NHTSA ID Number: 11032676
Manufacturer Communication Number: 37618.3.3
TSB/Document Date: 2026-05-14
Summary
This is a TJ - Text - plus 2 instruction documents - + 2 PDFS + how to find structure week + flow chart, 6 in all. If the Check Engine Light is on in the DIM and one or more of the DTCs listed below are set, please follow the advice under "Service". 3 steps provided in TJ
Page 18 ( 60 )
Remove the screws.
1.
2.
Torque:
M6 , 10 Nm
Torque:
M8 , 24 Nm
Remove the screw.
Fold marked parts aside.
Torque:
M6 , 10 Nm
TJ Instruction VCC-531608-2
Page 19 ( 60 )
Remove the screw.
Remove the marked part.
Note! Note the position of the component
before removal.
Remove the screws.
Fold marked part aside.
TJ Instruction VCC-531608-2
Page 20 ( 60 )
Disconnect the connector.
Fold marked part aside.
Lift the marked component up
Fold marked part aside.
TJ Instruction VCC-531608-2
Page 21 ( 60 )
Remove the screw.
Fold marked part aside.
Torque:
M6 , 10 Nm
Note! Note the position of the component
before removal.
TJ Instruction VCC-531608-2
Page 22 ( 60 )
Remove the screws.
Torque:
• Stage 1 : Right-hand engine pad to body
frame , 90 Nm
• Stage 2 : Right-hand engine pad to body
frame , 60°
Remove right side the front wheel , refer to:
Removal, replacement and installation
7 - Springs and wheels
77 - Wheels, tyres
770 - complete wheels
Remove the screws.
Remove the clip.
Remove the marked part.
TJ Instruction VCC-531608-2
Page 23 ( 60 )
Remove the screws.
Remove the marked part.
Remove the screws.
TJ Instruction VCC-531608-2
Page 24 ( 60 )
Remove the clips.
Remove the nuts.
TJ Instruction VCC-531608-2
Page 25 ( 60 )
Remove the marked part.
Remove the nut.
Remove the marked part.
TJ Instruction VCC-531608-2
Page 26 ( 60 )
1 . Remove the screws.
2.
Torque:
M6 , 10 Nm
3 . Remove the marked part.
Disconnect the connector.
Loosen the clips.
TJ Instruction VCC-531608-2
Page 27 ( 60 )
Loosen the screws.
Do not remove the screws completely.
Remove the screws.
Remove the marked part.
TJ Instruction VCC-531608-2
Page 28 ( 60 )
Remove the screws.
Remove the marked part.
Torque:
M6 , 10 Nm
Remove the screws.
Remove the marked part.
Torque:
Lower torque rod rear right, to Engine mount
bracket , 110 Nm
TJ Instruction VCC-531608-2
Page 29 ( 60 )
Remove the screws.
Remove the marked part.
Torque:
• Stage 1 : Lower torque rod rear right, to
subframe , 90 Nm
• Stage 2 : Lower torque rod rear right, to
subframe , 120°
Remove the screw.
Torque:
• Stage 1 : Collision member to subframe ,
30 Nm
• Stage 2 : Collision member to subframe ,
90°
TJ Instruction VCC-531608-2
Page 30 ( 60 )
Special Tool: T9997680, Support
Install the Special tool.
TJ Instruction VCC-531608-2
Page 31 ( 60 )
Install the Special tool.
1 . Install the marked component.
2.
Torque:
M12 , 80 Nm
3.
Torque:
M8 , 24 Nm
TJ Instruction VCC-531608-2
Page 32 ( 60 )
Remove the screws.
1.
2.
Torque:
• Stage 1 : Engine mount bracket, to
Cylinder head, M12 , 90 Nm
• Stage 2 : Engine mount bracket, to
Cylinder head, M12 , 90°
Torque:
Engine mount bracket, to Cylinder head,
M10 , 60 Nm
Install the Special tool.
Special Tool: T9997718, Counterhold
TJ Instruction VCC-531608-2
Page 33 ( 60 )
Remove the marked part.
Note! The component can be reused
unless it has been subjected to abnormal
mechanical stress, damage or oil
contamination.
TJ Instruction VCC-531608-2
Page 34 ( 60 )
Lower the engine.
Note! Note the position of the component
before removal.
Remove the screw.
Remove the marked part.
TJ Instruction VCC-531608-2
Page 35 ( 60 )
Extra information
Caution! Make sure that the component is
positioned correctly.
Continue the installation following the steps below.
Remove the screw.
TJ Instruction VCC-531608-2
Page 36 ( 60 )
Disconnect the connector.
Loosen the clips.
Remove the marked part.
Torque:
Lambda probe, tightening , 45 Nm
TJ Instruction VCC-531608-2
Page 37 ( 60 )
Disconnect the connectors.
Remove the cable harness clips.
Fold marked part aside.
Remove the screws.
Remove the marked part.
TJ Instruction VCC-531608-2
Page 38 ( 60 )
Vehicles early version
Caution! The component must be removed
by hand. Tools may not be used.
Note! Use new seals.
Remove the screws.
Remove the marked parts.
Torque:
M6 , 10 Nm
All vehicles
Disconnect the connector.
Remove the screws.
Remove the marked parts.
TJ Instruction VCC-531608-2
Page 39 ( 60 )
Note! Make sure to follow the correct
sequence during installation.
Note! Use a new seal.
Remove the clips.
Remove the screws.
Remove the marked part.
Torque:
M6 , 10 Nm
Install the Special tool.
Pull the component in direction of the arrow.
TJ Instruction VCC-531608-2
Page 40 ( 60 )
Remove the nut.
Torque:
M8 , 24 Nm
Remove the nut.
Torque:
M8 , 24 Nm
TJ Instruction VCC-531608-2
Page 41 ( 60 )
Disconnect the connector.
Remove the screws.
Torque:
M8 , 24 Nm
TJ Instruction VCC-531608-2
Page 42 ( 60 )
Remove the screws.
Remove the marked part.
Hint: It may be necessary to twist or turn
the component.
Torque:
M8 , 24 Nm
Remove the screws.
Remove the marked part.
1.
2.
Torque:
M8 , 24 Nm
Torque:
M10 , 50 Nm
TJ Instruction VCC-531608-2
Page 43 ( 60 )
Note! Make sure that the component is
installed.
Remove the screws.
Torque:
M6 , 10 Nm
TJ Instruction VCC-531608-2
Page 44 ( 60 )
Warning! Be prepared to collect escaping
fluid.
Caution! Make sure that the area around
the component is clean and free of foreign
material.
Note! Make sure that a new component is
installed.
Remove the nuts.
Remove the marked part.
Special Tool: T9814129, Hook wrench
Torque:
• Stage 1 : High-Pressure Fuel Line to Fuel
Pump , 18 Nm
• Stage 2 : High-Pressure Fuel Line to Fuel
Pump , 30 Nm
Remove the Special Tool.
TJ Instruction VCC-531608-2
Page 45 ( 60 )
Release the locks.
Caution! Make sure that the area around
the component is clean and free of foreign
material.
Caution! In order to avoid damage to the
injectors, the part must be carefully pulled
straight up.
Caution! Be extra careful when removing or
installing this component.
Remove the screws.
Remove the part carefully
1.
2.
3.
Torque:
Fuel rail M7 , 22 Nm
Torque:
Fuel rail M8 , 30 Nm
Torque:
M6 , 10 Nm
TJ Instruction VCC-531608-2
Page 46 ( 60 )
Warning! Be prepared to collect escaping
fluid.
Caution! Be extra careful when removing or
installing this component.
Remove the marked parts.
When necessary, perform the following instruction.
Note! Orientation view
Special Tool: T9512943, L-hook
TJ Instruction VCC-531608-2
Page 47 ( 60 )
Caution! In order to avoid damage to the
injectors, the part must be carefully pulled
straight up.
Caution! Be extra careful when removing or
installing this component.
Remove the marked part.
Special Tool: T9512943, L-hook
Replace injector seal , refer to:
Removal, replacement and installation
2 - Engine with mountings and equipment
23 - Fuel system
237 - injector and delivery pipe
Caution! Be extra careful when removing or
installing this component.
Install the marked components.
TJ Instruction VCC-531608-2
Page 48 ( 60 )
Extra information
Caution! Make sure that the mating faces
are clean and free of foreign material.
Caution! Clean carefully, using compressed
air.
Special Tool: T9997505, Cleaning tool
Note! Use new seals.
Remove the screws.
Remove the marked part.
1.
2.
Torque:
M5 , 5 Nm
Torque:
M6 , 10 Nm
TJ Instruction VCC-531608-2
Page 49 ( 60 )
Remove the screws.
Remove the marked part.
Torque:
M6 , 10 Nm
Applies to reassembly of the same component
Note! The component can be reused
unless it has been subjected to abnormal
mechanical stress, damage or oil
contamination.
TJ Instruction VCC-531608-2
Page 50 ( 60 )
Caution! The part is to be reused.
Caution! The part is to be reused.
Continue the removal following the steps below.
Remove camshaft seal , refer to:
Removal, replacement and installation
2 - Engine with mountings and equipment
21 - Engine
215 - transmission
TJ Instruction VCC-531608-2
Page 51 ( 60 )
Loosen each bolt 2 turns at a time until all bolts
are removed.
Remove the marked part.
Vehicles early version
Caution! Note the location of the
component before removal.
Caution! Take extra care when handling the
components.
Remove the marked parts.
TJ Instruction VCC-531608-2
Page 52 ( 60 )
Vehicles late version
Caution! Note the location of the
component before removal.
Caution! Take extra care when handling the
components.
Remove the marked parts.
Cleaning
Caution! Take extra care not to damage the
mating faces.
Caution! Make sure that the oil galleries are
clean and free of foreign material.
Note! Make sure that the mating faces are
clean and free of foreign material.
Use: Putty knife (plastic)
Use: Abrasive cloth , 9511024
Use: Isopropanol ,
TJ Instruction VCC-531608-2
Page 53 ( 60 )
Caution! Take extra care not to damage the
mating faces.
Caution! Make sure that the oil galleries are
clean and free of foreign material.
Note! Make sure that the mating faces are
clean and free of foreign material.
Use: Putty knife (plastic)
Use: Abrasive cloth , 9511024
Use: Isopropanol ,
Installation
Caution! Make sure that the engine oil is to
specification.
TJ Instruction VCC-531608-2
Page 54 ( 60 )
Caution! Make sure that the engine oil is to
specification.
The following steps apply if no damages have
been discovered
Caution! Make sure that the components
are positioned correctly.
TJ Instruction VCC-531608-2
Page 55 ( 60 )
Caution! Make sure that the components
are positioned correctly.
Install the marked component.
Caution! Make sure that the components
are positioned correctly.
TJ Instruction VCC-531608-2
Page 56 ( 60 )
Caution! Make sure that the components
are positioned correctly.
Caution! Make sure that the components
are positioned correctly.
TJ Instruction VCC-531608-2
Page 57 ( 60 )
The following steps are performed on new
component.
Caution! Make sure that the components
are positioned correctly.
Install the marked components.
Caution! Make sure that the components
are positioned correctly.
Install the marked components.
TJ Instruction VCC-531608-2
Page 58 ( 60 )
Caution! Make sure that the components
are positioned correctly.
Caution! Make sure that the components
are positioned correctly.
TJ Instruction VCC-531608-2
Page 59 ( 60 )
All vehicles
Note! The component must be installed within 5 minutes of applying the sealant.
Use: Chemical gasket , 1161771
Caution! Make sure that equal pressure is
applied to the full length of the component.
Note! Make sure to follow the sequence
indicated.
Install the marked component.
Install the screws.
Tighten each bolt 2 turns at a time.
Torque:
M7 , 17 Nm
TJ Instruction VCC-531608-2
Page 60 ( 60 )
Installation
To install, reverse the removal procedure.
Check
Start the engine.
Warning! Make sure that there are no leaks.
Warning! Make sure that there are no leaks.
- Advanced protection against the four main causes of engine...
- Delivers 40% stronger wear protection than industry...
- Provides 15% better deposit defense vs. industry standards...
- Up to 2.5X better heat protection vs. industry standards to...
- Engineered for excellent low-temperature flow, reducing...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 37618.3.3
Replacement Service Bulletin Number:
MFR Communication Date: 2026-04-22
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: UNKNOWN OR OTHER
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
Autoauth, OE-
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.