Instruction Sheet

IS-17900A

WHEEL FENDER STAINLESS STEEL PROTECTOR
H SERIES VEHICLES – B-1721- Today
REVISION:A
2017-04-07

This revision replaces all previous versions
Changed vehicle effectivity. Was 2004.

MATERIAL
Kit #7770321 includes the following parts:
Part No.

Description

Qty

470933

FENDER PROTECTOR

8

506869

TAPE RUB ADH2 POL .031" x 1/4" x 300' / BLACK

1

684517

ADHESIVE SIMSON #ISR 70-03 / GREY / 310ml CARTRIDGE

1

504643

RIVET POP DOME OE 1/8x.640 SS

40

5001067

WASHER FL .128x.312x.032 SS

40

IS-17900

Instruction Sheet

1

FI-17900

Feuille d'instructions

1

NOTE
Material can be obtained through regular channels.
Other parts that may be required:
Part No.
682986

Description
STANDOX Anti-Silicone cleaning fluid, 4 liter

Qty
1

PROCEDURE

DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition
switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter
type vehicles, set the battery master switch (master cut-out) to the OFF position.

Writer: FL

IS-17900A
Page 2 / 5

GLUING – BEST PRACTICES
Health & Safety
DISCARD

WEAR

WEAR

WASTE PROPERLY

GLOVES

SAFETY GLASSES

Work environment
- Free from excessive dust (ensure ventilation).
- Air jet prohibited. (Propels dust into the working environment and causes surface contamination from the
oil of the pneumatic system).
- All products containing silicone are prohibited.
o
Temperature and % humidity: The standard is established at 23 C (73°F) and 50% relative humidity.
Effect of temperature;
o
> 23 C and/or > 50%, drying time and working time are reduced
o
< 23 C and/or < 50%, drying time and working time are increased
On the other hand, usage of products, parts, surface preparation and/or bonding is not allowed below
o
15 C.
General information for cleaning / surface preparation products

Do not
rub back and forth

Writer: FL

Check the expiry date

Do not pour
directly from the bottle

IS-17900A
Page 3 / 5

NOTE
The kit includes the required material to install 8 stainless steel fender protectors on a vehicle.

FIGURE 1 PROTECTOR LOCATIONS

1. Water-clean the fender’s lower
edge. Clean the inner and outer
faces thoroughly, removing any
dirt, salt, sand or road material.
Dry the surface.
2. Next, clean the protector,
removing any dust or residue.
3. Once dry, use anti-silicone to
prepare
the
fender
and
protector surfaces for bonding.

FIGURE 2 :CLEAN THESE AREAS ON FENDER

Writer: FL

IS-17900A
Page 4 / 5

4. Select a glue applicator nozzle
that creates 8mm high glue
beads. (Figure 3)
5. If unavailable, cut an 8mm high
triangular opening in the tip.
(Figure 3)

FIGURE 3 TRIANGULAR BEAD OF GLUE

6. Perform a dry fit of the protector
on the fender. Mark tape
positions with masking tape
according to Figure 4.
7. Prepare two 14-1/4” lengths of
double-face tape.
8. Immediately position the tapes
on the fender.
9. Apply a bead of Simson glue
between the tapes Figure 4.

FIGURE 4 : TAPE PLACEMENT UNDER PROTECTOR.

Writer: FL

IS-17900A
Page 5 / 5

10. Within 10 minutes of glue
application, place protector
against inner face of fender
(1, Figure 5 ). Then, push
against outer face (2, Figure 5 ).

FIGURE 5 INSTALLATION SEQUENECE

11. Using the protector as a
template, drill 1/8” holes for
rivets. (5x)
12. Install the rivets.

FIGURE 6

13. Full curing time: 9 1/2h @ 73°F (23°C), 50% Relative Humidity.
Curing time may be shorter or longer depending on temperature and humidity.

PARTS / WASTE DISPOSAL
Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)

Writer: FL