Technical Service Bulletin

$-SB-0016-13 May 8, 2013 ep Scion?)
Floor Mat Installation During PDS
Service
Category General

Scion Supports ae
Section Pre-Delivery Service Market USA ASE Certification pga
Applicability

YEAR(S) MODEL(S) ADDITIONAL INFORMATION

2014 FR-S, iQ, tC, xB, xD

Introduction

2014 model year vehicles are equipped with driver’s side floor mat retaining clips to secure the floor
mat in the correct position. In addition, some models may utilize retaining clips for passenger side
floor mats as well. Follow the appropriate installation procedure to attach the driver's side and
passenger's side (if applicable) floor mat to the vehicle carpet using the floor mat retaining clips
during Pre-Delivery Service (PDS).

CAUTION

* ALWAYS verify the floor mat to ensure it is designed specifically for the model and model
year it is being installed in.

ONLY use floor mats that can be retained using the retaining clips. All OEM Scion floor mats
are specifically designed to fit correctly and be retained using the retaining clips.

Make sure the floor mat is properly placed on the vehicle carpet and secured with the retaining
clips. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere
with the movement of the pedals during driving and may cause an accident.

Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance
to the mat.

NEVER install more than one floor mat at a time in the driver’s seating position.

If applicable, any secondary set of floor mats (based upon customer preference, such as the

_all weather floor mats or other floor mats} MUST be placed in the trunk with all the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.

Warranty Information

OP CODE DESCRIPTION TIME OFP Ti | T2
N/A Not Appticable to Warranty - - - _

© 2013 Toyota Motor Sales, USA Page 1 of 12

oSsciom S-SB-0016-13 May 8, 2013 Page 2 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style

1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.

2. Attach the driver and passenger side (if applicable) floor mats to the vehicle carpet using the
retaining clips. Secure the mat by inserting the retaining clips through the grommet holes.
Figure 1.

1 Retaining Clips 3 | Correct Installation

2 Grommets

© 2013 Toyota Motor Sales, USA

oSscian S-SB-0016-13 May 8, 2013 Page 3 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style (Continued)

3. Verify proper installation.

NOTE

If applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.

Figure 2.

© 2013 Toyota Motor Sales, USA

Ssciormn S-SB-0016-13 May 8, 2013 Page 4 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip

1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.

2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.

f
\

1 Retention Clip 5 | Cross-sectional Diagram

2 | Front of Vehicle A | Retention Clip Claw

3 j Retention Clip Eyelet on Vehicle Floor B | Locking Clip

4 } Seat

© 2013 Toyota Motor Sales, USA

wscion S-SB-0016-13 May 8, 2013 Page 5 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip (Continued)

3. To lock the retention clip in place, insert the Figure 4.
locking clip of the retention clip into the designated
hole.

| 1 | Locking Clip

4. Align the floor mat holes with the retention clip Figure 5.
hooks and place the floor mat holes onto the

retention clip hooks. (1)
ae (
—_ ye
Cl
- .

Om

1 Retention Clip Eyelet on Floor Mat

2 Retention Clip

3 Front

© 2013 Toyota Motor Sales, USA

Ssciom $-SB-0016-13 May 8, 2013 Page 6 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip (Continued)

5. Verify proper installation.

NOTE

lf applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.

Figure 6.