GROUP
ELE

MODEL
2021MY
Seltos (SP2)

NUMBER
210

DATE
September 2020

TECHNICAL SERVICE BULLETIN
SERVICE ACTION: ICU OPERATION
LOGIC IMPROVEMENT (SA435)

SUBJECT:

This bulletin provides the procedure to improve the logic of the Integrated Central Control Unit
(ICU) on some 2021MY Seltos (SP2) vehicles, produced from November 20, 2019 through
August 13, 2020, which may exhibit a parasitic draw during long-term storage, while the ICU is
in Transportation Mode. To correct this concern, apply the improved logic to the ICU on
vehicles in dealer stock only, using the KDS ECU Upgrade function as described in this
bulletin. For confirmation that the latest reflash has been applied to a vehicle you are working
on, verify the ROM ID using the table on page 3 of this bulletin. Before conducting the
procedure, verify the vehicle is included in the list of affected VINs.

Kia Diagnostic System (KDS)

 NOTICE
A Service Action is a repair program without customer notification that is performed
during the warranty period. Any dealer requesting to perform this repair outside the
warranty period will require DPSM approval.
Repair status for a VIN is provided on WebDCS (Service → Warranty Coverage →
Warranty Coverage Inquiry → Campaign Information). Not completed Recall / Service
Action reports are available on WebDCS (Consumer Affairs → Not Completed Recall
→ Recall VIN → Select Report), which includes a list of affected vehicles.
This issue number is SA435.
Printed TSB copy is for reference only; information may be updated at any time.
Always refer to KGIS for the latest information.
Circulate To:

X General Manager


X Service Advisors


X Technicians


X Service Manager


X Parts Manager


X Body Shop Manager  Fleet Repair


Page 2 of 8
SUBJECT:

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

ECU Upgrade Procedure:
To correct this condition, the ECU should be reprogrammed using the KDS
download, as described in this bulletin.
Upgrade Event Name
507. SP2 ICU OPERATION LOGIC IMPROVEMENT

 NOTICE











A fully charged battery is necessary before ECU upgrade can take place. It is
recommended that a battery charger is used in ECU mode during reflashing or
the use of a fully charged jump starter box connected to the battery.
DO NOT connect any other battery charger to the vehicle during ECU upgrade.
Ensure the KDS or GDS is sufficiently charged prior to reflash.
All ECU upgrades must be done with the ignition key in the ‘ON’ position.
Be careful not to disconnect the VCI-II connected to the vehicle during the ECU
upgrade procedure.
DO NOT start the engine during ECU upgrade.
Do NOT turn the ignition key ‘OFF’ or interrupt the power supply during ECU
upgrade.
When the ECU upgrade is completed, turn the ignition ‘OFF’ and wait 10 seconds
before starting the engine.
ONLY use approved ECU upgrade software designated for the correct model and
model year.

 NOTICE
It is recommended to ALWAYS check the Electronic Parts Catalog (EPC) to locate
the ECU Part Number respective to Auto/Manual Mode ROM IDs. DO NOT reference
the parts label affixed to the ECU.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 3 of 8
SUBJECT:

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

 NOTICE
Before attempting an ECU upgrade on any Kia model, make sure to first determine
whether the particular model is equipped with an immobilizer security system.
Failure to follow proper procedures may cause the PCM to become inoperative after
the upgrade and any claims associated with this repair may be subject to
chargeback.
ROM ID INFORMATION TABLE:
Upgrade Event #507
Model

EM

TM

SYS

ECU P/No.

ROM ID
Previous

New

91952 Q5010
437
91952 Q5020
A00
ICU
SP2
ALL
ALL
91952 Q5370
A11
A33
91952 Q5380
A20
91952 Q5430
A31
To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM ROM
ID and reference the Information Table as necessary.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 4 of 8
SUBJECT:

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

 NOTICE
Prior to performing the ECU upgrade, be sure to check that the KDS is fully charged.
1.

Connect the VCI-II to the OBD-II
connector, located under the driver’s side
of the instrument panel.

 NOTICE
The ECU upgrade function on
KDS operates wirelessly. It is
not necessary to perform the
upgrade via USB cable.

2.

With the ignition ON, turn ON the KDS
tablet. Select KDS from the home
screen.

3.

Confirm communication with VCI (A) and
then configure the vehicle (B) using the
AUTO VIN (C) feature.

B
A

C
4.

Select ECU Upgrade.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 5 of 8
SUBJECT:

5.

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

The KDS will check the server for
recently uploaded Events and then
automatically download Upgrade Event
#507.

 NOTICE
The vehicle must be identified in
Vehicle Selection to download
an Event for that vehicle.

6.

KDS
screenshot
shown
above
is
for
demonstration purposes only. Events shown in
screenshot are not applicable to this bulletin.

Select Auto Mode.

CAUTION
Do NOT attempt to perform a
Manual Mode upgrade UNLESS
Auto Mode fails. Always follow
the instructions given on the
KDS in either Auto or Manual
mode.
7.

Select the ICU system under the System
selection menu.

D

Touch ID Check (D) and confirm that the
latest update is available.
Select Upgrade Event #507 and select
Upgrade to continue.

8.

The ECU upgrade will begin and the
progress of the upgrade will appear on
the bar graph. Upgrade part (1/2) (E) will
download the upgrade event to the VCIII. Upgrade part (2/2) (F) will upgrade the
ECU.

CAUTION

E

F

Do not touch the system
buttons (like ‘Back’, ‘Home’,
‘etc.’) while performing ECU
Upgrade.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 6 of 8
SUBJECT:

9.

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

If a “Communication Fail” screen
appears, verify that the VCI-II and KDS
are communicating properly. Touch OK
and restart the procedure from step 4.

 NOTICE
If an error notice continues to
appear or if the upgrade cannot
be
performed,
DO
NOT
disconnect
the
KDS/VCI-II.
Contact GIT America Help Desk
at (888) 542-4371 or Techline.
10. When instructed on the KDS, turn the
ignition OFF for ten (10) seconds then
back on. Touch OK to continue.

11. Once the upgrade is complete, touch OK
to finalize the procedure.

12. When prompted, select YES to check for
Diagnostic Trouble Codes (DTC) and
erase any DTCs stored such as EPS,
ESC, and TPMS that may have been set
during the upgrade.

13. Start the engine to confirm proper
operation of the vehicle.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 7 of 8
SUBJECT:

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

Manual Upgrade Procedure:

 NOTICE
The manual upgrade should ONLY be performed if the automatic upgrade fails.
If the automatic upgrade fails, turn the ignition OFF for about 10 seconds then place
it back in the ON position to reset the control unit BEFORE performing manual
upgrade.
See table below for Manual Mode passwords.

 NOTICE
It is recommended to ALWAYS check the Electronic Parts Catalog (EPC) to locate the
ECU Part Number respective to Auto/Manual Mode ROM IDs. DO NOT reference the
parts label affixed to the ECU.

Manual Mode ECU Upgrade Passwords
Menu

Password

SP2 ICU : 91952-Q5010/020/370/380/430

5430

1.

Within the ECU Upgrade screen displayed, select Manual Mode.

2.

Select the ICU system under the System selection menu. Select Upgrade Event #507
and select Upgrade to continue.

3.

Select the appropriate control unit part number with reference to the ROM ID Information
Table on page 3, and select OK.

4.

Enter the appropriate password from the Manual Mode password table above and select
OK.

5.

The upgrade will begin and the progress of the upgrade will appear on the bar graph.

6.

When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on.
Touch OK to continue.

7.

Once the upgrade is complete, touch OK to finalize the procedure.

8.

When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any
DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade.

9.

Start the engine to confirm proper operation of the vehicle.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020

Page 8 of 8
SUBJECT:

SERVICE ACTION: ICU OPERATION LOGIC IMPROVEMENT (SA435)

AFFECTED VEHICLE RANGE:
Model

Production Date Range

Seltos (SP2)

November 20, 2019 to August 13, 2020

WARRANTY INFORMATION:
N Code: N99 C Code: C99
Claim
Type

Causal P/N

Qty.

Repair
Description

Labor Op
Code

Op
Time

Replacement
P/N

Qty.

V

91952 Q5010

0

(SA435)
ICU Logic Improvement

200093R0

0.3
M/H

N/A

0

 NOTICE
VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers
should reference SA435 when accessing the WebDCS system.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SA435 Seltos (SP2) September 2020