Classification:

Reference:

BT19-011

Date:

NTB19-079

October 11, 2019

REAR PILLAR MOLDING REPLACEMENT
APPLIED VEHICLES:

2016 - 2019 Maxima (A36)

SERVICE INFORMATION
If the rear pillar molding needs to be replaced for any reason, refer to the SERVICE
PROCEDURE starting on the next page.

Rear pillar
molding

Figure 1

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/7

SERVICE PROCEDURE
Mounting for the rear pillar molding on 2016 – 2019 Maxima now requires a 19/64th inch
(7.5 mm) mounting hole for the rear clip and urethane adhesive installed in 2 locations.
ALL rear pillar moldings on 2016 – 2019 Maxima must now be installed using this method.

Figure 2

1.

Measure the rear pillar moldings
rearmost clip mounting hole diameter.
HINT: Use a 19/64th inch (7.5 mm) drill
bit to check mounting hole diameter.


If a 19/64th inch (7.5 mm) drill bit
DOES fit, skip to step 9 on page 5.



If a 19/64th inch (7.5 mm) drill bit
DOES NOT fit, continue to step 2 on
the next page.
Figure 3

2/7

NTB19-079

2.

Apply tape to mask off the rearmost
clip mounting hole area.

Figure 4
3.

Apply masking tape to the 19/64th drill bit, leaving 1.57 inches (40 mm) exposed for
reference purposes.

Figure 5

4.

Figure 6

Drill a 19/64th inch (7.5 mm) hole no
more than 1.57 inches (40 mm) deep.

To avoid damage to the vehicle, do
not drill more than 1.57 inches (40mm)
deep, otherwise the drill bit will contact
internal body panels.

Figure 7

3/7

NTB19-079

5.

Clean all burrs and metal shavings from the drilled hole and surrounding area.

6.

Coat the bare metal using a zinc-rich
primer similar to RUST-OLEUM® Cold
Galvanizing Compound shown in
Figure 8.
a. Spray a small amount of zinc-rich
primer onto a cotton swab as shown
in Figure 9, below.
b. Apply zinc-rich primer to the bare
metal of the drilled hole as shown in
Figure 10, below.
Figure 8

Figure 9

Figure 10

7.

Allow sufficient time for the primer to dry. (Refer to the instructions supplied with the
primer to ensure sufficient drying time.)

8.

After the primer has dried, apply touch-up paint. (Refer to the instructions supplied
with the touch-up paint to ensure sufficient drying time.)

4/7

NTB19-079

9.

Remove any existing urethane from the areas shown in Figure 11 and Figure 12,
below.
To prevent rust from forming, apply touch up paint if the paint is scratched while
removing the urethane.

Figure 12

Figure 11
10.

Apply Betaseal™ 43533 glass primer
onto the newly cleaned rear pillar
finisher areas shown in Figure 14,
below.

Betaseal™ 43533
glass primer

HINT:
Allow the Betaseal™ 43533 glass
primer to dry for AT LEAST 20
seconds or the urethane will NOT
adhere to the rear pillar finisher.
Figure 13

30 mm
15 mm

15 mm
30 mm
Figure 14
5/7

NTB19-079

11.

Apply Betaseal™ 57302N urethane in a circular motion starting from the outside to
the inside of the rear pillar finisher, as indicated by the arrows in Figure 15 and
Figure 16, below.


Apply the urethane to a height of 8 mm and a width of 10 mm.
Finish here
(inside)

Start here
(outside)

Figure 15

Finish here
Finish here
(center)
(inside)
Start
here
(outside)
Start
here
(outside)

Figure 16
12.

Align the rear pillar finisher with the clip mounting holes in the vehicle.

13.

Push the rear pillar finisher IN toward the vehicle body until the clips are fully seated.

14.

Inspect fitment and ensure rear pillar finisher and surrounding area is clean.

15.

Allow 24 hours for the Betaseal™ 57302N urethane to cure.
6/7

NTB19-079

PARTS INFORMATION
DESCRIPTION

PART NUMBER

QUANTITY

Rear pillar molding, left

78873 – 9DJ0A

1

Rear pillar molding, right

78872 – 9DJ0A

1

Betaseal™ 57302N urethane (1)

999MP - 57302NP

(As needed)

Betaseal™ 43533 glass primer (2)
999MP - 43533PP
(As needed)
RUST-OLEUM Cold Galvanizing
7785830
(As needed)
Compound (3)
(1) The DOW® automotive chemical Betaseal™ 57302N urethane adhesive is
recommended. Equivalent products may be used.
(2) The DOW® automotive chemical Betaseal™ 43533 glass primer is recommended.
Equivalent products may be used.
(3) The RUST-OLEUM Cold Galvanizing Compound is recommended. Equivalent products
may be used.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Repair Rear Pillar Molding
(1)
BX6VAA
(2)
(2)
0.3
(1) Reference the electronic parts catalog and use the appropriate Rear Fender
Molding as the Primary Failed Part (PFP).
(2) Use Appropriate Symptom and Diagnosis Code for concern.
EXPENSE CODE
067

DESCRIPTION
Sealant/Primer

MAX AMOUNT
$4.95

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
October 11, 2019

NTB19-079

DESCRIPTION
Original bulletin published

7/7

NTB19-079