GROUP

HyunaRI I

nEWTHlnKlnG.
nEW POSSIBILITIES.

Technical Service Bulletin

NUMBER
13-01-016

CAMPAIGN
DATE

MODEL

MARCH 2013

VELOSTER (FS)

2013 VELOSTER (FS) 1.6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)

Gi).) ®Hvun~m ECU Update
Description: This bulletin provides a procedure to update the ECM and TCM software for 2013
Veloster (FS) 1.6L vehicles to revise the shift feeling in ECO mode .
This TSB supersedes TSB 12-01-043 to include retail vehicles.

*IMPORTANT

.___ _ _ _ ____,*** DEALER STOCK AND RETAIL VEHICLES ***

Dealers must perform this Campaign on all affected vehicles prior to customer retail delivery and
whenever an affected vehicle is in the shop for any maintenance or repair .
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns.
Applicable Vehicles: 2013 MY Veloster (FS) 1.6L with Dual-Clutch Transmissions
Applicable Production Date Range: From May 15, 2012 through October 11, 2012
GOS Information:
Event #
Event #283 (or latest Event#)
Event #284 (or latest Event#)

Description
283.FS OCT REACCELERATION LOGIC IMPROVEMENT - ECM
284 .FS OCT REACCELERATION LOGIC IMPROVEMENT - TCM

Warranty Information:

NOTE: Submit claim on Campaign Claim Entry Screen

39110-28887

YES

GGFS-DFU6FSOOHOO
GGFS-DFU6FS01 HOO
GGFS-DFU6FS02HOO

GGFS-DFU6FS03HOO

NO

GGFS-DFU6ESOOHOO
GGFS-DFU6ES01 HOO
GGFS-DFU6ES02HOO

GGFS-DFU6ES03HOO

VELOSTER
(FS) 1.6L

39110-2BBC7

Circulate To: Service Manager, Warranty Manager, Service Advisors, Technicians, Fleet Repair

SUBJECT:

2013 VELOSTER (FS) l .6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)

TCM ROM ID TABLE: Verify the TCM ROM ID before updating vehicle software.

TCM ROM ID
MODEL

TCM PART NUMBER

PREVIOUS

NEW

VELOSTER (FS)

95440-2A001

DFSOZ16NA9
DFSOZ16NAA

DFSOZ16NAC

GENERAL PRECAUTIONS

•
•

Connect the USB cable between the GOS and
the VCI.
Connect the 16-pin DLC connector from the VCI
into the DLC located under the driver's side
dash.

*NOTE
Make sure the battery icon at the bottom right of the GOS laptop shows at
least 50%; if not, charge the GOS or attach a battery charger.

•

Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories
(including heater/air conditioner/fan, audio, heated seats, rear defroster, etc) to ensure the
battery will not be discharged during the update.

•

Perform the update with the ignition key in the ON position . (Turn the ignition key to the ON
position or press the Start-Stop Button two times without depressing the brake pedal) .

•

Do not disconnect any cables connected to the vehicle or the GOS during the update.

•

Do not start the engine or turn the ignition switch OFF during the update.

*NOTE
Confirm your GOS has the most recent version. If not, connect the GOS to an
Internet port, open the GOS home page and select "Update".
If you encounter GOS related problems, call the GIT Helpline at 888-437-0308.

TSB # : 13-01-016

Page 2 of 6

SUBJECT:

2013 VELOSTER (FS) l.6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)

ECM UPDATE
GOS AUTO MODE ECM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN.
2. Select Engine as the system and then select OK.
3. Select Auto Mode and then select Next.
4. From the System tab, select Engine and then select OK. The GOS will read the ROM ID.
Confirm the ROM is applicable as shown on Page 1, "ECM ROM ID Information".
NOTE: Record the ROM ID in case the auto update fails and a manual update is needed .
5. Update event #283.13MY FS OCT REACCELERATION LOGIC IMPROVEMENT- ECM will
display. Select Upgrade.

~ M od e

Auto Mode

• System
ENGINE

~

L atest ROM ID

2&3 13M'i

os DCT RE ACCELERATION LOGIC

IMPROVEMEMT-E:M

L
D Event selection
1. Review and u nderstand relat ed TSB for vehicle reprogram ming.
2. Select reprogram ming e vent from Upgrad e Event pull down menu above.
3. Click the Upgrade button to begin ECU upgrade.

_____
_:_)

=

OTC

=

CurrentOaui

=
Actuallon
Test

=1
Flighl Record

~
OVOM

1

~
Oscilloscope

~
SimU!ation
Te st

= o

Internet
Update

rltrr..

6. If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the
vehicle battery by running the engine for 10 minutes.
7. Updating will occur until 100% is reached on the bar graph . At the prompt, turn the ignition key
OFF for 10 seconds, then turn it ON and select OK.
8. The GOS will confirm that ECM reprogramming is successfully finished . Select OK.
9. If the ECM update was not successful , go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
10. Check for Diagnostic Trouble Codes and erase any OTC .
11. Start the engine to confirm proper operation.

TSB #: 13-01-016

Page 3 of 6

SUBJECT:

2013 VELOSTER (FS) l .6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)

GOS MANUAL MODE ECM UPDATE PROCEDURE

*NOTE
In the event of AUTO MODE update failure (after it initiated the progress bar):
• You must attempt MANUAL MODE. Use the ECM P/N from the vehicle's ECM label if
the correct ECM P/N is not clear from the ROM ID table.
• Replacing an ECM without carefully documenting that a MANUAL MODE update
attempt was made will result in a charge back of your claim.
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN .
2. Select Engine as the system and then select OK.
3. Select Manual Mode and then select NEXT.
4. From the System tab, select Engine and then select Next.
5. Update event #283 13MY FS DCT REACCELERATIONLOGIC IMPROVEMENT- ECM will
display. Select Next.
6. Select the correct ROM according to ECM part number on the ECM label. Select Upgrade.
Preparation

( •

•Mode
M01nuill Mode

• System
ENGINE

~

l

Event

Diagnosis

Event Ust

C urrent ROM 10

• Latest ROM ID

lGGFS-DFU6ES03HOO

----13MY FS 1.6 DCT IMMO . 3911 0- 2BBB7
13MY FS 1 t; DCT NON IMMO 391 I0.23BC7

•Event Group
283.1lMY FS OCT RHCCELE

ti CAUTION
,._ During the ECU Upgrade. o bserve the fo llowing precautions.
Failure to follow t hese precautions may resu lt in ECU damage.

ID Register
Option Treabnent

1) DO NOT operate any other computer program
2) DO NOT disturb or disconnect the DLC(Data Unk Connector).
3) DO NOT turn off the VCI or DO NOT disconnect VCI USB Connector.
4) DO NOT start the veh icle or turn the IG key off.
5) DO NOT operate any of the vehicles other systems(climate control. lighting.
audio. etc.)

Data Treatment
Inspection I Test

ECU Mzppi~g Verific!lion 1

,!,a•

CllSeAna trsis

!Air S....Oli[:)

7. Enter the Password and click OK.
13 MY FS 1.6 OCT IMMO: 39110-28887
13 MY FS 1.6 OCT NON-IMMO: 39110-288C7
8.

If the "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.

9. The remaining steps are the same as Step 7-11 of the Auto Procedure .

TS8 #: 13-01-016

Page 4 of 6

SUBJECT:

2013 VELOSTER (FS) l .6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)
GOS AUTO MODE TCM UPDATE PROCEDURE

1. From the GDS home page, select ECU Upgrade. If necessary, select the VIN .
2. Select AT as the system and then select OK.
3. Select Auto Mode and then select Next.
4.

From the System tab , select AT and then select OK. The GOS will read the ROM ID . Confirm
the ROM is applicable as shown on Page 1, "ROM ID Information".

5. Update event #284 13NY FS OCT REACCELERATION LOGIC IMPROVEMENT - TCM will
display. Select Upgrade.
P reparation

l~"":;:~Ev~en~tL~iskt~k::=::=::=::=::=J!!!!!

( • Event Group

• Mode
Auto Mode

• System

,. Current ROM ID

IDFSOZ16NAA

• Latest ROM ID

IDFSOZ16NAC

284 13MY 05 DCT REACCELERAT101' LOGIC IM"ROVEMEtJT-TCM

AT

L D Event selection
1. Rev;e w and understand related TSB fo r veh icle reprogramming.
2. Select reprogramming event fro m Upgrade Event pull do wn menu above.
3. Click th e Upgrade button to begin ECU upgrade.

ID Register
Option Treatment
Data Treatment

Inspection I Test
ECU Mapping Verification ;

~~,a•

Cu~

Anlllvsis

OTC

Cment Data

Ac~~!Jt;oo

Flight Record

OVOM

Osdlloscope

Sl"!,-~~oo

6. If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the
vehicle battery by running the engine for 10 minutes.
7. Updating will occur until 100% is reached on the bar graph . At the prompt, turn the ignition key
OFF for 30 seconds , then turn it ON and select OK.

*NOTE
Turn the ignition key off for 30 seconds.
8. The GOS will confirm that TCM reprogramming is successfully finished . Select OK.
9. If the TCM update was not successful , go to GOS MANUAL MODE TCM UPDATE
PROCEDURE.
10. Check for any Diagnostic Trouble Codes and erase any OTC .
11. Drive the vehicle to confirm proper operation.

TSB #: 13-01-016

Page 5 of 6

SUBJECT:

2013 VELOSTER (FS) 1.6L ECM & TCM UPDATE (SERVICE CAMPAIGN TNO)

GDS MANUAL MODE TCM UPDATE PROCEDURE

*NOTE
In the event of AUTO MODE update failure (after it initiated the progress bar):
• You must attempt MANUAL MODE. Use the TCM P/N from the vehicle's TCM label if
the correct TCM P/N is not clear from the ROM ID table.
• Replacing a TCM without carefully documenting that a MANUAL MODE update
attempt was made will result in a charge back of your claim.
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN .

2. Select AT as the system and then select OK.
3. Select Manual Mode and then select NEXT.
4. From the System tab , select AT and then select NEXT.
5. Update event #28413MY FS DCT REACCLERATION LOGIC IMPROVEMENT-TCM will
display. Select Next.
6. 13 MY FS 1.6 DCT TCM 95440-2A001 will display. Select Upgrade.

Event

•Mode
Manual Mode

• System

., Current ROM JO

.,, Latest ROM ID

IDFSOZ16NAC

13Mf FS 1 6 DCT TCM 95440.2AOO ;

AT

• Event Group
m.!3M't rs ocr R:>.cc:LE
IJ CAUTION
• During the ECU Upgrade. obse rve the foll o wing precautions.
Failure to follow these precautions may result in ECU damage.

1) DO NOT operate any other computer program.
2) DO NOT dis1urb or disconnect the DLC(Data Link Connector).

ID Register
Option Treabnent

3) DO NOT turn off the VCI or DO NOT disconnect VCI USB Connector.
4) DO NOT start the vehicle or tum the IG key off.
5) DO NOT operate any of the vehicles other systems(climate control. lighting.
audio. etc.)

Data Treatment
Inspection I Test

ECU Maipmg Ven5ca!on i

"~,a••

~

OTC

CurrE'llt Da1a

Ac!;:s':°°

FliglltRecorcJ

DVOM

I

~

Osdlosrope

~

Slmuiation
T&iol

6. Enter the Password and click OK. The part number can be found on the PCM label.

uim·rn·~
2001

7. If the "Voltage is OK", select OK. If not, select CANCEL and charge the veh icle battery.
8. The remaining steps are the same as Step 7-11 of the Auto Procedure.

TSB #: 13-01-016

Page 6 of 6