Installation and Conversion Instructions

911 (992)
7/19

ENU

6807

6

Door Entry Guard, Illuminated ADY/ATX

Concern:

Retrofitting

Model Year:

As of 2019

Note:

The illuminated door entry guards made of carbon-fiber composite (ADY) or stainless steel (ATX) are
installed in the door sill areas.

Figure 1
Parts Info:

992.044.820.XX1

1

 Carbon/stainless-steel door entry guard with "model designation", set

For details of available model designations and carbon-fiber composite or stainless steel versions,
see Porsche Electronic Parts Catalog (PET).

Tequipment

Aug 5, 2019
Page 1 of 5

6

911 (992)
6807

ENU

Installation and Conversion Instructions

7/19

Parts List:

Figure 2

Materials:

Tools:

———

2x

Wire harness

———

——

Cleaning agent (commercially available)

———

——

Wrapping tape/insulating tape

WE1119 - Hot-air blower, Leister-Electron/VAG 1416, VAS1978/14A or equivalent

Work
Procedure:

Aug 5, 2019
Page 2 of 5

Information
•

Some of the repair illustrations show only one side of the vehicle or a similar component.

•

Naturally, some steps also have to be performed on the opposite side of the vehicle as well.

1

Preparatory work
1.1

Disconnect and connect battery charger.  Workshop Manual '2X00IN Battery trickle
charging'

1.2

Remove and install inner strips.  Workshop Manual '2X00IN Removing and installing inner
door sill trim'.

1.3

Remove and install cover for fuse box.  Workshop Manual '2X00IN Removing and installing
front side-section trim panel'.

1.4

Remove and install door entry guards.  Workshop Manual '2X00IN Removing and installing
cover strip'.

Tequipment

Installation and Conversion Instructions

911 (992)
7/19

ENU

6807

6

Information
Ensure socket contact is seated securely.
2

Route and plug in wire harness on driver's side
2.1

Fold over carpet on driver's side in the fuse box area.

2.2

Fit ground line - brown cable - of the wiring
harness on the ground pin  Figure 3 -1- in
the driver's footwell at the left. Tightening
torque: 6.5 ftlb. (9 Nm). Secure ground
line to the wiring harness  Figure 3 -2- with
adhesive tape/wrapping tape.

Figure 3
2.3

Plug power supply line - red cable - at the
black connector housing connection point
for the door wire harness on the connector
side coming from the vehicle into  Figure 4
-1-pin 16. Release connector and guide pin
into the connector housing until it locks with
an audible click. Lock the connector again
and connect it. Route cable on the wiring
harness  Figure 4 -2- down to the vehicle
floor and secure it to the wiring harness using
suitable adhesive tape/wrapping tape. Do
not use tie-wraps!

2.4

Route cables on the wiring harness as far
as the door entry guard using adhesive
tape/wrapping tape.

Figure 4

Tequipment

Aug 5, 2019
Page 3 of 5

6

911 (992)
6807

ENU

2.5

7/19

Installation and Conversion Instructions

Fit illuminated door entry guard (see Step
1.4). Remove door seal close to the cable
routing and route cable over the body flange
 Figure 5 -1-. Fit door seal and connect
connector for illuminated door entry guard to
the connector on the wiring harness.
2
3

– Cable for illuminated door entry
guard
– Door entry guard

Information
Ensure socket contact is seated securely.
3

Figure 5

Route and plug in wire harness on passenger's side
3.1

Fold over carpet on passenger's side in the fuse box area.

3.2

Fit ground line - brown cable - of the wiring
harness on the ground pin  Figure 6
-1- in the passenger footwell at the right.
Tightening torque: 6.5 ftlb. (9 Nm).
Secure ground line to the wiring harness 
Figure 6 -2- with adhesive tape/wrapping
tape.

Figure 6

Aug 5, 2019
Page 4 of 5

Tequipment

Installation and Conversion Instructions
3.3

Plug power supply line - red cable - at the
red connector housing connection point
for the door wire harness on the connector
side coming from the vehicle into  Figure 7
-1-pin 16. Release connector and guide pin
into the connector housing until it locks with
an audible click. Lock the connector again
and connect it. Route cable on the wiring
harness  Figure 7 -2- down to the vehicle
floor and secure it to the wiring harness using
suitable adhesive tape/wrapping tape. Do
not use tie-wraps!

3.4

Route cables on the wiring harness as far
as the door entry guard using adhesive
tape/wrapping tape.

911 (992)
7/19

ENU

6807

6

Figure 7
3.5

Fit illuminated door entry guard (see Step
1.4). Remove door seal close to the cable
routing and route cable over the body flange
 Figure 8 -1-. Fit door seal and connect
connector for illuminated door entry guard to
the connector on the wiring harness.
2
3

4

Concluding work
4.1

Working Time:

– Cable for illuminated door entry
guard
– Door entry guard

Figure 8

Complete steps 1.1 to 1.4 in reverse order.

68073200: Installing illuminated door entry guard
Includes:
Installing electric wire harness, removing and installing cover
strips.

Labor time: 145 TU

Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.

© 2019 Porsche Cars North America, Inc.

Tequipment

Aug 5, 2019
Page 5 of 5