NHTSA ID Number: 10167398
Manufacturer Communication Number: NTB19-076
TSB/Document Date: 2019-11-08
Summary
2018 ALTIMA AND ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: +?-+ - If DTCs other than those listed above are stored, this bulletin does not apply. +?-+ - If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. +?-+ - If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. +?-+ - If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
Confirm that all of the conditions
indicated in Figure 192 are being
met.
Required
conditions
185. Select Start.
Figure 192
93/102
NTB19-076
186. While maintaining all conditions shown
in Figure 192 and the Current status
indicates EXECUTING, shift the CVT
into R and then wait until the Current
status indicates COMPLETED.
HINT: This may take up to 3 minutes
to complete.
Figure 193
187. When the screen in Figure 194 is
displayed select End, shift the CVT
into P, and then turn the engine OFF.
Perform Select Learning
188. Start the engine, and then wait five (5)
seconds.
Figure 194
189. Move the shift selector to the N position and hold for more than two (2) seconds, and
then move it to the D position and wait for transmission engagement.
190. Repeat step 189 ten times.
191. Move the shift selector to the N position and hold for more than 2 seconds, and then
move it to the R position and wait for the transmission engagement.
192. Repeat step 191 ten times.
193. Move the shift selector to the P position, and then turn the ignition OFF.
Erase CVT Fluid Degradation Level Data
194. Select “Work Support” in “TRANSMISSION”.
195. Select “CONFORM CVTF DETERIORTN”.
196. Select “Clear”.
197. Clear any DTCs that may have set and then test drive the vehicle.
94/102
NTB19-076
PARTS INFORMATION
The following part kits are only to be used if the Sub-assembly is being replaced.
DESCRIPTION
PART #
QUANTITY
2018 Altima
31214-28X9E
BELT-PULLEY KIT
2018 Rogue AWD
31214-28X9B
1
2018 Rogue 2WD
31214-28X9C
CLAMP (Hose Spring Clamp)
16439-7S01E
2
I.
VALVE ASSY KIT-CONTROL (Valve body)
Valve Assy Kit-Control includes:
VALVE ASSEMBLY-CONTROL (1)
STRAINER ASSY-OIL, AUTO TRANS
BRACKET (Temperature sensor bracket)
BAND (Zip tie for bracket)
GSKT-OIL PAN
SEAL-LIP (Between CVT and control valve)
Seal, O-Ring (fluid filler plug gasket)
(1)
(2)
(3)
(4)
(5)
3170E-28X0B
1
1
1
1
1
1
1
1
SEAL-O RING (Transfer case to CVT AWD only)
33118-4BA0A
1
WASHER-DRAIN (For drain plug)
11026-JA00A
1
Loctite 5460 Sealant (2)
999MP-LT5460P
(3)
Nissan
NS-3 CVT Fluid (4) (5)
999MP-CV0NS3 As needed
Transmission Cooler Cleaner (5)
999MP-AM006P As needed
Lens Swab packet
J-51963
As needed
Includes QR label, CD-R, and control valve assembly.
Bill out Loctite 5460 Sealant under expense code 008. Do not include the Loctite
5460 Sealant part number on the claim.
One container of Loctite 5460 Sealant is good for approximately 5 repairs. This
sealant is not included in any kit.
For warranty repairs, Nissan NS-3 CVT Fluid must be used. For customer pay
repairs, Nissan NS-3 CVT Fluid, or an equivalent is recommended.
This item can be ordered through the Nissan Maintenance Advantage program:
Phone: 877-NIS-NMA1 (877-647-6621) or Website: Order via link on dealer portal
www.NNAnet.com and click on the “Maintenance Advantage” link.
J.
K.
L.
95/102
NTB19-076
If just a Control Valve is being replaced, use the following parts.
M.
N.
O.
DESCRIPTION
PART #
QUANTITY
CLAMP (Hose Spring Clamp)
16439-7S01E
2
VALVE ASSY KIT-CONTROL (Valve body)
3170E-28X0B
1
Valve Assy Kit-Control includes:
VALVE ASSEMBLY-CONTROL (1)
1
STRAINER ASSY-OIL, AUTO TRANS
1
BRACKET (Temperature sensor bracket)
1
BAND (Zip tie for bracket)
1
GSKT-OIL PAN
1
SEAL-LIP (Between CVT and control valve)
1
Seal, O-Ring (fluid filler plug gasket)
1
WASHER-DRAIN (For drain plug)
11026-JA00A
1
Nissan NS-3 CVT Fluid (2) (3)
999MP-CV0NS3 As needed
Transmission Cooler Cleaner (3)
999MP-AM006P As needed
Lens Swab packet
J-51963
As needed
(1) Includes QR label, CD-R, and control valve assembly.
(2) For warranty repairs, Nissan NS-3 CVT Fluid must be used. For customer pay repairs,
Nissan NS-3 CVT Fluid or an equivalent is recommended.
(3) This item can be ordered through the Nissan Maintenance Advantage program:
Phone: 877-NIS-NMA1 (877-647-6621) or Website: Order via link on dealer portal
www.NNAnet.com and click on the “Maintenance Advantage” link.
REMINDER! When instructed to reference the ESM for a repair procedure, ensure
one-time-use parts are replaced.
96/102
NTB19-076
CLAIMS INFORMATION
Q.
If Belt Inspection is not Performed and Sub-Assembly is replaced
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION
PFP OP CODE SYM DIAG FRT
JD01AA
CVT R&R
CVT SUBASSEMBLY
(WITH CONTROL VALVE R&I) RP
(1)
Reprogram TCM (when applicable)
(1)
(2)
(2)
JD023A
JX50AA
ZE
32
3.8
JE99AA
(2)
Reference the Parts Information Table and use the BELT-PULLEY KIT Part Number
31214-***** as the Primary Failed Part.
Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
HINT: FRT allows adequate time to access DTC codes. No other diagnostic procedures
subsequently required. Do NOT claim any diagnostic OP Codes with this claim.
EXPENSE CODE
EXPENSE CODE
008
DESCRIPTION
5460 Sealant
MAX AMOUNT
$12.46
CLAIMS INFORMATION continued on the next page.
97/102
NTB19-076
CLAIMS INFORMATION continued.
OR
If Belt Inspection is Performed and Sub-Assembly is replaced (belt inspection shows
signs of belt slip, NG)
Submit a Primary Part (PP) type line claim using the following claims coding:
MODEL
OPERATION
PFP OP CODE SYM DIAG
JD01AA
JD023A
All
CVT R&R
All
Inspect CVT Chain, Chain = NG
(Includes control valve R&I)
(1)
JX36AA
ZE
32
FRT
(2)
1.1
Altima
2.9
Replace CVT Sub-assembly
JX45AA
Rogue
3.0
All
Reprogram TCM (when applicable)
JE99AA
(2)
(1) Reference the Parts Information Table and use the applicable BELT-PULLEY KIT
Part Number 31214-***** as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.
EXPENSE CODE
EXPENSE CODE
008
DESCRIPTION
5460 Sealant
MAX AMOUNT
$12.46
OR
If Only Control Valve is replaced:
Submit a Primary Part (PP) type line claim using the following claims coding:
(1)
(2)
OPERATION
PFP OP CODE SYM DIAG FRT
Inspect CVT Chain, Chain = OK
JX37AA
0.3
Replace Control Valve
(1)
JD48AA
ZE
32
(2)
Reprogram TCM (When Applicable)
JE99AA
(2)
Reference the Parts Information Table and use the VALVE ASSY KIT-CONTROL part
number (31705-*****) as the Primary Failed Part.
Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
HINT: FRT allows adequate time to access DTC codes. No other diagnostic procedures
subsequently required. Do NOT claim any diagnostic OP Codes with this claim.
98/102
NTB19-076
Check off the parts as they are used in the Service Procedure and attach the
completed form to the repair order.
A.
PARTS KITS REFERENCE TABLE (Parts are listed in order of installation)
CHECK
DESCRIPTION
PART #
OFF
PUMP ASSY-OIL 31340-28X0A
PUMP ASSY-OIL
SEAL-O RING
31526-28X0C
Kit 31340-28X8A includes:
RING-SNAP
31506-1XF12
SEAL-O RING
31526-28X0A
(O-ring between CVT case and side cover)
PULLEY ASSY - CVT
31214-28X7A
(Belt and pulley “sub-assembly”)
Loctite 5460 Sealant
999MP-LT5460P
31377-1XD00
BOLT
(or 31377-1XZ0B)
SEAL-O RING
31526-28X0C
(For pulley retainer bolts)
SEAL-OIL,DIFF
38342-3VX0A
(Differential side oil seal; CVT case side)
BRG ASSY-THRUST NEEDLE (Thrust bearing)
See page 100
SEAL ASSY-OIL
31375-1XF00
(Torque converter oil seal; converter housing)
SEAL-OIL,DIFF (Differential side oil seal;
38342-3VX0B
converter housing side, front wheel drive only)
SEAL-O RING (For input shaft)
31526-80X01
Loctite 5460 Sealant
999MP-LT5460P
BOLT
31377-1XD00
FLTR ASSY-OIL,AUTO TRANS (CVT fluid filter)
31726-28X0A
SEAL-O RING (For filter cover)
31526-3VX0A
SEAL-LIP (Between CVT and control valve)
31528-1XZ0A
BRACKET (Temperature sensor bracket)
31069-3VX0D
VALVE ASSY-CONT (Control valve)
31705-28X0B
BAND (Zip tie for bracket)
24224-3VX0A
STRAINER ASSY-OIL, AUTO TRANS
31728-28X0A
GSKT-OIL PAN
31397-1XF0D
WASHER-DRAIN (For drain plug)
11026-JA00A
Seal O-Ring (Speed Sensor)
31526-1XG0C
Transmission Cooler Cleaner
999MP-AM006P
CLAMP (Hose Spring Clamp)
16439-7S01E
SEAL-O RING (CVT filler plug at converter housing) 31526-3VX0B
Nissan NS-3 CVT Fluid
999MP-CV0NS3
SEAL-O RING (Transfer case to CVT, AWD only)
33118-4BA0A
99/102
QUANTITY
1
1 (of 7)
1
1
1
As needed
19 (of 42)
6 (of 7)
1
1
1
1
1
As needed
23 (of 42)
1
1
1
1
1
1
1
1
1
1
As needed
2
1
As needed
1
NTB19-076
THRUST BEARINGS
B.
DESCRIPTION
PART #: 31407-
BEARING THICKNESS
QTY
THRUST BEARING
1XZ0B
1XZ0C
1XZ0D
1XZ0E
1XZ1A
1XZ1B
1XZ1C
1XZ1D
3.57
3.75
3.93
4.1
4.28
4.46
4.61
4.79
1 of each is
included in the
Pulley Kit. Select
1 for installation.
100/102
NTB19-076
R.
PART KITS VISUAL REFERENCE
The following Figures show the smaller components of KIT-PULLEY.
KIT- CONTROL VALVE is not shown.
31375 - 1XF00
Figure 195 shows
the assorted seals,
O-rings, etc. in
“KIT-PULLEY”
Figure 195
PUMP ASSY-OIL parts
BRG ASSY-THRUST NEEDLE parts
Figure 196
Figure 197
101/102
NTB19-076
REMINDER! Attach the following to the repair order:
Total EndPlay calculation (Page 63)
Parts Kit Reference Table (Page 99)
C-III plus screen showing the TCM part number before and after the reprogramming
(Step 152 on page 89)
C-III plus screen showing the current calibration data (Step 155 on page 90)
C-III plus screen showing the new calibration data (Step 171 on page 91)
AMENDMENT HISTORY
DATE
October 8, 2019
REFERENCE
NTB19-076
DESCRIPTION
Original bulletin published
102/102
NTB19-076
- 6X better wear protection on critical engine parts than...
- 1.3X better sludge protection than industry standards*
- 3X Stronger against viscosity breakdown than leading full...
- Protection for 10,000 miles between oil changes
- Meets or exceeds the following specifications: API SP/SN...
- Formulated for engines with 75,000 miles or more, Valvoline...
- Delivers 20% better wear protection and 15% better sludge...
- Extra detergents safeguard against friction, corrosion and...
- Advanced friction-fighting additives help maximize...
- Provides performance benefits for high mileage, new and...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: NTB19-076
Replacement Service Bulletin Number:
MFR Communication Date: 2019-10-08
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Obd2 Bluetooth Scanner Lifetime Update: Ediag Elite offers revolutionary Advantage Lifetime Updates with unlimited access to the superior 15 reset service, bidirectional testing and full system diagnostics.The Ediag Elite is an excellent Bluetooth obd2 scanner diagnostic tool ideal for diy's and private car owners
- Bidirectional Control for Quickly Locating Problems: The Bidirectional Scan tool allows you to send commands directly from your smartphone to your vehicle for active testing. This feature helps to quickly narrow down problems such as air conditioning clutches, windows, doors, sunroofs, etc., reducing diagnostic time for mechanics and helping Diy users locate faults more easily. In addition, Ediag Elite provides fault analysis and repair guidance to help you solve problems efficiently.
- 15 Maintenance Resets: The current version introduces 15 popular special features: Oil Reset, Headlight Matching, Bleeding Reset, TPMS Reset, BMS Reset, Gear Box Relearn, Throttle Learning, Injector Coding, SAS Reset and more special functions in system diagnose menu. These functions make it easy for owners to carry out the necessary maintenance and servicing, ensuring that your vehicle stays in top condition, prolonging its service life and preventing common problems and breakdowns. Note: The Special function vary by model& year, Reach us check compatibility.
- Wide Compatibility CANFD & FCA
Autoauth: Compatible with GM, Ford, Toyota, Chrysler, Honda, Mazda, Nissan, Mitsubishi, Hyundai, KIA with standard OBD2 port from 1996 to newer. More car brands and features will be released gradually. Newest Ediag Elite scanner supports CANFD Protocol and FCA cars. Note: Coverage may vary on different vehicle by model& year ,Please contact us to confirm compatibility before purchase. - Perfect for Monitoring The Health of Your Vehicle: Ediag Elite is designed to make vehicle maintenance simple and efficient. With intelligent AutoVIN quick recognition, it is easy to connect to your car without the need for manual input. Real-time data is visualized in a variety of formats, including graphs, numeric, meter displays and clear 4-in-1 data charts, allowing you to effortlessly monitor real-time data. Data logging/reporting is available for playback and further analysis.
- No Annual Fees & 2026 Upgraded CAN FD: Why pay $199/year or more for updates? The 2026 newest Kingbolen K7 obd2 scanner features have been upgraded to Lifetime Updates without subscription fees, saving you significant costs in the long run. K7 scan tool also adds the CAN FD protocol for the latest GM models (2019+), enabling faster data transfer, reducing the risk of undetected errors
- 2026 Newest Top-tier Car Scanner: Kingbolen K7 diagnostic scan tool is equipped with most capabilities for daily repair/maintenance: Wireless diagnosis via Bluetooth, Bidirectional Test, ECU Online/Offline Code, 31+ Resets, PMI for Ford, Lincoln, Mazda, Global version for 100+ brand vehicles and 17 languages, no area limit, FCA AutoAuth
- OE-Level Full Systems Scan Tool: K7 professional diagnostic scanner with Auto Vin can do one-click to scan ECUs on most of vehicles, like pcm, ecm, eps, bcm, tpms, sas, a/c system... to read/clear code, view live data, freeze frame, read ecu info. 4-in-1 data stream graphics can make data viewing more intuitive. Detailed diagnostic reports will help you easily master the car situation as it can be shared by bluetooth or email! Adding workshop information can help your customers to know more
- Bidirectional Test/Active Test & ECU Code: Stop guessing and start fixing. Bidirectional scan tool Kingbolen K7 can perform real active test that can send commands to the vehicle's ECU to drive the actuators to work, like window, rear mirrors, sunroof, door, solenoids, wipers, headlamp, etc, helping you quickly find out bad parts and pinpoint faulty issues. K7 bidirectional scanner will be a good choice to save money and time on car repairs when performing complex maintenance and repair
- 31 Reset Functions: Avoid expensive dealership visits for simple services. Experience tells us that just a small repair service may cost a lot of money. Kingbolen K7 is a professional diagnostic scanner with 31 common maintenance services like Oil /SAS/EPB/TPMS Reset, Battery Matching, ABS Bleeding, Injector Code, etc. It effectively handles most of the car reset and relearning jobs, perfect for experienced DIYers and mechanics. Note: Functions in the menu vary across vehicles. Kindly check the compatibility before purchase
- 【Lifetime Database & Software Updates— No Subscription Fee, No Feature Lock, Save you $399/Y】KINGBOLEN K8 Pro's software can already be permanently upgraded and used for while software of other same price product still needs annual fee of almost $400. K8 pro scanner has packed all capabilities auto technicians would ever need for repair & maintenance services: Added CAN-FD & DOIP protocol, Bluetooth Wireless Diagnosis, Bidirectional Test, ECU Online/Offline Code & Guided Functions for VW, for Audi...34+ Restes, Autoauth for FCA SGW, Larger 4GB+64GB memory, 12600mAh battery, 8'' touch screen with 1280 * 800 Resolution. A Kickstand can allow the tablet to sit at a comfortable angle
- 【Newly Added CAN FD & DOIP Protocol】As Upgrade Version of Kingbolen K8, K8 Pro obd2 scanner supports CANFD and DOIP protocol, which will save you 200+ bucks as no need extra buy for special adapter. CANFD protocol suits for the latest GM(2019-), reducing the risk of undetected errors. The DoIP protocol (comes with DoIp cable) fits for 2017+ BMW(F&G chassis), for Jaguar & Land Rover after 2017, for Volvo after 2018. Plus, K8 Pro's Memory from 2G+32G expanded to 4G+64G, update period extended from 2 years to permanent
- 【34+ Hot Special Functions & V.A.G Guide】KINGBOLEN K8 pro bluetooth obd2 scanner covers almost all common services including Oil Reset, EPB, SAS, BMS Reset, ABS bleed, Throttle Reset, Suspension, Injector Code, Power Balance, Transmission Adaptation, Fuel Trim Learn, HVAC Control Module Calibrate, Language Change, A/F Settings, Stop/Start Reset, Crankshaft Sensor Relearn, TPMS, PMI function and etc. Imagine how much money and time you spend on car maintenance every year? K8 pro car scanner will be a good helper and saver for your car. V.A.G Guided function provides step-by-step guide to work for Volkswagen/Audi/Skoda. Note: Please send us model/year/vin to check compatibility before order
- 【Powerful Bidirectional Test/Active Test & ECU Code】As a bidirectional scan tool, KINGBOLEN K8 pro allows you to request information from a vehicle's ECU or send commands to the vehicle's modules to perform specific tests and functions, such as EVAP Tests, Turn on/off radiator fan, Window/Mirror/Door Lock Test, Pump and Value Tests, Sound horn Test, et. Without using the vehicle control system and dismantling car’s parts, it can quickly and accurately pinpoint the fault causes, simple operation saves time and money
- 【Wireless OE-Level All Systems Diagnostics】Equipped with Bluetooth VCI, you can do car diagnostics out of the car (up to 33F/10M) without being confined to a small space inside the car. Provides the convenience of Auto VIN, K8 pro allowing for easy access and diagnosis of all available modules on a wide range of vehicles, like PCM, ECM, BCM, TPMS, SAS, Fuel System, etc, to perform read/clear codes, view live data, freeze frame, perform active tests, and read ECU info... 12-In-1 Data Stream Graphics make data viewing more intuitive.Diagnostic reports can be shared via QR Code, Bluetooth or email.Built-in Browser and Fault Code Library allows you directly query the fault code when diagnosing
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.