Technical Service Bulletin

Rev1

S-SB-0017-12

(D !::i C::: I CJ r l

August 17, 2012

2013 Scion xD Pre-Delivery Service
Service
Category

General

Section

Pre-Delivery Service

Market

USA

Scion Supports ~
ASE Certification~

Applicability
YEAR(S)

MODEL(S)

2013

xD

ADDITIONAL INFORMATION

REVISION NOTICE
June 20, 2013 Rev1:
• The Functional Operation, Walkaround Inspection, Under Hood, Road Test, and Final
Inspection & Cleaning sections have been updated.
Any previous printed versions of this bulletin should be discarded.

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback
indicates the following areas deserve special attention when performing PDS:
• Careful inspection for paint chips/scratches and body dents/dings.
•

Proper operation of electrical accessories (including interior light, clock, and radio reset).

•

Interior cleanliness.

•

Proper function of mechanical systems.

Customer retention and proper maintenance of vehicles has been a major focus for Toyota. To help
remind customers that regular oil changes are essential to the proper maintenance of their vehicle,
dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing
this, customers will be reminded to return to your dealership for their first oil change. Your current
oil change reminder sticker may be used. (See PDS Check Sheet item 8 of "Final Inspection &
Cleaning".)
A new PDS Check Sheet has been developed for the 2013 model year Scion xD. Some check points
have been added, expanded or clarified. Bulletins are available for items in bold type.

© 2013 Toyota Motor Sales, USA

Page 1 of 6

S-SB-0017-12

Rev1

August 17, 2012

Page 2 of 6

2013 Scion xD Pre-Delivery Service

Warranty Policy

If the need for additional repairs or adjustment is noted during the Pre-Delivery Service, the requi red
service should be performed under warranty. Reimbursement will be managed under the warranty
policy.

The Warranty Policy and Procedures Manual requires that you maintain the completed PDS
check sheet in the customer's file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject to debit.
An additional Repair Order completed in conjunction with normal PDS must have time punch/flags
for ~ervice. If multiple repa irs are performed , separate time flags must be punched for each repair.
Reimbursement Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

1.0

N/A

N/A

N/A

Required Tools & Equipment

I

REQUIRED EQUIPMENT

I

Techstream 2.0*

I

TIS Techstream

SUPPLIER

PART NUMBER

QTY

TS2UNIT
ADE

Techstream Lite

TSPKG1
TSLITEDLR01

* Essential SST.

NOTE
• Only ONE of the Techstream units listed above is required.
• Software version 8.10.021 or later is required.
• Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at
1-800-368-6787.

Before Inspection

When performing new car Pre-Delivery Service, install DOME fuse before moving vehicle from
storage lot so that FUNCTIONAL OPERATION checks can begin as soon as vehicle is moved
intd the service stall.

1. Install DOME fuse - see check sheet
2. Install radio antenna

© 201 3 Toyota Motor Sales, USA

1

S-SB-0017-12

Rev1

August 17, 2012

Page 3 of 6

2013 Scion xD Pre-Delivery Service

Functional Operation

Apply parking brake and cycle ignition "IG-ON," place gear selector in reverse, turn on lights and rear
defogger. Unlock all doors, release fuel door, release rear hatch.
1. Check dome, courtesy, map, and sun visor lights*
2. Check warning/indicator lights, gauges, and horn
3. Check windshield wipers and washers
4. Check headlights, instrument lights, turn signals, dimmer switch, emergency flashers, and
brake lights
5. Check inside/outside rear view mirror operation/adjustment
6. Check cigarette lighter* and power outlet
7. Check audio/navigation* system, set SSP to xD*, and set clock
8. Install shift-lock override button cover
9. Check that the electroluminescent dash illuminates when the door is opened* (Scion Series
1Q_vehicles only)
10. Check that the shift knob illuminates* (Scion Series 10 vehicles only)
Walkaround Inspection

Starting at the left front door, check window and door lock operation and the operation of all power
windows and door locks from master switch. While walking around vehicle in a counterclockwise
direction, open left rear door and check operation of window regulator and door lock, set child safety
door locks to the normal (unlocked) position. Assure tightness of interior garnishes and check seat
belts. Inspect rear hatch contents and lights at rear of vehicle. Repeat checks at right rear door.
Inspect right front door window regulator and lock operation and garnishes. Check seat and seat belt
operation. Continue on around to the front of the vehicle checking lights.
1. Check door and door lock operation, including each wireless remote control/theft deterrent
system*
2. Check power window operation
3. Check that engine starts with all keys
4. Check that child safety door locks are in normal (unlocked) position
5. Check seats and seat belt operation
6. Check rear defogger
7. Check side marker, tail, backup, and license plate lights
8. Check rear hatch trim appearance

© 2013 Toyota Motor Sales, USA

!::iC::ICJ r1

S-SB-0017-12

Rev1

August 17, 2012

Page 4 of 6

2013 Scior xD Pre-Delivery Service

Walkaround In• pection (Continued)

9. Adjust spare tire pressure, inspect for damage, and check jack and tool installation
NOTE

Compact spare .tire -

60 psi (420 kPa).

10. Check headlight aim
Refer to the Repair Manual for procedures.
11. Check that front and rear exterior Scion badges illuminate after unlocking vehicle* (Scion Series
10 vehicles only)
Under Hood

1. Check engine oil and ATM* fluid levels
2. Check brake and clutch* fluid levels.
Visually inspect using see-through reservoirs.
3. Check engine coolant level
4. Check windshield washer fluid level

5. Check battery state-of-charge using Digital Battery System Analyzer
Refer to Service Bulletin No. PG001-06, "Battery Maintenance for In-Stock Vehicles &
Pre-Delivery."
NOTE

Battery SOC should be a minimum of 75%. Please enter the SOC Reading on the space
provided on the check sheet and attach the printout to the check sheet.

6 Inspect for fuel, oil, coolant, and other fluid leaks
Under Vehicle (On Hoist)

1 Remove disc brake anti-rust converslanti-corrosion wheel film* - PD017-04
Visually inspect rotors for rust.
NOTE

For best rotor rust prevention, retain wheel film on vehicle until just prior to customer delivery.

2 Inspect tires for defects/damage

3 Activate and Initialize Tire Pressure Warning System (TPWS) - see check sheet
© 2013 Toyota Motor Sales, USA

Rev1

S-SB-0017-12

August 17, 2012

Page 5 of 6

2013 Scion xD Pre-Delivery Service

Under Vehicle (On Hoist) (Continued)

4. Install wheel covers/caps/spare tire wheel covers*
5. Install rubber body plugs (stored in glove box)
6. Inspect for fuel, oil, coolant, and other fluid leaks
7. Visually check bolts and nuts on chassis and powertrain for looseness
8. Inspect under the vehicle for damage, rust, etc.
Road Test

A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road
surfaces and driving conditions. Check for unusual noise and driving performance.
1. Check cold engine operation
Check starting and fast idle operation performance.
2. Check engine operation during warm-up
Check that engine operates smoothly during warm-up.
Check for unusual noise, engine vibration, rough idle, etc.
3. Check engine at normal operating temperature
Check engine performance over a broad range of driving conditions, including idle quality,
acceleration, cruise and deceleration.
4. Check clutch or automatic transmission operation
Check manual transmission operation, including shift lever/linkage and unusual noise.
Check automatic transmission operation, including operation in each range, neutral start switch
·
and shift lock system.
5. Check brake and parking brake operation
Check brake function, including unusual noise, parking brake performance and all related brake
system indicator lights.
6. Check steering operation and off-center/vehicle pull/flutter
Check steering function.
Check steering off-center/vehicle pull/flutter.
7. Inspect for abnormal noise and vibration
8. Inspect for squeaks and rattles

© 2013 Toyota Motor Sales, USA

S-SB-0017-12

!:::iC:::I

2013 Scio

Rev1

August 17, 2012

Page 6 of 6

xD Pre-Delivery Service

Road Test (Co tinued)

9. Check front and rear* heater and A/C* operation

10. Check speedometer operation
11. Check cruise control operation*
Final lnspectio & Cleaning

1. Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers
just before delivery to the customer.)
Remove plastic covers from door panels, seats, head restraints, and sun visors, as required.
Remove labels, tags, and stickers (except those containing owner information).
NOTE

Consumer information labels, such as airbag information warning and bumper information
labels, MUST be left on the vehicle until delivery to a retail customer.

2. Verify floor mat application and install using retaining clips* - S-SB-0008-11
3. Visually inspect all interior parts for installation, damage, fit, dirt, etc.
4. Remove Rapgard™ and clear protective bumper film*
Ensure ALL glue residue is removed.
5. Wash and clean vehicle
6. Inspect paint finish for scratches, chips, rust, dents, damage, etc.
7. Inspect exterior body parts for proper installation, damage, rust, etc.
8. Place oil change sticker on inside of windshield, top left corner
Complete the mileage or date recommendation and apply the oil change reminder sticker to the
inside of the windshield, top left corner. You may use your current pil change reminder sticker.
9. Place Owner's Guide and first aid kit portfolio* in glove box

10. Perform Techstream Health Check
Perform Health Check to ensure that diagnostic trouble codes are not present. Health Check
results can be printed for the customer at delivery, or for the dealer file, using the Diagnostic
Report function.

11. Install front license plate - see check sheet
*Ins, ect or install when equipped or required

© 2013 Toyota Motor Sales, USA

@

FR-S
2013 PRE-DELIVERY SERVICE CHECK SHEET
=:iC:lc:Jrl

BEFORE INSPECTION

~ I~;
:a'~

UNDER VEHICLE (ON HOIST)

D

01 Remove disc brake anti-rust covers/anti-corrosion

0

01 Install DCC Fuse (see page 2) ······ ······ ······ ···· ·········· .... ..
02 Connect Delivery Mode Wire Harness Connectors
(see page 2) ... . ... ....... ... .. ... ...... . ..... ........