®TOYOTA
T-SB-0146-13

Technical Service Bulletin

September 27, 2013

Short Pin lnsta llation Du ring PDS
Service
Category
Section

General

Toyota Supports ~

Pre-Delivery Service

Market

ASE Certification*

USA

Applicability
YEAR(S)

MODEL(S)

2014

Avalon , Avalon HV

ADDITIONAL INFORMATION

Introduction

To minimize battery discharge during transportation and storage , the Short Pin has been remcwed
at the assembly plant and tempora rily stored in the engine compartment Relay Block . Rei nstall
the Short Pin into its original locati on and confirm all related Diagnostic Trouble Codes (DTCs)
are cleared during Pre-Delivery Service (PDS).
NOTE
The Short Pin is removed only on vehicles going to Hawaii, Puerto Rico, Saipan, Guam , and
American Samoa.

Required Tools & Equipment
REQUIRED EQUIPMENT

Tech stream 2 .O*
TIS Techstream

QlY

PART NUMBER

SUPPLIER

TS2UNIT

ADE

TSPKG1

Techstream Lite

TSLITED LR0 1

• Essential SST.

NOTE
• Only ONE of the Techstream units listed above is required.
• Software version 8.20.019 or later is required.
• Additional Tech stream units may be ordered by calling Approved Dealer Equipment (ADE) at
1-800-368-6787.

Warranty Information
OP CODE

DESCRIPTION

N/A

Not Applicable to Warranty

© 2013 Toyota Motor Sales , USA

TIME

OFP

T1

T2

Page 1 of 3

@TOYOTA

September 27, 2013

T-SB-0146-13

Page 2 of 3

Short Pin Installation During PDS

Installation Procedure
Remcwe the Short Pin from the blank space of the Relay Block in the engine compartment and
install the Short Pin in the Relay Block as shown.
Figure 1.

3

j Remove this Short Pin

NOTE
·• The Short Pin does NOT function as a·fuse, so install it only in the position shown.
• If the vehicle is stored after PDS, disconnect the negative(-) battery terminal to prevent
battery discharge. Refer to Service Bulletin No. PG001-06, "Battery Maintenance for In-Stock
Vehicles and Pre-Delivery."

OTC Clearing Procedure
With the Short Pin removed, several different ECUs may detectthe interruption in battery voltage
(B+) and store a OTC. Clear any DTCs after installing the Short Pin.
1. Connect Techstream to DLC3.
2. Cycle the ignition switch to the "IG-ON" position.

© 2013 Toyota Motor Sales, USA

®TOYOTA

T-SB-0146-13

September 27, 2013

Page 3 of 3

Short Pin Installation During PDS

OTC Clearing Procedure (Continued)

3. Using Techstream , check to see if any DTCs other than those listed in the table below are stored .
OTC NUMBER

MEANING OF OTC

U0155

Lost Communication with "Combination Meter''

U0199 (with Memory Seat)

Lost Communication with "Door Control Module A"

U0200 (with Memory Seat)

Lost Communication with "Door Control Module B"

U0208 (with Memory Seat)

Lost Communication with "Seat Control Module A"

NOTE
If any DTCs besides those listed in the table remain, repair the applicable system according to
the Repair Manual.
4. Erase DTCs .

© 2013 Toyota Motor Sales , USA

®TOYOTA Avalon /Avalon HV
2014 PRE-DELIVERY SERVICE CHECK SHEET
BEFORE INSPECTION

~ 111
~.

01 Install Short Pin* (Hawaii, Puert o Rico , Saipan , Guam ,
American Samoa) ................................... ............. ............

D

UNDER VEHICLE (ON HOIST)
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ........ ............................................................ ..
02 Inspect tires for defects/damage .... .. ..... ...... .... ... ......... .. ...
03 Initialize lire Pressure Warning System (TPWS) (see
page 2) ....... ...... ........ ............. ... .. ......... .... ... .................... .
04 Install wheel covers/caps/spare ti re wheel covers* ...... .. .
05 Check hybrid transmission flu id level* .... ... ... ....... ...... .
06 Inspect for fuel , oil, coolant, and other fluid leaks .......... .
07 Inspect under the vehicle for damage , rust, etc ............. ..
08 Visually check bolts and nuts on chassis and powertrain
for looseness ..... ............................ ........................ ..........
09 Install rubber body plugs (stored in glove box or center
console)' ........ ....... .. .......... ....... .. ........................... ..... .... .
10 Install front wheel opening extension pads (see page 2)

FUNCTIONALOPERAT~N
,Appypa~ng

brake and cyde igni5oo "K3-0N'; place gearselecbrin reverre, tum on bghts
and rear debg;ier. Unlock aUdoors, release tuei door, release trunk /JafdJ.

01
02
03
04
05
06
07
08
09
10
11

Check dome , courtesy, map , and sun visor lights' ..........
Chec k warning/i ndicator lights , gauges , and horn ... .. ......
Check windshield wi pers and washers ........................ ....
Chec k headlights, instrument lights, turn signals ,
emergency flashers , and brake lights ..............................
Check inside/outside rear view mirror operationiadjustment
Check cigarette lighter* and power outlets ....... .. .............
Check audio/navigati on' /backup camera• systems and
set clock ............ .............. ............ .. ... ...... ...... .. .. .. ..... .. ......
Verify EntunefNavigation software version (Display
Audio, Non-HOD Type only)* ............ .... ... .................
Install shift-lock override button cover .............. ...... ........
Check slidi ng roof' ..................... .......... ............... ...........
Check rear sunshade operati on• .............. .......................

DD
DD
DD
DD
DD
DD
DD
DD
D
DD
DD

ROAD TEST

Enter Odometer Readings
Reading Before Test _ _ _ _ _ Reading After Test: _ _ _ _ _ _

01
02
03
04
05
06

Start at left front door. Check wndowand door lock operauon (from master pov.er
slllitch, if equipped). Continue around vehicle in a counterc/odwiise direcuon
checking each door and wndowoperation, child door locks, seat bells, interior
condiuon, all l1ghts. lufJIJBe co~rtment contents. Finish by checking headlight
aim and conunue into
ER H
D checks.

CJD
DD
CJD
DD
DD
DD
DD
DCJ
DD
DCJ
CJD

07

OB
09
10
11
12
13
14

01 Remove interior protective covers, unnecessary labels.
tags , etc . (Remove just before deli very to customer) ..... ..
02 Vi sually inspect all interi or parts for installati on ,
damage, fit, dirt, etc . .. .................... ....... ....... .......... .. .... ... .
03 Verify floor mat application and install using
retaining clips* .................................. .............. ............. ..
04 Veri fy green light is illumi nated on SOS (Safety
Connect) button• ............ ..... ................... ..... .....................
05 Remove Rapgard TM and clear protecti ve bumper fi lm• ....
06 Wash and clean vehicle ... ................ ....... ......... ...... ....... .. .
07 Inspect paint finish for scratches , chips , rust, dents ,
damage , etc ........... .................... ........ ............... ...... .. ...... .
08 Inspect exterior body parts for proper installati on ,
damage , rust, etc . ..... .......... ............ ... ..... ......... ............. ..
09 Place oil change sti cker on inside of wi ndshield, top
left corner ....... ........... ...... ..... ... ........ .. ............... ...... .. .. .. ...
10 Place Owner's Guide and fi rst aid ki t portfolio'
in glove box .......... .... ........... .. ......... .... ...... ....... .......... .. ...