Ignition status

Timer

Progress display

Figure 31

25/40

NTB15-037e

55. When OK is displayed, select Next.

Step
55

Figure 32
56. Operate the shift selector per the on-screen instructions.
a. Move the shift selector to P; then move P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.
57. Select Next.

Step
57

Step
56

Figure 33

26/40

NTB15-037e

58. Erase all DTCs as follows:
a. Turn the ignition OFF.
b. Turn the Ignition ON.
c. Wait for DTC erase to complete.

59. Select Next.

Turn ignition ON > OFF > ON
ON

Step
59

Figure 34

27/40

NTB15-037e

60. Verify the before and after part numbers are different.
61. Print a copy of this screen (Figure 35) and attach it to the repair order.
62. Select Confirm.

Step
60

Step
61

Step
62

Figure 35

NOTE: If you cannot print the above screen:
a. Select Screen Capture.
b. Name the file.
c. Save the file in My Documents.


A copy of the screen is now saved in the CONSULT PC. It can be retrieved and
printed at a later time.

28/40

NTB15-037e

ERASE MEMORY DATA
NOTE: This procedure is for all Applied Vehicles.

63. Navigate C-III plus to the screen shown in Figure 36.


Diagnosis (All Systems) > TRANSMISSION > Work support

64. Select ERASE MEMORY DATA.

65. Select Start.

Step
64

Step
65

Figure 36

29/40

NTB15-037e

66. Follow the on-screen
instructions; maintain
the following conditions:
a. Parking brake set.
b. Ignition ON, with the
engine OFF.

Step
67

c. Fully depress the
accelerator.
d. Put shift selector in
R.
67. Select Start.
Figure 37

68. When the Current status
changes to
COMPLETED, select
End.

Step
68

Figure 38

69. Move the shift selector to P, and then turn the ignition OFF.
70. Turn the ignition ON, and then confirm P and N display by moving the shift selector in
those positions.

30/40

NTB15-037e

CONFORM CVTF DETERIORTN
NOTE: This procedure is for all Applied Vehicles.
71. Navigate C-III plus to the screen shown in Figure 39.


Diagnosis (All Systems) > TRANSMISSION > Work support

72. Select CONFORM CVTF DETERIORTN.
73. Select Start.

Step
72

Step
73

Figure 39
74. Select Start.

Step
74

Figure 40
31/40

NTB15-037e

75. Select Clear.

Step
75

Figure 41

76. Select Yes.

Step
76

Figure 42

32/40

NTB15-037e

77. When CVFT DETERIORATION DATE changes to “0”, select End.

0

Step
77

Figure 43

78. Start the engine.

79. Set the parking brake.

80. Turn OFF the A/C.

81. Bring the engine to normal operating temperature range.

82. Confirm the CVT fluid temperature is over 122°F (50°C).

33/40

NTB15-037e

Auxiliary gearbox clutch point learning
NOTE: This procedure is for all Applied Vehicles.

83. Navigate C-III plus to the screen shown in Figure 44.


Diagnosis (All Systems) > TRANSMISSION > Work support

84. Select Auxiliary gearbox clutch point learning.
Or


If this feature is not available in the vehicle that is being repaired, skip to Manual
Auxiliary gearbox clutch point learning on page 38.

85. Select Start.

Step
85
Step
84

Figure 44

34/40

NTB15-037e

86. Follow the on-screen instructions in Figure 45, and then select Start.

Step
86

Figure 45
87. With the brake pedal still applied, shift the CVT selector lever into the D position.


Figure 46 (below) will be displayed after shifting into D position.

NOTE: The Current status will show EXECUTING (Figure 46), but until the vehicle is
shifted into the D position, Auxiliary gearbox clutch point learning will not begin.

Step
87

Figure 46

35/40

NTB15-037e

88. Continue to depress the brake pedal until the Current status shows “Completed” as
shown in Figure 48 at the bottom of this page.
NOTE: This may take several minutes to complete.

Figure 47
89. When Completed is displayed, select End.

Step
89

Figure 48

90. Shift the vehicle into “P”, turn ignition OFF and release the brake pedal.
91. Perform Auxiliary Gearbox Clutch Point Learning (steps 83 to 89) one additional time
(a total of two times).

36/40

NTB15-037e

Erase DTCs
NOTE: This procedure is for all Applied Vehicles.
92. Use C-III plus to erase any transmission DTCs that may have stored.
93. Turn OFF C-III plus.
94. Disconnect C-III plus and the plus VI from the vehicle.
95. Verify the CVT operates normally and no abnormal noises are heard during a test drive.

37/40

NTB15-037e

MANUAL AUXILIARY GEARBOX CLUTCH POINT LEARNING
CAUTION: If clutch touch point learning is not performed, you may feel shift shock
when the auxiliary transmission shifts.
NOTE: This manual procedure is only needed if the auto procedure is not available in
C-III plus.
a. Start the engine and warm up the CVT fluid to 50°C (122°F).
NOTE: Confirm the CVT fluid temperature by “FLUID TEMP” in “Data Monitor”.
b. Turn the air conditioner OFF.
c. Shift the CVT selector lever to the P position, turn the ignition OFF and then wait for
5 seconds.
d. Start the engine and allow it to idle for 5 seconds.
e. Turn the ignition OFF and then wait for 30 seconds.
f. Perform Step “e” to Step “f” two more times (Total: Three times).
g. Start the engine.
h. Allow engine to idle for 30 seconds.
i. Shift the CVT selector lever to D position.
j. Accelerate the vehicle from 0 km/h (0 MPH) to 65 km/h (40 MPH) at low throttle
(0.5/8 – 1/8).
k. Decelerate the vehicle to 30 km/h (18 MPH) or less without using brakes.
l. Stop the vehicle and shift the selector lever to P position.
m. Turn the ignition OFF and wait for 5 seconds or more.
n. Restart the engine.
o. Perform Step “j” to Step “o” four times (Total: Five times).
p. Shift the selector lever to D position.
q. Accelerate the vehicle from 0 km/h (0 MPH) to 45 km/h (28 MPH) at low throttle
(0.5/8 – 1/8).
r. Stop the vehicle and shift the selector lever to P position.
s. Turn the ignition OFF for 5 seconds or more and then restart the engine.
t. Perform Steps “q” to Step “t” four times (Total: Five times).
u. Drive the vehicle and check that no shock occurs while shifting gears.

38/40

NTB15-037e

PARTS INFORMATION
All Vehicles
DESCRIPTION
PART #
QUANTITY
GASKET (CVT drain plug)
11026-JA00A
1
NS-3 CVT Fluid
999MP-NS300P (1)
as needed
(All vehicles listed below except
2012 MY Versa Sedan)
NS-2 CVT Fluid (2012 MY Versa Sedan only)
999MP-NS200P (1)
as needed
(1) NS-2 and NS-3 CVT Fluids can be ordered through the Nissan Maintenance Advantage
program: Phone: 877-NIS-NMA1 (877-647-6621). Website order via link on dealer
portal www.NNAnet.com and click on the “Maintenance Advantage” link.

Versa Sedan MY 2013-2017 and Versa NOTE MY 2014-2017
DESCRIPTION
PART #
KIT-CONTROL VALVE

QUANTITY

3170E-X428B

1

----

1
1
1

PART #
31705-3JX8A
31728-3JX0B
31397-3JX0A

QUANTITY
1
1
1

PART #

QUANTITY

3170E-X428C

1

----

1
1
1

Kit Includes
VALVE ASSY - CONTROL
GASKET - OIL PAN
STRAINER ASSY-OIL
Versa Sedan MY 2012
DESCRIPTION
VALVE ASSY - CONTROL
STRAINER ASSY-OIL
GASKET - OIL PAN
Sentra MY 2013-2017
DESCRIPTION
KIT-CONTROL VALVE
Kit Includes
VALVE ASSY - CONTROL
GASKET - OIL PAN
STRAINER ASSY-OIL

39/40

NTB15-037e

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION

PFP

OP CODE

SYM

DIAG

FRT

Replace Control Valve

(1)

JD48AA

HC

32

(2)

(1) Refer to the Electronic Parts Catalog (FAST) and use the applicable Control Valve
Assembly Part Number (31705-*****) as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.

And if needed on the same line
OPERATION
OP CODE
FRT
Reprogram TCM
JE99AA
(1)
(1) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.

40/40

NTB15-037e