GROUP

HyunaRI I

nEWTHlnKlnG.
nEW POSSIBILITIES.

Technical Service Bulletin
SUBJECT:

CAMPAIGN
DATE
MARCH 2013

NUMBER
13-01-017
MODEL
ELANTRA (MD)

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

Gi>~®HYun~R,

ECU Update

Description: This bulletin provides a procedure to update the ECM and TCM software for 2013
Elantra (MD) vehicles with the latest update to revise the shift feeling in ECO mode .

This TSB supersedes TSB 12-01-046 to include retail vehicles.

*IMPORTANT

*** Dealer Stock and Retail Vehicles ***
Dealers must perform this Campaign on all affected vehicles prior to customer retail delivery and
whenever an affected vehicle is in the shop for any maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Veh icle Information" screen via WEBDCS to identify open Campaigns.

Applicable Vehicles: 2013 MY Elantra (MD) vehicles with automatic transmission (KMHDH ***)
Applicable Production Date Range: From March 14, 2012 through August 21 , 2012
GOS Information:
EVENT#

DESCRIPTION

288
290

288.13MY MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT-ECM
290.13MY MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT-TCM

NOTE: Submit claim on Campaign Claim Entry Screen

Circulate To: Service Manager, Warranty Manager, Service Advisors , Technicians, Fleet Repair

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

ECM ROM ID INFORMATION TABLE
ECM ROM ID
Model

Emission

ECM P/N

IMMO

39101-2EMN3

YES

39103-2EMN3

NO

39101-2EMP3

YES

39103-2EMP3

NO

SU LEV
ELANTRA

(MD)
1.8L
ULEV

Previous
MD3SP1MS2D2A
M D3SP1 MS2D2B
MD3SP1 NS2D2A
MD3SP1 NS2D2B
MD3UP1 MS2D2A
MD3UP1 MS2D2B
MD3UP1 NS2D2A
MD3UP1 NS2D2B

New
MD3SP1 MS2D8A
MD3SP1 NS2D8A
MD3UP1 MS2D8A
MD3UP1 NS2D8A

TCM ROM ID TABLE: Verify the TCM ROM ID before updating vehicle software.
TCM ROM ID
Model

ELANTRA
(MD)
1.8L

TSB #: 13-01-017

Engine

TCM P/N

1.8L

39101-2EMN3
39103-2EMN3
39101-2EMP3
39103-2EMP3

Previous

New

TMDOC18NA8

TMDOC18NA9

Page 2 of 7

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

GENERAL PRECAUTIONS
•
•

Connect the USB cable between the GOS and
the VCI.
Connect the 16-pin DLC connector from the VCI
into the DLC located under the driver's side dash.

*NOTE
Make sure the battery icon at the bottom right of the GOS laptop shows at
least 50%; if not, charge the GOS or attach a battery charger.
•

Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories (including
heater/air conditioner/fan, audio, heated seats, rear defroster, etc) to ensure the battery will not
be discharged during the update.

•

Perform the update with the ignition key in the ON position. (Turn the ignition key to the ON
position or press the Start-Stop Button two times without depressing the brake pedal).

•

Do not disconnect any cables connected to the vehicle or the GOS during the update .

•

Do not start the engine or turn the ignition switch OFF during the update.

*NOTE
~

Confirm your GOS has the most recent version. If not, connect the GOS to an
Internet port, open the GOS home page and select "Update". Refer to
instructions on hmaservice.com if necessary.
If you encounter GOS related problems, call the GIT Helpline at 888-437-0308.

TSB #: 13-01-017

Page 3 of 7

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

ECM UPDATE
GOS AUTO MODE ECM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN .
2 . Select Engine as the system and then select OK.
3. Select Auto Mode and then select Next.
4.

From the System tab , select Engine and then select OK. The GOS w ill read the ROM ID .
Confirm the ROM ID is applicable as shown on Page 2, "ECM ROM ID Information ".
NOTE : Record the ROM ID in case the auto update fails and a manual update is needed .

5. Update event 288.13MY UD/MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT - ECM
will display. Select Upgrade.

(

•Mode
Auto Mode

• Syst em

~

Y

Event Group

,. Curre nt ROM ID
~

Event List

.C'

)

TSB

'

~~~~===============~
IMD3UP1NS2D28

Latest ROM ID

IMD3UP1NS2D8A

288 13MY UDIMD 1 8 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT

ENGINE

D Event selecti o n
1. Review and understand related TSB f o r vehicle reprogramming.
2. Select reprogramming event from Upgrade Event pull down menu above .
3. Click t he Upgrade butto n to begin ECU upgrade.

ID Register

Option Treatment
Data Treatment
Inspection I Test

..:J

ECU Mapping Verification 1

s!,IJlll

=

caseAna.lysis

OTC

Cw-rent Data

Actuation

Test

Flight Record

OVOM

.~
Oscllloscope

I

~
Simulation
Test

6. If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the
vehicle battery by running the engine for 10 minutes.
7. Updating will occur until 100% is reached on the bar graph . At the prompt, turn the ignition key
OFF for 10 seconds, then turn it ON and select OK.

8. The GOS will confirm that ECM reprogramming is successfully finished . Select OK.
9. If the ECM update was not successful , go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
10. Check for Diagnostic Trouble Codes and erase any OTC .
11 . Start the engine to confirm proper operation .

TSB # : 13-01-017

Page 4 of 7

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

GOS MANUAL MODE ECM UPDATE PROCEDURE

*NOTE
In the event of AUTO MODE update failure (after it initiated the progress bar):
• You must attempt MANUAL MODE. Use the ECM PIN from the vehicle's ECM label if
the correct ECM P/N is not clear from the ROM ID table.
• Replacing an ECM without carefully documenting that a MANUAL MODE update
attempt was made will result in a charge back of your claim.
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN.
2. Select Engine as the system and then select OK.
3. Select Manual Mode and then select NEXT.

4. From the System tab , select Engine and then select NEXT.
5

Update event 288.13MY UD/MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT · ECM will display. Select Next.

6 . Select the correct ROM according to PCM part number on the PCM label. Select Upgrade.
Repair

• Mode
Manu:ilModtt

• System
ENGINE

.. Latest ROM ID

IMD3UP 1MS2D8A

UOJMO 1 8 IMMO, NON ISG . 39101-2EMA3/N3

UD1M D 1.8 NON IMMO, NON ISG. 39103-2EMA31N3
UD!MD 18 NON IMMO t~()N ISG

39103 2EM83/P3 391 07 2EMB3

• Event Group
2UWY~'M!IHJ.Ci'IEEM

D CAUTIO N
• During the ECU U11grade. ob serve U1e folJowin g precautious.

Failure lo foll ow these precautions rnay resul t in ECU damage.
1) DO
2) DO
3) DO
4) DO

NOT operate any other computer program.
NOT disturb or disconnect the DLCCD3ta Link Connector).
NOT turn off the VCI or DO NOT disconnect VCI USB Connector.
NOT start the vehicle or turn the IG key off
5) DO NOT ooerate any of the vehicles other syStems(climate control, lighting.
audio. etc.)

..:I
CneAnllysis

7.

Enter the Password and click OK.
MENU
UD/MD
UD/MD
UD/MD
UD/MD

1.8 IMMO , NON ISG : 39101-2EMA3/N3
1.8 NON IMMO, NON ISG : 39103-2EMA3/N3
1.8 IMMO , NON ISG : 39101-2EMB3/P3, 39105-2EMB3
1.8 NON IMMO , NON ISG : 39103-2EMB3/P3, 39107-2EMB3

IGNITION

PASSWORD

SSB
KEY
SSB
KEY

012 3
032 3
052 3
072 3

8 . If the "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.
9. The remaining steps are the same as Step 7-11 of the Auto Procedure.

TSB #: 13-01-017

Page 5 of 7

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

TCM UPDATE
GOS AUTO MODE TCM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade . If necessary, select the VIN .
2.

Select AT as the system and then select OK.

3. Select Auto Mode and then select Next.

4. From the System tab , select AT and then select OK. The GOS will read the ROM ID . Confirm
the ROM ID is applicable as shown on Page 2, "TCM ROM ID Information".
5. Update event 290.13MY UD/MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVE-TCM will
display. Select Upgrade.

•System

2i0 13'M

UDfl~D

1 3 ACTIVE ECO AC:CELERATIOt l LCGIC IMPRO'IE-TCM

AT

D Event se lec tio n

1. Re vi ew and underst and relate d TSB for vehic le reprogramming .
2. Se lect reprogramming event from Up grade Event pull down menu above .
3. Click t he Upgrade button t o begin ECU up grade .

ID Register
Option Treatment
Data Treatment
Inspection I Test

ECUM!,llping Verilicaion ,

,!,a
6.

=
CHaA!lalys,15

OTC

ClfientOa111

There ewe unused Icons on your desktop ~

~~;r~~':.7tt~~ l» Ytu

,.--,.
ope

Sim,'!:!'on

If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the
vehicle battery by running the engine for 10 minutes.

7. Updating will occur until 100% is reached on the bar graph . At the prompt, turn the ignition key
OFF for 10 seconds , then turn it ON and select OK.

8. The GOS will confirm that TCM reprogramming is successfully finished . Select OK.
9. If the TCM update was not successful , go to GOS MANUAL MODE TCM UPDATE
PROCEDURE.
10. Check for any Diagnostic Trouble Codes and erase any OTC .
11. From the home screen , select Vehicle , AT menu and Option Treatment. Select Resetting Auto
T/A Values and follow the prompts on the screen .
12. Drive the vehicle to confirm proper operation.

TSB # : 13-01-017

Page 6 of 7

SUBJECT:

2013 MY ELANTRA (MD) ECM & TCM UPDATE (SERVICE CAMPAIGN TN3)

I

GOS MANUAL MODE TCM UPDATE PROCEDURE

*NOTE
In the event of AUTO MODE update failure (after it initiated the progress bar):
• You must attempt MANUAL MODE. Use the TCM P/N from the vehicle's TCM label if
the correct TCM P/N is not clear from the ROM ID table.
• Replacing a TCM without carefully documenting that a MANUAL MODE update
attempt was made will result in a charge back of your claim.
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN.

2. Select AT as the system and then select OK.
3. Select Manual Mode and then select NEXT.
4. From the System tab , select AT and then select NEXT.
5. Update event 290.13MY UD/MD 1.8 ACTIVE ECO ACCELERATION LOGIC IMPROVE-TCM will

display. Select Next.

6 Select the ROM according to the part number on the PCM label. Select Upgrade.

ITMDOC18NA9
UD/l\tlD 1 8TCM 3910 1~ 2 E MN3/P3, Z910J..2EMr-J3tP3

• System
AT

• Event Group
~ 1JM YUM.ID 1.BAC TI VEECC

D CAUTI ON
• During the ECU Upgrade. observe the fo ll o wing preca utions.
Fail ure to fo llo w these precau1ions may resu lt in ECU damage.
~

ID Register
Option Trea1ment

1

1) DO NOT operate any other computer program.
2) DO NOT disturb or disconnect the DLCCData Link Connector).
3) DO NOT turn off the VCI or DO NOT disconnect VCI USE· Connector.
4) DO NOT start the vehicle or turn the IG key off.
5) DO NOT operate any of the vehicles other systems(climate control, lighting,
audio. etc.)

Data Treatment
Inspection I Test

.:.1

ECU Mapping V•ification,
~
Set>Jr·

6.

~

05CfUOSCOPI!

S1mT:~oo

Enter the Password and click OK.
UD/MD 1.8 TCM : 39101 -2EMN3/P3 , 39103-2EMN3/P3

7.

If the "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.

8. The remaining steps are the same as Step 7-12 of the Auto Procedure .

TSB #: 13-01-017

Page 7 of 7