EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________
Remedy available for
2018-2022 (JL) Jeep Wrangler
2020-2022 (JT) Jeep Gladiator
Template Version 1.0

Revision
2

Edition
March 2026

Detail
New inspection procedure must be performed.

SYMPTOM DESCRIPTION

COMPLETION REPORTING / REIMBURSEMENT

The instrument panel cluster on about 32,587 of the
above vehicles may have an inoperable check
engine/malfunction indicator lamp (CEL/MIL). (JT)
vehicles: CEL/MIL and cargo lamp indicator function
are swapped. (JL) vehicles: CEL/MIL will not turn on.
The CEL/MIL in and of itself will not affect emissions.
However, if there was an emission issue that would
require illumination of the CEL/MIL, the customer
would not be alerted. The vehicle would be noncomplaint to the OBD II regulation.

Claims for vehicles that have been serviced must be
submitted on the DealerCONNECT Claim Entry
Screen located on the Service tab. Claims paid will
be used by FCA to record recall service completions
and provide dealer payments.

SCOPE
NOTE: Some vehicles above may have been
identified as not involved in this recall and therefore
have been excluded from this recall.
IMPORTANT: Some of the involved vehicles may be
in dealer new vehicle inventory. Dealers should
complete this campaign service on these vehicles
before retail delivery. Dealers should also perform this
repair on vehicles in used vehicle inventory and those
vehicles in for service. Involved vehicles can be
determined by using the VIP inquiry process.

REPAIR TO BE PERFORMED
Perform Inspection Procedure first to determine the
functionality of the Instrument Panel Cluster (IPC) and
install a software update only if the defect is present.

ALTERNATE TRANSPORTATION
Dealers should proactively minimize customer
inconvenience while the recall repair is being
performed.
Reference the Goodwill Alternate
Transportation Guidelines warranty bulletin link within
Recall Central on DealerCONNECT for options to
support the customer while their vehicle is in service.

Use the following labor operation numbers and time
allowances:
Labor Description
Perform wiTECH Inspection
Perform wiTECH Inspection
and Update IPC Software to
Most Current Level, 3.5 inch
(Sales Code JAE or JAY)
Perform wiTECH Inspection
and Update IPC Software to
Most Current Level, 7.0 inch
(Sales Code JAL or JAJ)

Number
18-16-C1-81
18-16-C1-82

Hrs
0.2
0.3

18-16-C1-83

0.5

NOTE: See the Warranty Administration Manual,
Recall Claim Processing Section, for complete
recall claim processing instructions.
For Mobile Service Reimbursement, dealer to include
standard dealer entry and mark-up for parts, standard
dealer entry and labor rate for service, as well as the
special services code for mobile allowance. The
special services LOP will only be paid once per VIN
and may NOT be used in coordination with any
Alternate Transportation claims.
For additional details, reference the Mobile Service
Warranty Bulletin - for convenience, a copy has been
linked within Recall Central on DealerCONNECT.

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

1/6

EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________
PARTS INFORMATION
Part No.
04275086AE

Qty.
1

Part Name
Authorized Modification Label

PARTS RETURN
No parts return required for this campaign.

SPECIAL TOOLS
Number
NPN
NPN
NPN

Description
wiTECH MicroPod II / MDP
Laptop Computer
wiTECH Software

DEALER NOTIFICATION
To view this notification on DealerCONNECT, select
“Global Recall System” on the Service tab, then click
on the description of this notification.

OWNER NOTIFICATION / SERVICE SCHEDULING
All involved vehicle owners known to FCA are being
notified of the service requirement by first class mail.
They are requested to schedule appointments for this
service with their dealers. A generic copy of the owner
letter is attached.

VEHICLE LISTS, GLOBAL RECALL SYSTEM, VIP
AND DEALER FOLLOW UP
All involved vehicles have been entered into the
DealerCONNECT Global Recall System (GRS) and
Vehicle Information Plus (VIP) for dealer inquiry as
needed.
GRS provides involved dealers with an updated VIN
list of their incomplete vehicles. The owner’s name,
address and phone number are listed if known.
Completed vehicles are removed from GRS within
several days of repair claim submission.
To use this system, click on the “Service” tab and then
click on “Global Recall System.” Your dealer’s VIN
list for each recall displayed can be sorted by: those
vehicles that were unsold at recall launch, those with
a phone number, city, zip code, or VIN sequence.
Dealers must perform this repair on all unsold
vehicles before retail delivery. Dealers should also
use the VIN list to follow up with all owners to schedule
appointments for this repair.
Recall VIN lists may contain confidential, restricted
owner name and address information that was
obtained from the Department of Motor Vehicles of
various states. Use of this information is permitted for
this recall only and is strictly prohibited from all other
use.

ADDITIONAL INFORMATION
If you have any questions or need assistance in
completing this action, please contact your Service
and Parts District Manager.
Customer Services / Field Operations
FCA US LLC.

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

2/6

EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________
INSPECTION PROCEDURE
NOTE: The wiTECH scan tool must be used to perform this inspection procedure. The wiTECH
software is required to be at the latest release level before performing this procedure.
1. Open the hood. Install a battery charger and verify that the charging rate provides 13.0 to 13.5 volts. Do not
allow the charger to time out during the inspection process. Set the battery charger timer (if so equipped) to
continuous charge.
NOTE: Use an accurate stand-alone voltmeter. The battery charger volt meter may not be sufficiently
accurate. Voltages outside of the specified range will cause unsuccessful wiTECH operation. If
voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC
blower motor to lower the voltage.
NOTE: The vehicle MUST NOT be connected to a high voltage battery charger during the inspection
process.
2. Connect the wiTECH micro pod II / MDP to the vehicle data link connector.
3. Place the ignition in the “RUN” position.
4. Open the wiTECH 2.0 website.
5. Enter your “User id” and “Password” and your “Dealer Code”, then select “Sign In” at the bottom of the
screen. Click “Accept”.
6. From the “Vehicle Selection” screen, select the appropriate vehicle.
7. From the “Action Items” screen, select the “Topology” tab.
8. From the “Topology” tab, select the “IPC” module icon.
9. Within IPC, select “Misc Functions” then select and run the “16C IPC Check” routine.
NOTE: If the mandatory flash “lightning bolt” icon is displayed for the IPC module, DO NOT perform
the flash unless instructed to after following the wiTECH routine instruction steps.
10. After running the routine, one of the following messages will appear:
➢

Flash Not Required Message (Figure 1).

➢

Flash Required Message (Figure 2).

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

3/6

EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________

IPC 22F150 DID Check

The IPC recall is complete, and no further action required. If an IPC update is shown
as available, please do not update.

Close

Figure 1 – Flash Not Required Message
11. If wiTECH displays the “IPC recall is complete, and no further action required” message as shown in
(Figure 1). Disconnect the wiTECH micro pod II / MDP device and battery charger from the vehicle. Install
the Authorized Modifications Label showing that 16C has been completed. For California residents, complete
a vehicle emission recall Proof of Correction Form. Claim the inspection LOP and vehicle may be returned
to the customer or inventory.

IPC 22F150 DID Check

Please flash the IPC with the available 16C Flash.

Close

Figure 2 – Flash Required Message
12. If presented with the “Please flash the IPC with the available 16C Flash” message as shown in (Figure 2).
Proceed to the Service Procedure and Reprogram Instrument Panel Cluster (IPC).

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

4/6

EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________
SERVICE PROCEDURE
Reprogram Instrument Panel Cluster (IPC):
NOTE: The wiTECH scan tool must be used to perform this recall. The wiTECH software is required
to be at the latest release level before performing this procedure. If the reprogramming flash for the
IPC is aborted or interrupted, repeat the procedure. The IPC software must be at the latest software
calibration level after completing this recall.
1. From the IPC tab, select the IPC flash part number. Read the flash special instructions page. Select “OK”
to continue.
2. From the flash ECU agreement page, agree to terms by checking the box.
3. Select “Flash ECU” and then follow the wiTECH screen instructions to complete the flash.
4. Confirm the software is at the latest available calibration level.
5. Cycle the ignition to the “OFF” position let vehicle go into network sleep. Then back to the “RUN” position
before clearing any DTCs that may have been set in any module during the flash process.
6. Click “View DTCs”, select “Clear All DTCs”, click “Continue” and then click “Close”.
7. Place the ignition in the “OFF” position and then remove the wiTECH micro pod II / MDP device from the
vehicle.
8. Remove the battery charger from the vehicle.
9. Install the Authorized Modifications Label showing that 16C has been completed.
10. For California residents, complete a vehicle emission recall Proof of Correction Form.
11. Close the engine compartment hood and return the vehicle to the customer or inventory.

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

5/6

EMISSION RECALL – NORTH AMERICA
Check Engine/Malfunction Indicator Lamp
Reference: 16C

FCA US LLC

_________________________________________________________
Install the Authorized Modifications Label:
Type or print (with a ballpoint pen) the
necessary information onto the
Authorized Modifications Label
indicating 16C has been completed.
Then attach the label near the VECI
label.

Instrument Cluster Software Update
Recall 16C

Figure 1 – Authorized Modifications Label
Authorized Modifications Label

Complete Proof of Correction Form for California Residents:
This recall is subject to the State of California Registration Renewal/Emissions Recall Enforcement
Program. Complete a Vehicle Emission Recall Proof of Correction Form (Form No. 81-016-1053) and
supply it to vehicle owners residing in the state of California for proof that this recall has been
performed when they renew the vehicle registration.
Process Steps to obtain the California Proof of Correction form:
a. Access the “DealerCONNECT” website.
b. Select the “Service” tab.
c. Under the “Publications” heading, select the “ePublishing” link.
d. Sign in using your Dealer Code and Password.
e. Select the “Proof of Correction form”.

Strictly respect STELLANTIS Group safety, cleanliness, and environmental instructions for any vehicle service.
Document exclusively reserved for dealer information. Internal distribution to be ensured by dealer.
Reproduction forbidden without the written agreement of STELLANTIS Group. (C) 2026 STELLANTIS Group. All Rights Reserved

(tdb)

6/6

This notice applies to your vehicle,

[Model Year and Model]

IMPORTANT EMISSIONS RECALL

VIN XXXXXXXXXXXXXXXXX

Malfunction Indicator Lamp

16C
Dear [Name],

LOGO
VEHICLE PICTURE

YOUR SCHEDULING OPTIONS
1. RECOMMENDED OPTION
Call your authorized Chrysler /
Dodge / Jeep® / RAM Dealership.
2. Call the FCA Recall Assistance
Center at 1-800-853-1403. An
agent can confirm part availability
and help schedule an appointment.
3. Visit recalls.mopar.com, scan the
QR code below, or download the
Mopar Owner’s Companion App.

QR Code

FCA US LLC, has determined that certain [2018 through 2022 model year (JL) Jeep® Wrangler and
2020 through 2022 model year (JT) Jeep® Gladiator] vehicles may not be complaint to the OBD II
regulation.
WHY DOES MY VEHICLE NEED REPAIRS?
Your vehicle [1] is equipped with an improperly functioning on-board emission-related
diagnostic system. The Malfunction Indicator Lamp (MIL) may not be working as intended in
your Instrument Panel Cluster (IPC). The MIL in and of itself will not affect emissions.
However, if there was an emission issue that would require illumination of the MIL, the
customer may not be alerted.
HOW DO I RESOLVE THIS IMPORTANT EMISSIONS ISSUE?
FCA US LLC will repair your vehicle free of charge (parts and labor). To do this, your dealer
will inspect and if necessary, reprogram the IPC with the latest software. The estimated repair
time is 30 minutes. In addition, your dealer will require your vehicle for proper check-in,
preparation, and check-out during your visit, which require more time. Your time is important
to us, so we recommend that you schedule a service appointment to minimize your
inconvenience. Ask your dealer for alternate transportation options while your vehicle is in
service. Please bring this letter with you to your dealership.
TO SCHEDULE YOUR FREE REPAIR,
CALL YOUR CHRYSLER, DODGE, JEEP OR RAM DEALER TODAY
CALIFORNIA RESIDENTS
The State of California requires the completion of this emission recall repair prior to vehicle
registration renewal. Your dealer will provide you with a Vehicle Emission Recall Proof of
Correction Form after the Emission Recall service is performed. Be sure to save this form since
the California Department of Motor Vehicles may require that you supply it as proof that the
Emission Recall has been performed.
In order to ensure your full protection under the emissions warranty provisions, it is
recommended that you have your vehicle serviced as soon as possible. Failure to do so could
be determined as lack of proper maintenance of your vehicle.

Get access to recall notifications, locate
your nearest dealer, and more through
this website or Mopar Owner’s
Companion App. You will be asked to
provide your Vehicle Identification
Number (VIN) to protect and verify
your identity. The last eight characters
of your VIN are provided above.
DEALERSHIP INSTRUCTIONS
Please reference Emissions Recall
16C

WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED?
If you have already experienced this specific condition and have paid to have it repaired, you
may visit www.fcarecallreimbursement.com to submit your reimbursement request online. [2]
Once we receive and verify the required documents, reimbursement will be sent to you within
60 days. If you have had previous repairs performed and/or already received reimbursement,
you may still need to have the recall repair performed.
We apologize for any inconvenience, but are sincerely concerned about your satisfaction. Thank
you for your attention to this important matter.
Customer Assistance/Field Operations
FCA US LLC

Mr. Mrs. Customer
1234 Main Street
Hometown, MI 48371

[1] If you no longer own this vehicle, please help us update our records. Call the FCA Recall Assistance Center at 1-800-853-1403 to update your information.
[2] You can also mail in your original receipts and proof of payment to the following address for reimbursement consideration: FCA Customer Assistance, P.O. Box 21-8004,
Auburn Hills, MI 48321-8007, Attention: Recall Reimbursement.