NHTSA ID Number: 11032056
Manufacturer Communication Number: TB-25-70-01.3
TSB/Document Date: 2026-05-04
Summary
installation instructions for the Orbital (formerly the Distinction) Package trim parts. to be be installed on select new vehicles
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
PURPOSE: This document is provided to remedy a condition where the Orbital (formerly the Distinction) Package trim parts will be installed on the new vehicle. All panels and components of the kits will be described here.
The rocker panels require drilling of fastener holes which is performed at the factory to install the properly.
This document supersedes any and all previous documents relating to the names and locations in workshop
manuals, wiring diagrams, training documents, parts catalog, labor operations, etc.
The racer’s edge wheels and new center caps can be completed at anytime of this package installation, remember to torque the wheels to 220 Nm (162 ft-lbs) Labor time for this is included in the labor
operation below.
Beginning with the Rocker panels. The rocker panel should be lined up with the correct side carbon
cover. The left side rocker panel will be used as an example in this bulletin, the right hand side follows
is symmetrical.
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 1 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Line up holes of the respective panels and Rocker Panel Accent - Black LH C231175000700 (and RH
C231175000800) to be attached to rocker panel.
Use an alcohol wipe to clean the surface of the Rocker Panel before attaching the panel.
The surface must be completely free of grease, dust or any contaminants which may prevent complete
adhesion. Not only will the attachment hardware be used but there are adhesive strips in use for
attachment. (Fig 1)
Install SCREW-PANHEAD TORX M5 X 0.8 X 16.0 PC8 (C140006003200) to be inserted in 4 locations
per side,the left side and right hand rocker panels (0.6 +/- 0.1Nm).
Rocker Panel Accent
Fig 1
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 2 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Use the rocker panel cover as the template for drilling 5 mm diameter holes in to the Rocker panel for
pop rivet installation. Use (part number C143600107200 Rivet-pop 3.2 x 4.8) six (6) pop rivets per side
to secure the carbon fiber panel to the rocker panel. (fig 2)
Fig 2
Continue using a drill to add a pilot hole in the center of the opening of the bracket, as shown (Fig 3a).
Follow with a though hole of 9.5mm +/= 0.5mm through the bracket, this is the through hole to align the
rocker panel carbon accent, LH and RH are symmetrical. The small exhaust cover, is removed and
discarded, on application of the carbon rocker panel cover (Fig 3 b).
Fig 3b
Fig 3a
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 3 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
The rocker cover panel is aligned with the newly drilled hole, and forward stands or guide pins, (Fig 4).
The nut is fastened to 7 +/-3Nm.
Fig 4
Guide pins
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma
Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 4 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
The 8 fastener clips, marked “A” below, C145010100000 (Clip Quarter Turn w Base 9.0) can now be
installed on the panel along the length. The front clip C145000300000 (Clip- Quarter Turn w Base 9.0
Mod) is ahead of the exhaust shroud (marked “B” below). (Fig 4)
A
A
A
Fig 4
B
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 5 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
The Rocker Panel assembly with accent panel can now be installed onto the vehicle body, aligning the
clips to the respective mount locations. Apply firm pressure to snap this assembly in place. (Fig 5)
Fig 5
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 6 of 22
Published: April 2026
TB-25-70-01.3
Type: Technical Bulletin
Year: 2025
System: Body (70)
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Sequence: 01 Revision: 3
The mirror cap can be removed while on the vehicle, removal
of the mirror assembly is not necessary.
The mirror in this guide was placed on a work bench for clarity.
It may help to move the mirror glass with your hands to open
the gap to the housing.
Using a plastic panel tool (Fig. 6) insert into one side of the mirror, and pry one corner or side outwards (Fig 7). This may take
some gentle yet controlled force. To aid in removal of the glass
frame out walk the tool, or fingers, around the mirror, applying
some pressure. Pulling too hard on the outside area of the mirror
is more likely result in breaking glass, start from the side closest to
the vehicle.
Fig 6
Fig 7
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 7 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Once the mirror glass is loose, carefully lower it to
expose the connectors (Fig 8) and disconnect those
from the glass; two connectors on the glass backing
and one white connector (Fig 9).
Fig. 8
Fig. 9
With the mirror glass removed, undo the screws for the surround housing (4, T20 screws reassembly
torque is 1.5Nm). This will provide easier access to the scalp clips, to remove and replace.
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 8 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Four screw locations (Fig. 10).
Fig. 10
The scalp’s clip locations can be seen
(Fig.11).
Use a small tool to help un-clip from the
housing.
Fig. 11
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 9 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Replace the mirror caps with the provided parts (these will be black). begin by removal of the originals
caps (sometimes referred to as scalps, or skull caps). Line up the scalp tabs to the mirror
sub-assembly snap features. An audible “snap” is heard when both parts are fully engaged. Check the
gap consistency to the frame for confirmation of proper installation (fig 12a and fig 12b).
Fig 12a
Fig 12b
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 10 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Remove the front fascia to gain access to the upper grill accent and the grill, or nose piece.
Remove the 10 (ten clips on each liner) begin with the front three body clips, of the wheel liner, on each
side (Fig.13a, Fig. 13b).
Fig 13a
Fig. 13b
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 11 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Continue around the liner and remove the remainder body clips of the wheel liner (Fig.14a, Fig. 14b).
Fig .14a
Fig. 14b
Fig .15a
Fig. 15b
The aluminum wheel liner bracket will stay attached to the wheel liner upon removal (Fig. 15a and
Fig.15b).
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 12 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
With the clips removed, pull down the wheel liner, remove, and set aside (Fig. 16a).
Fig .16a
Proceed to remove the clips for the front fascia (Fig. 10b). Look for 4 clips on the underside, 2 LH and
2 RH (Fig. 16c and Fig. 16d).
Fig. 16b
Fig .16c
Fig. 16d
Karma Automotive Bulletins and service documents are intended for use by experienced and trained Technicians. If you lack the skills, tools, equipment
and a suitable workshop for any procedure described in this document, we suggest you leave such repairs to a Karma retailer and service provider. See
your service provider for advice on whether your vehicle may benefit from the information contained within this document. The information contained in the
Karma Bulletin is accurate at the date of publication. However, Karma Automotive regularly updates technical information. Please check with your Karma
Automotive Retailer and Karma Automotive service provider that the bulletin you intend to use contains the latest available information.
Page 13 of 22
Published: April 2026
TB-25-70-01.3
Title: Orbital Package Install (updated)
Applicability: MY2025 Revero
Type: Technical Bulletin
Year: 2025
System: Body (70)
Sequence: 01 Revision: 3
Remove the (4) 10mm bolts securing LH & RH
side air dams to the front bumper fascia (Fig.
17a). Reassembly Torque is 3.5 Nm.
Fig .17a
Remove the clips securing the LH and RH
side air dams, and center air dam to the
front bumper fascia (Fig.17b).
Fig. 17b
Remove the (6) bolts securing the center air dam to the front bumper fascia (Fig. 17c and Fig. 17d).
Reassembly Torque is 4.5 +/-0.5Nm.
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
- 📌【We are Here for You】Dear valued customer, please be...
- 🚀【5X Faster Next-Level Hardware, Same as MK900/ MX...
- 🔥【3000+ Active Tests = MK900/MK900BT but...
- 📢【2026 U.S. Version, All-in-One as MK808S/ MK808Z...
- 🔥【28+ Hot Services for 150+ Brands】Same as MaxiCOM...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: TB-25-70-01.3
Replacement Service Bulletin Number:
MFR Communication Date: 2026-04-04
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: WHEELS
MFR Component System: body
MFR Component Subsystem: exterior
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.