper installation.

Figure 5.

NOTE
If applicable, do NOT remove the yellow
caution tag from the floor mat. ONLY the
customer should remove the caution tag.

© 2020 Lexus, a division of Toyota Motor Sales, USA

Page 6 of 6