NHTSA ID Number: 10181340
Manufacturer Communication Number: SCB 11 M 041
TSB/Document Date: 2020-10-20
Summary
Vehicle software update to platform 10.2
Page | 43
Date released: 29 July 2013
Care Point: The Exhaust Valve Learn Routine is only required on vehicles that are fitted with the exhaust
valves.
93. Select the Exhaust Valve Learn Routine (14), followed by the arrow key (15).
15
14
94. The exhaust valve learn routine will now be performed.
95. Select Programme VIN (16), followed by the arrow button to proceed (17).
17
16
Page | 44
Date released: 29 July 2013
96. Press the stop/start button with the brake pedal depressed to start the engine and allow to idle until fully
warm.
Care point: The Air conditioning must be switched on and the engine coolant temperature must be above 80
degrees C before proceeding with the camshaft adaption procedure.
97. Select ECM (1), then Actual Values (2), select the following values as per the screenshot below (3), then
select the play button to access the required data screen.
98. The inlet and exhaust camshaft values should be between 1 and 4, both values will fluctuate slightly. If
all values are correct no further action is required proceed to step100. If any values are incorrect
proceed to step 99 to carry out the camshaft adaption.
2
3
1
99. Switch the engine off, wait 30 seconds, restart the engine and recheck the values. Repeat this procedure
until the target values are achieved.
Page | 45
Date released: 29 July 2013
Care point: The fuel level must be above ¼ before you proceed to the Diagnostic Module Leakage Test
(DMTL).
100.
Select Sequences (1), then DMTL-Diagnostic Module Leakage Test (2), followed by the arrow button
to proceed (3).
1
3
2
101.
Follow the preconditions and run the engine for 60 seconds and then select Ok (4).
4
Page | 46
Date released: 29 July 2013
102.
Follow the instructions on the next screen and then select Ok (5).
5
103.
The DMTL test will now run and can take up to six minutes to complete the 20 thou and 40 thou leak
test (6).
6
Page | 47
Date released: 29 July 2013
104.
When the 20 thou and 40 thou leak tests have compeletd the screen below will be dispalyed, then
select Ok (7).
7
105.
Page | 48
End the current MDS session to allow session feedback to be sent and stored at McLaren.
Date released: 29 July 2013
IRIS update
Care point: IRIS software downloads requires the vehicle to be in ignition state 5.
106.
Ensure the IRIS is powered up to the home screen and the radio is off.
Care point: The USB drive must be engaged with the gold contact points facing downwards.
107.
Insert the USB drive 11M2518CP.08 into the USB socket (1), then press and hold the centre IRIS
button for approximately five seconds until the McLaren logo screen appears. This will trigger the
software download process..
1
Page | 49
Date released: 29 July 2013
108.
The following screen will be displayed, select Update (2).
2
109.
The following software download screen will be displayed whilst the update is being carried out (3).
3
Page | 50
Date released: 29 July 2013
110.
Once the update has completed the following screen will be displayed (4), remove the USB drive.
4
Care Point: The system reboot can take up to three minutes and during this period the screen may appear
blank or contain lines.
111.
Once the reboot has completed the following screen will appear (5), select Dismiss (6)
5
6
Page | 51
Date released: 29 July 2013
112.
Press and hold the centre IRIS button for approximately five seconds until the McLaren
logo screen
appears to reset the unit and return normal functionality.
113.
Insert the USB drive 11M2433CP.03 in to the USB socket and the following screen will appear,
select Yes (7).
7
Care Point: The system reboot can take up to three minutes and during this period the screen may appear
blank or contain lines.
Page | 52
Date released: 29 July 2013
114.
Once the update has completed and the unit has rebooted, the following screen will be displayed (8),
select Dismiss (9) and remove the USB drive.
9
8
115.
Switch the Ignition off and wait until the Start/Stop button illumination has extinguished, wait a further
one minute and then establish the vehicle into ignition state 5 before following the next steps.
Care Point: Different level of Tuners will be supplied to dealers. Early level Tuners will require software
installation, later level Tuners do not. The different levels of Tuners can be seen in the pictures below and
should have been noted which level was fitted during initial installation.
Early level Tuner that REQUIRES software
installation
Page | 53
Date released: 29 July 2013
Latest level Tuner 11M2555CP.02 or
11M2555CP.03 that do NOT require
software installation
Latest level Tuner with Update
Complete label that does NOT require
software installation
Care point: If the vehicle has been fitted with an early level Tuner, read steps 123 to 125 and then return to
step 115 before you proceed with software installation. If a later level Tuner is installed proceed to step 127.
Page | 54
Date released: 29 July 2013
116.
Proceed to Home/Settings/About/Software and check the Tuner Firmware is displayed and does not
display UNKNOWN-UNKNOWN(10). If Ok proceed to step 123, If UNKNOWN-UNKNOWN is displayed
proceed to step 117.
10
117.
Switch the Ignition off and wait until the Start/Stop button illumination has extinguished, wait one
minute and then establish the vehicle into ignition state 5 before following the next steps.
118.
Re-check Tuner firmware level if UNKNOWN-UNKNOWN is no longer displayed proceed to step
123, if still displayed proceed to the next step.
119.
Press and hold the centre IRIS button for approximately five seconds until the McLaren logo screen
appears to reset the unit and the normal functionality will return.
120.
Re-check the Tuner firmware level if UNKNOWN-UNKNOWN is no longer displayed proceed to step
123, if still displayed proceed to the next step.
121.
Switch the Ignition off and wait until the Start/Stop button illumination has extinguished, wait two
minutes and then establish the vehicle into ignition state 5 before following the next steps.
122.
Re-check Tuner firmware level if UNKNOWN-UNKNOWN is no longer displayed proceed to step
123, if still displayed contact your RAM or Technical Support for further advice..
Page | 55
Date released: 29 July 2013
123.
Insert the USB drive 11M2531CP.03 in to the USB socket, the following screen will appear, select
Ok (11).
11
124.
The following screen will appear, select Ok (12).
12
Page | 56
Date released: 29 July 2013
125.
Once the update has completed the following screen will be displayed, remove the USB drive and
select Ok (13).
13
126.
The following screen will be displayed (13) and system will revert to the radio display after the tuner
has reset (14).
14
Page | 57
Date released: 29 July 2013
127.
EMMC Formatting and Navigation software installation is only required on vehicles built with
Meridian Surround Sound, if not required carry out steps 127 to 129 and then proceed to step 139.
128.
Select “SETTINGS” on the home screen to enter the settings menu (15).
15
129.
Hold down the IRIS mute button and perform the following actions by turning the volume control ring:
Right two notches on volume control
Left one notch on volume control
Right three notches on volume control
Left two notches on volume control
Page | 58
Date released: 29 July 2013
130.
An additional option “DEALER SETTINGS” will appear (16); select this option to enter the dealer
settings menu.
16
131.
Select “FORMAT EMMC” (17).
17
Page | 59
Date released: 29 July 2013
132.
EMMC Formatting in progress will be displayed (18).
18
133.
When the EMCC pop up disappears the formatting has finished.
134.
Press and hold the centre IRIS button for approximately five seconds until the McLaren logo screen
appears to reset the unit and to return normal functionality.
135.
Insert the USB drive that contains the Satellite Navigation software variant applicable to your market
(by referring to the software table on page 2), select Yes,(19)
19
Page | 60
Date released: 29 July 2013
136.
The following screen will be displayed (20).
20
Care Point: The system reboot can take up to three minutes and during this period the screen may appear
blank or contain lines.
137.
Once the update has completed and rebooted, the following screen will be displayed (21), select
Dismiss (22) and remove the USB drive.
22
Page | 61
21
Date released: 29 July 2013
138.
Press and hold the centre IRIS button for approximately five seconds until the McLaren logo screen
appears to reset the unit and return normal functionality.
139.
Repeat steps 127 to 129 on vehicles that have had Navigation software installed.
140.
Select the region you require to enable the correct radio frequency for (23), refer to Region
information below :WESTERN EUROPE:- Austria, Belgium, France, Germany, Great Britain, Italy, Monaco,
Netherlands, Spain, Sweden, Switzerland, Hong Kong, China, Australia, Singapore,
Bahrain, Kuwait, Qatar, Saudi Arabia, UAE (Abu Dhabi, Dubai), South Africa and
Lebanon.
NORTH AMERICA:- USA, Canada and Canada- Quebec.
REST OF WORLD:- Do Not select.
23
141.
Press and hold the centre IRIS button for approximately five seconds until the McLaren logo screen
appears to reset the unit and return normal functionality.
Page | 62
Date released: 29 July 2013
Care point: The VCI must be connected to the MDS with the USB cable to perform the next steps.
142.
Start a New MDS session in the MDS Offline mode, refer to Service Information Bulletin 11 S 011
McLaren Diagnostic System (MDS) Offline and proceed to complete the remaining procedures.
143.
Select ECM (1), then Actual Values (2), select the following values as per the screenshot below (3),
then select the play button to access the required data screen.
2
1
3
144.
Misfire adaptations are performed whilst the car is driven with the gearbox set to manual mode and
with the A/C off.
145.
Perform eleven successive fuel cuts from above 4000rpm for a 5 second duration (a fuel cut off will
occur when the accelerator pedal is fully released).
146.
Once the Fuel off Adaption Counter reaches 11, the Fuel off Adaption Finished Counter will display
1, the misfire adaptions have been learned. The Fuel off Adaption Counter will display Zero and then
start to count again when further fuel cut offs occur, this is correct operation and no further action is
required.
147.
Connect a mobile phone via Bluetooth and confirm functionality is Ok.
148.
The vehicle requires to be outside for the Satellite Navigation to locate the correct vehicle position on
the map this can take up to five minutes. Then enter a destination and drive the vehicle to confirm
functionality is ok.
Page | 63
Date released: 29 July 2013
149.
Insert the Owner Manual Supplements (1,2), IRIS User Guide (3) into the vehicles book set and
provide the customer with copies of the Model Year 2013 Upgrade Certificate (4) and the EU
Compliance document (5) (if applicable) .
1
Care point: The ‘Owners‟ Manual Supplement includes information relating to the new IEE OCS system
st
functionality. This system is not fitted to vehicles built prior to 31 May 2012. The customer should refer to
the main Owners‟ Manual should they require information relating to the OCS system on their vehicle.
2
Page | 64
Date released: 29 July 2013
Care point: The customer must be informed of the new functionality with the aid of the supplied owners‟
manual supplements.
3
4
5
Please contact your Regional Aftersales Manager should you have any questions relating to the information
contained in this bulletin.
Page | 65
Date released: 29 July 2013
WARRANTY INFORMATION
DESCRIPTION
RESOLUTION CODE
TOTAL REPAIR TIME
Software platform update
M0M30126A33A4A07
0.1
PARTS INFORMATION
PART
DESCRIPTION
PART NUMBER
QUANTITY
ORDER PROCESS
N/A
N/A
N/A
N/A
Page | 66
Date released: 29 July 2013
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: SCB 11 M 041
Replacement Service Bulletin Number:
MFR Communication Date: 2013-07-29
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.