NHTSA ID Number: 11028117
Manufacturer Communication Number: LI14.30-N-075882
TSB/Document Date: 2026-02-03
Summary
Complaint Check engine warning light is active. The following fault codes may be present in the engine control unit: • P3007F1 Leak detected in the intake air system or • P3007F2 Mass air flow malfunction in the intake air system (cylinder bank 1) or • P300CA8 Leak detected in the intake air system or • P300CA9 Mass air flow malfunction in the intake air system (cylinder bank 1) or • P300CA9 and P3007F1: Faults are present simultaneously in the quick test In addition, the customer may report: • An “air leak” type noise from the engine compartment/intake air area, and/or • A “chugging” noise, especially during acceleration or under load. These noise complaints can be present with or without the above fault codes. Cause Causes for FC P3007F1 or P300CA8: Faults are set if: • If there is a leakage upstream of the exhaust gas turbocharger (see "Dichtring_Sealant.jpg"). • If the housing intermediate flange at the high-pressure EGR valve (where the exhaust back pressure sensor connects) is carbonized or clogged, or if there is carbonization/incomplete sealing of the high-pressure or lowpressure EGR valves. (See “Gehaeusezwischenflansch_intermediate_flange.jpg” and verstopfter_Gehaeusezwischenflansch_clogged_Intermediate_Flange.jpg.”) • Note: Only relevant if the correction value in load range 1 is less than -8%. • If the intake manifold (charge air distribution line) or charge air cooler is carbonized (see "Saugrohr_intake_manifold.jpg"). • If engine timing is misadjusted. • There is a defective hot film mass air flow sensor or a hot film mass air flow sensor that is affected by incorrect airflow (this can be due to a clogged or deformed air filter). Refer to the attached file "Luftfilter_air_filter." Cause of fault code combination P300CA9 AND P3007F1: Faults are set if: • There is carbonization or incomplete closure of the high-pressure exhaust gas recirculation valve, especially in the housing intermediate flange at the EGR valve (linked to the exhaust back pressure sensor). Charleston Plant Identification – VIN 11th Digit “T”: For vehicles produced at the Charleston Plant (identified by “T” in the 11th digit of the VIN) with a production date on or after 12/20/2023: • If fault code P3007F1 or P300CA8 is set, an air leak is found, and the cause is identified as a loose or mis-installed Clean Air Line from the factory, open an Initial Field Quality (Info Only) case. • Include the current Quick Test and photos showing the Clean Air Line issue. For all other vehicles, continue diagnosis as per the standard instructions.
Check engine light active - Fault P3007F1, P3007F2,
P300CA8, or P300CA9 present in CDI control unit
Topic number
LI14.30-N-075882
Version
7
Function group
14.30 - Secondary air injection
Date
1/23/26
Validity
Model 907 with engine 654
Reason for change
Complaint update
Complaint
Check engine warning light is active.
The following fault codes may be present in the engine control unit:
•
•
•
•
•
P3007F1 Leak detected in the intake air system or
P3007F2 Mass air flow malfunction in the intake air system (cylinder bank 1) or
P300CA8 Leak detected in the intake air system or
P300CA9 Mass air flow malfunction in the intake air system (cylinder bank 1) or
P300CA9 and P3007F1: Faults are present simultaneously in the quick test
In addition, the customer may report:
•
An “air leak” type noise from the engine compartment/intake air area, and/or
•
A “chugging” noise, especially during acceleration or under load.
These noise complaints can be present with or without the above fault codes.
Cause
Causes for FC P3007F1 or P300CA8:
Faults are set if:
•
•
•
•
•
•
If there is a leakage upstream of the exhaust gas turbocharger (see "Dichtring_Sealant.jpg").
If the housing intermediate flange at the high-pressure EGR valve (where the exhaust back pressure sensor
connects) is carbonized or clogged, or if there is carbonization/incomplete sealing of the high-pressure or lowpressure EGR valves. (See “Gehaeusezwischenflansch_intermediate_flange.jpg” and “verstopfter_Gehaeusezwischenflansch_clogged_Intermediate_Flange.jpg.”)
Note: Only relevant if the correction value in load range 1 is less than -8%.
If the intake manifold (charge air distribution line) or charge air cooler is carbonized (see "Saugrohr_intake_manifold.jpg").
If engine timing is misadjusted.
There is a defective hot film mass air flow sensor or a hot film mass air flow sensor that is affected by incorrect
airflow (this can be due to a clogged or deformed air filter). Refer to the attached file "Luftfilter_air_filter."
Cause for FC P3007F2 or P300CA9:
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 1 / 12
Faults are set if:
•
•
•
•
There is a leak downstream of the exhaust gas turbocharger.
The charge air distribution line (intake manifold) is heavily carbonized (see "Saugrohr_intake_manifold.jpg").
There is carbonization or incomplete closure of the high-pressure exhaust gas recirculation valve, especially in
the housing intermediate flange at the EGR valve (linked to the exhaust back pressure sensor).
There is a defective hot film mass air flow sensor, or it is affected by incorrect airflow due to a clogged or deformed air filter
(see "Luftfilter_air_filter").
Cause of fault code combination P300CA9 AND P3007F1:
Faults are set if:
•
There is carbonization or incomplete closure of the high-pressure exhaust gas recirculation valve, especially in
the housing intermediate flange at the EGR valve (linked to the exhaust back pressure sensor).
Charleston Plant Identification – VIN 11th Digit “T”:
For vehicles produced at the Charleston Plant (identified by “T” in the 11th digit of the VIN) with a production date on
or after 12/20/2023:
•
If fault code P3007F1 or P300CA8 is set, an air leak is found, and the cause is identified as a loose or mis-installed Clean Air Line from the factory, open an Initial Field Quality (Info Only) case.
•
Include the current Quick Test and photos showing the Clean Air Line issue.
For all other vehicles, continue diagnosis as per the standard instructions.
Remedy
In the case of fault code P3007F1 or P300CA8:
1) Check for Required ECU Software Update (Applies to P300CA8 only)
For vehicles with:
•
•
•
Code MU6 (dual-stage turbocharger) and CDI control unit N3/40 with software release G090:
Update the CDI Control Unit software to the latest version.
If the CDI control unit software is already up to date, continue to the steps below.
2) Verify Clean Air Line & Intake System Assembly
•
•
•
•
•
•
Inspect the clean air line between the air filter housing and the exhaust gas turbocharger for proper assembly.
Reference WIS documents: AR09.10-S-8130EA, AR09.40-S-0500EA (dual-stage turbo), AR09.20-S-0010EA,
and/or AR09.41-S-6817EA.
Confirm correct assembly and all connections:
Ensure proper seating and locking of all quick-release couplings (see provided images and WIS refs).
For dual-stage turbochargers, confirm the cast lug aligns with the tab. (See picture 1c.)
Note: Always replace the red sealing ring (see annex "Dichtring_Sealant_nok") during assembly/repairs.
3) Charge Air System / Intake Leak Check
•
•
•
•
Preferably, pressurize the system to 0.25 bar from the exhaust end pipe, with the intake air system sealed (see
"Adapter_Reinluftleitung_Clean_Air_Line_Model_Type_907").
Alternatively, use Xentry Diagnostics:
CDI Control Unit N3/40 → Tests → Manual Leak Test of the Charge Air System.
Optional: Use leak tester part number 000 588 18 21 00 (see WS09.00-P-0028B) to perform flue gas diagnosis
for leaks in the intake air system with UltraTraceUV. For more information, see WIS/WSM: Contents → Model
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 2 / 12
•
Series → Van → V-Class / Vito → 09 - Air Intake, Charging → AD - Flue Gas Diagnosis for Leaks with UltraTraceUV.
If leaks are found, carry out necessary repairs.
4) Inspect Sealing Ring and Connections
•
•
Inspect the sealing ring between the exhaust gas turbocharger and the clean air line for damage with an endoscope (see annex "Dichtring_Sealant_nok").
Repair/replace as needed.
5) Visual Inspection for Carbonization/Damage
•
•
•
•
•
•
•
Inspect the following for severe carbon build-up or other inconsistencies:
Intake manifold (charge air distribution line) – see "Saugrohr_intake_manifold.jpg."
Housing intermediate flange at the high-pressure EGR valve (exhaust back pressure sensor connection, use a
flashlight).
Only necessary if the air intake correction value in load range 1 is less than -8%.
Charge air cooler.
Initiate repairs/cleaning as needed.
If issues are found in the intake manifold, also check the cylinder head intake ports.
6) Inspect Air Filter and MAF Sensor
•
•
•
Visually inspect the air filter for blockages, severe soiling, deformation, or damage (see "Luftfilter_air_filter").
The fault may be set if the hot film mass air flow sensor (MAF) element is oiled.
Replace air filter/MAF as needed.
7) Engine Timing
•
•
For vehicles with mileage over 90,000 km / 150,000 km, or with prior control assembly repairs:
Check and adjust engine timing as needed.
8) EGR Valve and Cooler Functional Checks
•
•
•
•
Actuate high-pressure and low-pressure exhaust gas recirculation (EGR) valves with Xentry Diagnostics.
Check their functionality and visually inspect all related parts for carbonization.
Replace any affected parts.
If significant issues are found with the low-pressure EGR valve, also clean just downstream of the DPF and
check/clean the low-pressure EGR cooler for carbon accumulation.
9) Finalize Repairs, Reset & Verification
1. Reset Correction Factors (Air Mass of Intake System):
•
CDI Control Unit N3/40 → Adaptations → Teach-in Processes → Reset Learned Values → Intake Air System.
2. Quick Test and Clear Fault Memory:
•
Conduct a system quick test and clear fault codes (see AD00.00-S-2000-04E).
•
Important: Reset correction factors before clearing memory; otherwise, fault codes may recur.
3. Disconnect Diagnostic Device:
•
As specified in AD00.00-S-2000-04E.
In the case of fault code P3007F2 or P300CA9:
1) Check for Required ECU Software Update (P300CA9 only)
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 3 / 12
For vehicles with:
•
•
•
Code MU6 (dual-stage turbocharger) and CDI control unit N3/40 with software release G090:
Update the CDI control unit software first.
If the CDI control unit software is already up to date, continue to the steps below.
2) Charge Air System / Intake Leak Check
•
•
•
•
•
Preferably, pressurize the system to 0.25 bar from the exhaust end pipe, with the intake air system sealed (see
"Adapter_Reinluftleitung_Clean_Air_Line_Model_Type_907").
Alternatively, use Xentry Diagnostics:
CDI Control Unit N3/40 → Tests → Manual Leak Test of the Charge Air System.
Optional: Use leak tester part number 000 588 18 21 00 (see WS09.00-P-0028B) to perform flue gas diagnosis
for leaks in the intake air system with UltraTraceUV. For more information, see WIS/WSM: Contents → Model
Series → Van → V-Class / Vito → 09 - Air Intake, Charging → AD - Flue Gas Diagnosis for Leaks with UltraTraceUV.
If leaks are found, carry out necessary repairs.
3) Visual Inspection of Intake Manifold and System Components
•
•
•
•
•
•
•
•
•
Inspect the charge air distribution line (intake manifold) for carbon buildup.
Inspect the following (especially for P300CA9, but advisable for thoroughness):
High-pressure EGR valve
High-pressure EGR cooler (A6541409000)
EGR pipe (A6541400702)
Charge air mixing pipe (A6540902000) and intake manifold (charge air distribution line)
Housing intermediate flange (A6541407000)
Exhaust back pressure sensor area
Check all for carbonization, consistency, and proper installation. If any significant issues are found, perform necessary cleaning or repair measures.
4) Inspect Air Filter and MAF Sensor
•
•
•
Visually inspect the air filter for blockages, severe soiling, deformation, or damage (see "Luftfilter_air_filter").
The fault may be set if the hot film mass air flow sensor (MAF) element is oiled.
Replace air filter/MAF as needed.
5) Finalize Repairs, Reset & Verification
1. Reset Correction Factors (Air Mass of Intake System):
•
CDI Control Unit N3/40 → Adaptations → Teach-in Processes → Reset Learned Values → Intake Air System.
2. Quick Test and Clear Fault Memory:
•
Conduct a system quick test and clear fault codes (see AD00.00-S-2000-04E).
•
Important: Reset correction factors before clearing memory; otherwise, fault codes may recur.
3. Disconnect Diagnostic Device:
•
As specified in AD00.00-S-2000-04E.
In the case of fault code combination P300CA9 and P3007F1:
1)Inspect the housing intermediate flange on the high-pressure exhaust gas recirculation (EGR) valve, specifically at
the connection for the exhaust back pressure sensor. Use a flashlight to check for any inconsistencies or carbon buildup.
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 4 / 12
2) Finalize Repairs, Reset & Verification
1. Reset Correction Factors (Air Mass of Intake System):
•
CDI Control Unit N3/40 → Adaptations → Teach-in Processes → Reset Learned Values → Intake Air System.
2. Quick Test and Clear Fault Memory:
•
Conduct a system quick test and clear fault codes (see AD00.00-S-2000-04E).
•
Important: Reset correction factors before clearing memory; otherwise, fault codes may recur.
3. Disconnect Diagnostic Device:
•
As specified in AD00.00-S-2000-04E.
References:
•
•
•
WIS documents as above
Visual aids and annexed images as referenced in the procedure
For details, consult vehicle-specific service documents and Xentry updates
Attachments
File
Description
Dichtring_Sealant.jpg
Gehaeusezwischenflansch_Intermedidate_Flange.jpg
Luftfilter_air_filter.jpg
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 5 / 12
Adapter_Reinluftleitung_Clean_Air_Line_Model_Type_907.jpg
verstopfter_Gehaeusezwischenflansch_clogged_Intermedidate_Flange.jpg
Saugrohr_Intake_manifold_II.jpg
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 6 / 12
Saugrohr_Intake_manifold.jpg
Einlasskanaele_ZK_inlet_ports_CH.jpg
2b.JPG
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 7 / 12
2c.JPG
1c.JPG
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 8 / 12
1b.JPG
2a.JPG
1a.JPG
2d.JPG
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 9 / 12
3.JPG
4.JPG
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 10 / 12
WIS-References
Document number
Title
Note
AR09.10-S-8130EA
Remove/install engine intake air duct
downstream of air filter
26.03.2024
AR09.40-S-0500EA
Remove/install air intake duct upstream of turbocharger
26.03.2024
AR09.20-S-0010EA
Remove/install resonance chamber
01.08.2023
AR09.41-S-6817EA
Remove/install charge air cooler
26.03.2024
AR09.10-D-8130TSM
Remove/install engine intake air duct
downstream of air filter
27.07.2022
AR09.40-D-0500TSM
Remove/install air intake duct upstream of turbocharger
29.07.2022
AD00.00-S-2000-04E
Connect STAR DIAGNOSIS and read
out fault memory
WS09.00-P-0028B
000 588 18 21 00 Leak tester
20.02.2023
Disclaimer
NOTE: The information contained in this document is intended for use by trained, professional technicians with the
knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz
approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and
provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect
is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a
symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes
resulting in the same or similar symptoms or conditions described in this document, and trained professional service
02.02.2026 15:48
© Copyright Mercedes-Benz AG
CCUSHWA
Page 11 / 12
technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained
in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
Symptoms
Power generation > Engine management > Indicator lamp > Engine diagnosis > lit
Control unit/fault code
Control unit
Fault text
N3/40 - Motor electronics 'MRD1' for combustion engine
'OM654' (CDI) (MRD1NFZ)
P3007F2 - The air mass flow in the intake air system (cylinder bank 1) has a malfunction.
P3007F1 - A leak was detected in the intake air system.
P300CA9 - The air mass flow in the intake air system (cylinder bank 1) has a malfunction.
P300CA8 - A leak was detected in the intake air system.
Operation numbers/damage codes
Op. no.
Operation text
02.02.2026 15:48
© Copyright Mercedes-Benz AG
Time
CCUSHWA
Damage
code
Note
Page 12 / 12
- Advanced protection against the four main causes of engine...
- Delivers 40% stronger wear protection than industry...
- Provides 15% better deposit defense vs. industry standards...
- Up to 2.5X better heat protection vs. industry standards to...
- Engineered for excellent low-temperature flow, reducing...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: LI14.30-N-075882
Replacement Service Bulletin Number:
MFR Communication Date: 2026-01-23
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.