T-SB-0013-16 February 26, 2016 CP) TOYOTA

Technical Service Bulletin

Techstream Smart Key Programming

Service
Category Vehicle interior
Toyota Supports

Section Theft Deterrent/Keyless Entry Market USA ASE Certification
Applicability :

YEAR(S) MODEL(S) ADDITIONAL INFORMATION

2016 Yaris SD MEX-Prod
Introduction

The Yaris SD is equipped with Smart Start and Remote Keyless Entry. This bulletin details the
Techstream key programming process. Please follow the key programming procedures outlined
in this bulletin for the following:

e Smart ECU Replacement

e Engine ECU (PCM) Replacement

e Key erase procedure

e Adding a Key

e All Keys are jost, how to turn the IG-ON

NOTE
This bulletin is for Puerto Rico ONLY.

Warranty Information

OP CODE DESCRIPTION TIME OFP 71 T2
N/A Not Applicable to Warranty _ _ a —
Required Tools & Equipment
REQUIRED EQUIPMENT SUPPLIER PART NUMBER aTy
Techstream 2.0* TS2UNIT
Techstrearn Lite ADE TSLITEPDLRO1 1
Techstream Lite (Green Cable) TSLP2DLRO1
* Essential SST.
NOTE
* Only ONE of the Techstream units listed above is required.
* Software version 11.00.017 or later is required.
e Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.

© 2016 Toyota Motor Sales, USA Page 1 of 33

CPTOYOTA _ T-SB-0013-16 February 26, 2016

Techstream Smart Key Programming

Page 2 of 33

Repair Procedure

NOTICE

¢ The engine cannot be started if any step or procedure for each service operation is
skipped. Perform all procedures in order.

* Ifany metallic or magnetic object is near the key, communication between the key and
vehicle may be obstructed, resulting in a failure to program the immobilizer system.

« Remove all devices that can send/receive radio waves from the vehicle; including cell
phones and laptops (Techstream included).

* Do not start the engine unless instructed to do so during the process. If the engine is
started during immobilizer system programming, the programming mode is canceled.

e Keep ail keys away from the vehicle during programming unless otherwise instructed.

NOTE

e 2 (two) or more keys must be programed for the engine to start.
* A maximum of 6 (six) keys can be programmed to 1 vehicle.

* The number of programed keys can be verified by Techstream.
« Techstream MUST be connected to the network for each process outlined in this bulletin.

TECHSTREAM UTILITY

WHEN TO USE PROCEDURE
Forced IG-ON e All keys are lost, and JG has to be ON to enter Smart A
Key Utility (See Page 3)
Smart Parameter |* Needed if you replace the Smart ECU B
Reset * Needed if you replace the PCM (See Page 7)
If one or all keys are lost, or they are stolen, use this utility
Smart Key Erase | to erase all the codes and register new keys. C
and Registration (See Page 15)
Once you do this, any key not present will no longer work
and will have to be programmed.
Register Additional | e Needed if you want to add one key. D
Smart Key e Need to have at least one key to do this utility (See Page 25)
NOTE

e Please refer to T-SB-0043-14 “Immobilizer and Smart Key Reset” for the security
authorization process.

e Procedures B, C, and D require a Seed Number and Passcode.

© 2016 Toyota Motor Sales, USA
GPTOYOTA _ T-SB-0013-16 February 26, 2016 Page 3 of 33

Techstream Smart Key Programming

Procedure A — Forced IG-ON

1. Connect Techstream to the vehicle.

Figure 1.

< Select >

AL eergecan ties OC herpaane tes UF 22234 claws vt 22 8 Delete

2. Choose Toyota, Yaris, 2016, P5 and press Next.
Figure 2.

© 2016 Toyota Motor Sales, USA
CPTOYOTA _ T-SB-0013-16 February 26, 2016

Techstream Smart Key Programming

Page 4 of 33

Procedure A ~ Forced IG-ON (Continued)

3. Select Smart Key from the System Selection Menu.

Figure 3.

fh Techtrenee a 18S = TMT
Fit Furchen Setip 1% Une Help
Sywem Select | Stored Data |

System Selection Menu
Sedect Geared system mned her perae Pe sete button la icpens the EL)
| Voto * ECU talus unbattan
[Semen | Waite © ECU communcaton OK
on | Aytem | Vinee widstensk © ECU net kupparted 3 nel rerpondng
Seiten | Lgid Blue eiAstensh = ECU commuretanon OK m past tara bat nol rmugandeg eee,

ANECUs | Powter | Chases | Body Eecical |

4. From the Utility Selection Menu, select Utility from the Left Menu and then select Forced

Ignition ON.
Figure 4.

Fin Fantom Sewn TS Ue Help
Syutem Setect | Sota Smart Key Live |

ie LA
PS

T

| UUllty Selection Mem

| Select desired Uthey and-then press Haxt button
[Carden = a
On-Demand SebTest

| [Cuntoraze

Sletroductian»
Than fanchen i used 19 tum a kgrbeor (10) OH (Engine OF Fteady OFF) ethout mreqestered smart ney

oS Be ae Tarver moras

© 2016 Toyota Motor Sales, USA
CPTOYOTA _ T-SB-0013-16 February 26, 2016 Page 5 of 33

Techstream Smart Key Programming

Procedure A — Forced IG-ON (Continued)
5. The Forced Ignition ON Utility will begin. Figure 5.

fr ;
[ torcea Enitien CN SU-O1-O0L

ee coer a ss se
1

Please follow the prompts on the screens. 7 |
| This function is used te turn the ignition (IG} ON
(Engine OF FiReady OFF) without a registered

| smartkey

Confirm the following condrions.

- IG is OFF

- No registered smart keys are in the vehicle.

- All doors and engine hood are closed

- The vehicle is not in smart key registration mode.

Press "Next" to activate the forced ignition ON

j | Next > | Exit |
}

6. Press the engine/power switch once and Figure 6.
press Next within 60 seconds. Forced ignttion ON (SSU-02-00) Be. =o

Press engine/power switch only once and press
"Next" within 60 seconds

Time Remaining: 57 sec

io

< Back | Next> | Exit |
ry

© 2016 Toyota Motor Sales, USA
GPTOYOTA _ T-SB-0013-16 February 26, 2016 Page 6 of 33

Techstream Smart Key Programming

Procedure A — Forced IG-ON (Continued)

7. Press the engine/power switch to turn the IG Figure 7.
ON (Engine Off/Ready OFF). Once the Forced fgnitian ON (SSU-01-003)
ignition is turned on, press Next to proceed.

“Help

| Press engine/power switch to tum IG ON (Engine
| OFF/Ready OFF),

After IG is turned ON, press "Next' to proceed

| ow | m |

Figure 8.

8. Forced Ignition ON is complete. Once Foced ton ON 50-01-08

pressing Exit, you will be returned to the Ser. rane ‘ol
Utility Selection Menu.

| Forced Ignition ON is complete.

Proceed to Procedure C.

© 2016 Toyota Motor Sales, USA
GPTOYOTA _ T-SB-0013-16 February 26, 2016 Page 7 of 33

Techstream Smart Key Programming

Procedure B — Smart Parameter Reset

1. Select Smart Key Function.

Figure 9.
seem RE TTT]

fae Functon tetup FH User Help
Sywer Select | Stared Data Smact ey Live |

Utility Selection Manu
Select desired Liulty and thert prvas Next button

Configuration
On-Demand Self-Test
Customize

anes
| Thee fechon csgtays the Smart Kay function

2. Select Smart Parameter Reset. Figure 10,
“Smart Key Function (SSU-08-008)

=

1
|
| Select a function according to the repair manual.

Press "Next" to proceed.

© Smart Parameter Reset |