start
→ "BIU Initializing
communication..." display

(Additional registration mode)
→ "KEY is being collated."

→ "Collation complete"

3

4

Trouble mode

31

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1411 is stored.)

Immobilizer antenna failure
Transponder failure

NG Antenna

NG Key - Communication Failure

Prepare the registered key.

•NG key
•Unregistered key
Body integrated unit failure
With collation status OK, the key was not replaced (left for 60
seconds)
Immobilizer antenna failure
Transponder failure
Body integrated unit failure

NG Use of Unregistered Key

NG IMM Control Module EEPROM

NG Performed conditions not
established.

NG Antenna

NG Key - Communication Failure

NG IMM Control Module EEPROM

Perform the diagnosis for DTC B1577 (P1577).

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1411 is stored.)

—

Perform the diagnosis for DTC B1577 (P1577).

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

Transponder failure and body integrated unit failure

NG Key-Immob comm/ Immob unit
EEPROM

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

DTC is detected except for a new unit of TYPE B-1. Therefore, check
DTC and perform the diagnosis.
[When body integrated unit is TYPE B-1 and unregistered]
Inspect the communication line between meter/security CM and body
integrated unit. (Diagnosis for DTC B1409)
When the same error is indicated again even after the inspection and
retrying the procedure, replace the combination meter/security CM.
[Cases other than above]
Read out DTC and perform the diagnosis. (Collation NG: B1401 or
B1405) (Communication NG: B1407 or B1409) (EEPROM abnormal:
B1408 or B1406)

Execute "Meter/SCU registration" to register the combination meter/
security CM.

—

[Body integrated unit unregistered]
•Communication failure between combination meter/security CM and
body integrated unit
•Combination meter/security CM malfunction
Meters / SCU can not register for the
[Body integrated unit registered]
quasi normalization.
•Collation unmatched between combination meter/security CM and
body integrated unit
•Communication failure with combination meter/security CM
•Combination meter/security CM malfunction

Combination meter/security CM unregistered

Number of registrations exceeded

NG Number of registrations
exceeded

Check version of Subaru Select Monitor.
Replace the body integrated unit.

Key IN, IGN-ON not completed [Only when the error screen on the left Wait approximately one minute, perform key IN, IGN-ON, and retry the
is indicated after five seconds or more elapsed]
procedure.

Body integrated unit erroneous operation (possibility that last
registration mode still not canceled)

Wait approximately one minute, and retry the procedure.
When the same error is indicated again, remove the Subaru Select
Monitor once. Wait approximately one minute, and retry the
procedure.
When the same error is indicated again, remove and install the
battery.

CAN communication failure between Subaru Select Monitor and body
Perform the diagnosis for LAN system.
integrated unit (Only when K line communication is used for ECM)

•Subaru Select Monitor failure
•Body integrated unit failure

Meter/SCU not registration

Action to be taken

CAN communication failure between Subaru Select Monitor and body
Perform the diagnosis for LAN system.
integrated unit

NG BIU security access NG

NG BIU-SSM Communication

Select "Immobilizer" from the Main NG Comm. Failed
Menu
→ System "Immobilizer" → Smart
System "NO" → IGN-ON "YES" → Command input screen

2

1

No.

Note:
TYPE B-1: Model other than TYPE B-2
TYPE B-2: From 2015MY LEGACY / OUTBACK

A list of possible trouble mode, when an error screen is displayed at each status (procedure).

5-8 Correspondence table when registration is not possible

S1001BE.fm

B type
REGISTRATION MANUAL FOR IMMOBILIZER

Vehicle-id:
SIE-id::
Å`

２０１４年４月３０日

→ "Collation complete"

(Body integrated unit replacement
mode)
→ "Confirm you replace all the
keys..."

6

7

→ "Key has been registered"

Status (procedure)

32 ページ

5

No.

S1001BE.fm

32
Body integrated unit failure

NG IMM Control Module EEPROM

Immobilizer antenna failure

NG Antenna

Transponder failure

With collation status OK, the key was not replaced

NG Key - Communication Failure

NG key (at least one key)

NG Performed conditions not
established.

Immobilizer antenna failure

NG Antenna

NG Use of Unregistered Key

Time-out before the key is replaced (60 seconds)

NG Performed conditions not
established.

Transponder failure

Communication failure with combination meter/security CM

NG Meter/SCU Communication

NG Key - Communication Failure

Combination meter/security CM malfunction

NG Meter/SCU error

Body integrated unit failure

NG IMM Control Module EEPROM
With four keys registered, IGN-OFF → ON

Transponder failure

NG Key Communication Failure

Trouble mode

NG Performed conditions not
established.

Immobilizer antenna failure

Screen

午後２時９分

NG Antenna

水曜日

Action to be taken

Perform the diagnosis for DTC B1577 (P1577).

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1410 is stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
as follows:
1) Retry the procedure using a different key.
2) Replace the immobilizer antenna, and retry the procedure.
3) Replace the body integrated unit.

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1411 is stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
for DTC B1411.

—

Prepare the registered key.

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1410 is stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
as follows:
1) Retry the procedure using a different key.
2) Replace the immobilizer antenna, and retry the procedure.
3) Replace the body integrated unit.

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1411 is stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
for DTC B1411.

—

Check DTC and perform the diagnosis.
(When this screen is displayed, B1407/B1409 is stored.)

Check DTC and perform the diagnosis.
(When this screen is displayed, B1408/B1406 is stored.)

—

Perform the diagnosis for DTC B1577 (P1577).

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1411 is stored.)

B type
REGISTRATION MANUAL FOR IMMOBILIZER

Vehicle-id:
SIE-id::
Å`

9

8

No.

S1001BE.fm

２０１４年４月３０日

→ "EGI initialization / During
registration..."

→ "Key has been registered"

Status (procedure)

33 ページ

Action to be taken

33
Subaru Select Monitor failure

ECM failure

NG EGI-SSM Communication

ECM failure

NG EGI unit EEPROM

NG EGI security access NG

Perform the diagnosis for DTC B1577 (P1577).

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
battery.
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)

Check version of Subaru Select Monitor.
Replace the ECM.

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
battery.

Perform the diagnosis for DTC B1572 (P1572).

Body integrated unit failure

NG IMM Control Module EEPROM

Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1407/B1409 is
stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
as follows:
1) Inspect the communication line between combination meter/
security CM and body integrated unit.
2) When the same error is indicated again even after the inspection
and retrying the procedure, replace the combination meter/security
CM.

DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1408/B1406 is
stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
as follows:
1) Clear the memory, and retry the procedure.
2) When the same error is indicated again even after retrying the
procedure, replace the combination meter/security CM.

—

Perform the diagnosis for DTC B1577 (P1577).

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1411 is stored.)

NG EGI-Immobilizer communication Communication failure between ECM and body integrated unit

Communication failure with ECM

Combination meter/security CM malfunction

NG Meter/SCU error

NG EGI-SSM Communication
(Communication line judgment)

With four keys registered, IGN-OFF → ON

NG Performed conditions not
established.

Communication failure with combination meter/security CM

Body integrated unit failure

NG IMM Control Module EEPROM

NG Meter/SCU Communication

Transponder failure

NG Key - Communication Failure

Trouble mode
Immobilizer antenna failure

Screen

午後２時９分

NG Antenna

水曜日

B type
REGISTRATION MANUAL FOR IMMOBILIZER

Vehicle-id:
SIE-id::
Å`

11

10

No.

S1001BE.fm

２０１４年４月３０日

→ "EGI initialization / During
registration..."

"Engine ECU registration" start
→ "BIU Initializing
communication..." display

Status (procedure)

34 ページ

Screen

午後２時９分

Action to be taken

Perform the diagnosis for DTC B1577 (P1577).
Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1408/B1406 or B1407/B1409 is
stored.)

Body integrated unit failure
•Communication failure with combination meter/security CM
•Combination meter/security CM malfunction
Combination meter/security CM not genuine part
Combination meter/security CM unregistered
Communication failure with ECM

NG IMM Control Module EEPROM

NG Meter/SCU error

NG Meters / SCU checking NG

NG Performed conditions not
established.

NG EGI-SSM Communication
(Communication line judgment)

34
Subaru Select Monitor failure

ECM failure

NG EGI-SSM Communication

ECM failure

NG EGI unit EEPROM

NG EGI security access NG

Perform the diagnosis for DTC B1577 (P1577).

Body integrated unit failure

NG IMM Control Module EEPROM

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
battery.
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)

Check version of Subaru Select Monitor.
Replace the ECM.

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
battery.

Perform the diagnosis for DTC B1572 (P1572).

NG EGI-Immobilizer communication Communication failure between ECM and body integrated unit

Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)

Execute "Meter/SCU registration" to register the combination meter/
security CM.

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1401/B1405 is stored.)

Prepare the registered key.
Execute "Immobilizer system registration" to register the key to the
body integrated unit.

•NG key
•Unregistered key
•Body integrated unit unregistered

NG Use of Unregistered Key

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)
Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1410 is stored.)

Transponder failure

NG Key - Communication Failure

Check DTC and perform the diagnosis.
(When this screen is displayed, DTC B1411 is stored.)

Transponder failure and body integrated unit failure