2017

Pre-Delivery Inspection
Technician Reference Document

Effective 8-18-2016-US
Version 1.7

Table
of Contents
A3/S3/A3
TDI
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.

Table of Contents
3-4

A4 Sedan

5-6

A5 Sport/S5 Cabriolet

7-8

A5 Sport/S5 Coupe

9-10

A6/A6 competition/S6

11-12

A7/A7 competition/S7/RS 7/RS 7 performance

13-14

A8 L/S8 plus

15-16

Q3

17-18

Q5/SQ5

19-21

Q7

22-23

R8 Coupe

24-25

TT/TTS Coupe

26-27

TT Roadster

Effective 8-18-2016-US
Version 1.7

Model Year 2017 | Audi Pre-Delivery Reference Document | 2

A4 Sedan
Technician Reference Document
Vehicle Preparation

Trunk Inspection

•      Deactivate vehicle transport mode

•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit

This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Deactivate vehicle transport mode (via Special functions >
PDI service > 19-Transport mode activating/deactivating.)
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)*
Using ODIS, right click the 5F-Information control unit 1,
and select “Guided Functions > 5F-Adaptations > Storage of
music activating/deactivating (option 2) and when prompted
for the Optical drive, choose option 1 for “On”
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2017 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
•      Check operation of windows and locks
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Verify and set language and Measurement Units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech dialog system is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to Medium

Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)

Effective 8-18-2016-US
Version 1.7

Via “Menu->Vehicle->Left Option->Driver Assistance->Parking
Aid”
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials > Turn ignition on > Insert the
Onboard DVD into the DVD Drive > Select Menu > Vehicle >
Left Option > Vehicle Settings > Owner’s manual and with
the CD/DVD inserted select “Yes” to start the update > Turn
off ignition to start update (the update will take approx. 5
minutes) > Once completed, remove the disk and place back
into the case for the next vehicle
Model Year 2017 | Audi Pre-Delivery Reference Document | 3

A4 Sedan
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

•      Set dealership location in navigation (if equipped)

•      Install wheel bolt covers and center caps as supplied

Set dealership location for following back to dealership
during road test
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
•      Verify Audi connect Information Packet is present (if
equipped)
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, AT&T Terms & Conditions
(T&C) (if applicable)
•      Verify system connects to mobile network (if equipped).
Review TSB 2042942 for additional information
Make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
•      Turn on the wireless network (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi options > Wi-Fi Mode “Hotspot”)
•      Check Wi-Fi hotspot functionality (if equipped)
Check Wi-Fi hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI__XXXX,” where XXXX
is the last four digits of VIN. via Telephone > Options > Wi-Fi
options > Wi-Fi Mode “Hotspot” > Hotspot settings > Access
point (SSID)
•      Enable Google Earth (if equipped)
Enable Google Earth in the Navigation > Map Settings and
verify the white Google logo appears in the bottom right
hand corner of the MMI screen

Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2017 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)

On-Hoist Inspection
•      Perform a coolant reservoir cap pressure test
via ELSA -> Enter VIN # -> Repair manual Engine -> 4-Cylinder
Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III)
-> 19 Cooling System -> Coolant System/Coolant -> Cooling
System, Checking for Leaks -> Pressure Relief Valve in Cap,
Checking. Only the procedure “Pressure Relief Valve in Cap,
Checking” should be performed in the document Cooling
System, Checking for Leaks
•      Inspect wheel bolts for proper torque
Use torque wrench to verify

Effective 8-18-2016-US
Version 1.7

Model Year 2017 | Audi Pre-Delivery Reference Document | 4

A5 Sport/S5 Cabriolet
Technician Reference Document
Vehicle Preparation

Trunk Inspection

•      Deactivate vehicle transport mode

•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2017 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation

Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature

Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation

Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify speech dialog system is operating
Press the “Talk” button and verify several commands

Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers

Effective 8-18-2016-US
Version 1.7

•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle

Model Year 2017 | Audi Pre-Delivery Reference Document | 5

A5 Sport/S5 Cabriolet
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

•      Set “Music volume while parking” to 6 lines

•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle

Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
•      Verify Audi connect Information Packet is present (if
equipped)
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Turn on the wireless network (if equipped)
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)

If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2017 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Convertible Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)

•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit

Effective 8-18-2016-US
Version 1.7

Model Year 2017 | Audi Pre-Delivery Reference Document | 6

A5 Sport/S5 Coupe
Technician Reference Document
Vehicle Preparation

Trunk Inspection

•      Deactivate vehicle transport mode

•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2017 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation

Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature

Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify speech dialog system is operating
Press the “Talk” button and verify several commands

Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers

Effective 8-18-2016-US
Version 1.7

•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle

Model Year 2017 | Audi Pre-Delivery Reference Document | 7

A5 Sport/S5 Coupe
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

•      Set “Music volume while parking” to 6 lines

•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle

Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
•      Verify Audi connect Information Packet is present (if
equipped)
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
•      Connect the dealer demo SIM card to verify system
connects to mobile network