Field campaign
Topic

Software Update | BiL 5.3.1 v1 to v2 | Flying Spur | 25MY (SC25/11)

Market area

Bentley: worldwide (2WBE),China 796 VW Import Comp. Ltd (Vico), Beijing (6796)

Brand

Bentley

Transaction No.

2077583/7

Campaign number ED42
Note
Type
US code

Vehicle data
25MY Flying Spur
Sales types

Type MY

Brand Designation Engine code Gearbox code Final drive code

Z32* 2025 E

Documents
Document name
master.xml
ed42vinlist.pdf

*

*

*

ED42

Transaction No.: 2077583/7

Software Update | BiL 5.3.1 v1 to v2 | Flying Spur | 25MY (SC25/11)

Notes

Release date: Nov 14, 2025

Repair instructions

Technical background
Software updates must be applied to update the vehicles Baseline Integration Level (BiL).
The software update corrects the following Diagnostic trouble codes (DTCs):
•

P060100: High Voltage Battery (Address 008C) Internal Control Module Memory Checksum Error

•

P057F00: Battery "A" State of Charge Performance, B11B300 Igniter for high voltage battery interrupt

•

P0A0B00: High Voltage System Interlock Circuit Performance (HVIL).

CAUTION
If the ED35 Campaign is showing as outstanding in ElsaPro, the ED35 campaign MUST be completed first.
– If ED35 is not completed first, this update will not succeed.

Remedy
The instructions within the ‘Work’ section must be conducted to completion.

Customer notification
Please ensure all applicable instructions are conducted at the nearest opportunity.

Warranty
SVM Update Time
Claim type: 790 or 710
Service number: ED42
Damage code: 0066
Criteria:01
Labour Operation Code: 01 51 00 00
Time: As per ODIS log (Must not exceed 200TU)
Additional Time Allowance
A 100TU allowance may be claimed only if a SVM update fails to complete successfully. This is intended to
cover additional diagnostic or recovery work directly resulting from the failed update. It must not be used for
unrelated delays or issues.

ODIS logs must be attached to a DISS ticket for evidence of failure. Claims without valid documentation will
be rejected. Warranty Adjudicators will review associated ODIS logs and DISS queries to determine actual
software update time.

Parts
Not Applicable

Parts supply
Not Applicable

Parts despatch control
Not Applicable

Repair instructions

Notes

Technical background
Software updates must be applied to update the vehicles Baseline Integration Level (BiL).
The software update corrects the following Diagnostic trouble codes (DTCs):
•

P060100: High Voltage Battery (Address 008C) Internal Control Module Memory Checksum Error

•

P057F00: Battery "A" State of Charge Performance, B11B300 Igniter for high voltage battery interrupt

•

P0A0B00: High Voltage System Interlock Circuit Performance (HVIL).

CAUTION
If the ED35 Campaign is showing as outstanding in ElsaPro, the ED35 campaign MUST be completed first.
– If ED35 is not completed first, this update will not succeed.

Check
Check if the vehicle is already listed as repaired in “Repair history" (in ElsaPro).
Please also refer to the “Identification” section and check if a paint identification mark is evident in the
vehicle.
If the vehicle is not shown in ElsaPro as repaired, and the identification mark is not present, please conduct
the instructions within the ‘Work’ section to completion

Parts
Not Applicable

Work

CAUTION
The Bentley ODIS-S Brand Version MUST be at least 2.35.1 (or higher)

CAUTION
Before conducting the onward instructions, the operative MUST recheck the communication method in
ODIS and ensure that DoIP is selected before proceeding. Within ODIS-S, perform the following:
– On the right hand side, select the “Admin” tile (Within ‘Operating modes’)
– Select “GFF sequence” (Within ‘General information’ section)
– Under the “Selection of Communication path” drop-down menu, select “Only permit DoIP
communication”.

CAUTION
DO NOT, UNDER ANY CIRCUMSTANCES, ATTEMPT TO CONDUCT THE SOFTWARE UPDATE VIA
THE CAN NETWORK. ONLY DoIP SHOULD BE USED WHEN PERFORMING THE SVM UPDATE.

CAUTION
You MUST ONLY use the Diagnosis Interface VAS 6154 (WiFi Diagnostic Tool) in USB OPERATION or
the CABLE-CONNECTED VAS 5055 for the reprogramming (updating) of the control units.
– If neither of these units are available, the VAS 5054 (A) may be used in USB MODE.
– DO NOT under any circumstances use a Bluetooth connection to conduct the reprogramming
(updating) of any control units.

Battery Charger
CAUTION
ONLY Chargers that meet the approved specification on the Mandatory Equipment List (available on the
Bentley Hub) MUST be used.
– The charger must be set to a mode where a MINIMUM of 90a is supplied to the battery during the
process. Typically, this is known as ‘Power Supply Mode’ or ‘DIAG+ Mode’.
– A voltage of exactly 14.8v must be set and maintained throughout the process.
– Please refer to the manual to ensure that these requirements are met before beginning any SVM
update

Preparation Before Update
WARNING
Hybrid Vehicles use a High Voltage System and therefore MUST ONLY be worked on by suitable
personnel

CAUTION
During the update, switch off all unnecessary consumers. For example, ventilation, seat heaters, interior
illumination, exterior lights ect.

Conduct a full guided fault find of the vehicle.
If a ‘Check Installation List’ pop-up appears, select ‘close’ (see below image)

Referring to TPI 2075920, address any unknown faults BEFORE conducting any of the below updates.
Ensure that the correct battery charger is connected to the vehicle. – Refer to the ‘’Battery Charger’’ Section
above.

Obtaining Hotfix for ODIS-S
Visit https://bentley.atheer.io/ and log in with the following case-sensitive account details.
•

Username: bilupdate

•

Password: Bentley123!
NOTICE

If you are already logged into your retailer account, you will need to logout first. To do this, click on your
account initials (bottom left corner) and click “Sign Out”.
After logging in, using the navigation bar on the left hand side, click on the ‘conversations’ tab

Next, click the conversation named “ED42 Hotfix”

NOTICE
You MUST NOT leave the conversation, remove users from the conversation, delete the conversation or
alter the conversation in any way. The ONLY action you are permitted to perform is download the
applicable file required for this campaign.

In this conversation, you will find a file named “ED42 _Hotfix” and “ED42_Local_Flash_Files”.
Left click each of the file names and download each folder.

After left-clicking the files to download them, the download will take circa 5-10 minutes, do not interrupt this
process. You may need to wait a short period (internet speed dependent) for the files to download.

During/before the download commences, there may be a warning about a "pop-up" being blocked which will
prevent the file from downloading, ensure to select option "Allow Pop-Ups from this website" to download the
file. Wording may differ depending on web browser.

Locate the download file and extract it. To do this, right click the file, click “7 zip” and then “Extract here”

After successfully downloading the file, please logout of the account.

Loading ODIS-S Hotfix
With the hotfix you have downloaded from Atheer (ED42_Hotfix), load the hotfix ‘‘E_2.35.1
_HF_BMC_BJB_204_207_V2_20250403-140521’ into ODIS-S.
The Bentley ODIS-S Brand Version MUST be at least 2.35.1 (or higher).

With the ‘ED42_Local_Flash_Files’, copy the content of the folder into your root c:/temp drive on your ODIS
device.
•

FL_4M0915249AN_0201_UPD0004T0005_V001_S.odx

•

FL_4M0915249AM_0207_ABJB7A60590M1_V001_S.odx

•

FL_4M0915231AH_0204_XHX15EV0421M6_V001_S.odx

First SVM Code Input
CAUTION
At this point, a suitable battery charger must be connected to the vehicle.

1. In ODIS-S, navigate to the “Special Functions” tab.
2. Navigate to ‘SVM – Code Input’, enter the SVM Code: “373ED4201”.
3. On the next screen, ensure that the SVM code displayed is correct.

4. You will be shown the communication type. This MUST be set to “DoIP”.
a. If “DoIP” is not selected, select option 3 until the communication type is set to “DoIP”.

5. After ensuring DoIP is selected, and a suitable battery charger is connected, select Option 1 – “Yes”.
a. From here, all control modules will be interrogated and the SVM action will take place.

6. Ensure that the diagnostic device remains connected for the duration of the update.

7. Follow all on-screen prompts until the program ends.
a. If you have a prompt stating there is no communication established with 00CC, select done/continue.

8. Follow the on-screen instructions to completion. If you do not encounter any errors, please proceed to the
“HIGH VOLTAGE SHUTDOWN” section.

NOTICE
If you receive an error code: 8088, you must follow the below instructions.

1. In ODIS-S, navigate to the “Special Functions” tab.
2. Navigate to ‘SVM – Code Input’ and enter the SVM code: “373A5CONFIG01”
3. On the next screen, ensure that the SVM code displayed is correct.

4. You will be shown the communication type. This MUST be set to “DoIP”.
a. If “DoIP” is not selected, select option 3 until the communication type is set to “DoIP”.

5. After ensuring DoIP is selected, and a suitable battery charger is connected, select Option 1 – “Yes”.
a. From here, all control modules will be interrogated and the SVM action will take place.

6. Ensure that the diagnostic device remains connected for the duration of the update.

7. Follow all on-screen prompts until the program ends.
a. If you have a prompt stating there is no communication established with 00CC, select done/continue.

8. You may or may not encounter an error after the update. Proceed regardless.

9. Refer back to the start of “First SVM Code Input” and repeat the process to input the SVM code
“373ED4201”.

10. Perform a whole vehicle DTC clear by exiting the current diagnostic session.

11. Perform a 15 minute CAN bus sleep.
a. Turn off the ignition.
b. Remove all equipment from the car (Diagnostic tester/dongle, battery charger, keys).
c. Close all doors, windows, bonnet and boot lid.
d. Lock the vehicle to perform a CAN-BUS sleep (wait 15 minutes).

12. Re-run guided fault finding and clear DTCs

High Voltage Shutdown
WARNING
De-energise the high-voltage system via ODIS-S. Refer to ElsaPro, Repair Group 93 – “De-energising
high-voltage system” to do so.

1. After de-energisation, Refer to ElsaPro Repair Group 70 ‘Boot carpet – To remove and fit’. Remove the
boot floor and gain access to the earth cable from the 12v battery negative and the body in white (This
access will be required later in the test plan).

2. Navigate to ‘Special functions’ and select ‘SVM – Pre 372BIL5201 Hotfix Routines’, then ‘Perform test’.

3. Switch to ‘DoIP’ when prompted.

4. Select ‘1) BMC/BJB 204/207 Update Repair’ and follow the on-screen instructions.
•

When the tester attempts to flash ‘008C - Battery regulation control module’ you may receive a
message informing you that the pre-conditions have not been met. Select ‘done/continue’.

•

On the following screen (shown below) select option 2 to attempt to flash the ECU – this should allow
the ‘008C - Battery regulation control module’ to flash successfully.

•

If the flash fails, perform the below actions.

1. Exit the test.

2. Allow the car to sleep for 5 minutes.
a. Turn off the ignition.
b. Remove all equipment from the car (Diagnostic tester/dongle, battery charger, keys).
c. Close all doors, windows, bonnet and boot lid.
d. Lock the vehicle to perform a CAN-BUS sleep (wait 5 minutes).

3. Clear DTCs from ‘008C - Battery regulation control module’.
3a. To do this, right click on control unit 008C, click Guided Functions and then click ‘Clear Fault Memory’.

4. Return to ‘Special functions’ and run the test plan ‘SVM – Pre 372BIL5201 Hotfix Routines’.

5. Within this test plan, select option 2 and run until completion.

6. Once the test has been completed, right click on control unit 008C and select guided functions. Then, read
ECU Identification and ensure that the 06D0 (Battery Junction Box) appears as a subsystem within the read
identification test plan.

7. Continue to the next SVM update.

Final SVM Code Input

WARNING
Re-energise the high-voltage system via ODIS-S. Refer to ElsaPro, Repair Group 93 – “Re-energising
high-voltage system” to do so.

1. After re-energising the High Voltage System, navigate to the “Special Functions” tab in ODIS-S.
2. Navigate to ‘SVM – Code Input’ and enter the SVM Code: “373531COM02”.

3. On the next screen, ensure that the SVM code displayed is correct.

4. You will be shown the communication type. This MUST be set to “DoIP”.
a. If “DoIP” is not selected, select option 3 until the communication type is set to “DoIP”.

5. After ensuring DoIP is selected, and a suitable battery charger is connected, select Option 1 – “Yes”.
a. From here, all control modules will be interrogated and the SVM action will take place.

6. Ensure that the diagnostic device remains connected for the duration of the update.

7. Follow all on-screen prompts until the program ends.
a. If you have a prompt stating there is no communication established with 00CC, select done/continue.

8. Follow the on-screen instructions to completion.

9. If you are presented with this screen (Fig 3) at the end of the update, the update was successful. Please
continue to step 11.

Fig 3

10. If you encounter any errors during the update, please refer to TPI 2078962 - ‘ODIS Error Message – Best
Practice When Performing Baseline (BiL) Updates’.
a. Please raise a FULL TECHNICAL DISS query.
b. Customer Statement: “ED42 Support”
c. Workshop Findings: Give a summary of the error encountered and ensure that the latest Guided Fault
Finding log is submitted online.

11. After successful completion of the update, perform the following.
a. Turn off the ignition.
b. Remove all equipment from the car (Diagnostic tester/dongle, battery charger, keys).
c. Close all doors, windows, bonnet and boot lid.
d. Lock the vehicle to perform a CAN-BUS sleep (wait 15 minutes).

12. After 15 minutes, unlock and open the driver’s door. Turn on the ignition, re-connect the battery charger
and diagnostic dongle.

13. Re-run guided fault finding and clear DTCs. If any faults are present, refer to TPI 2075920. If any other
faults are present, please raise a full DISS query with a fill GFF log uploaded online stating the error
encountered.

Identification
Once the applicable action has been conducted, the operative must submit a warranty claim as this will show
the service campaign action as complete within Elsa Pro “Repair history”.

You must also add a blue paint mark as per the picture below.

Repair instructions

Notes

INTERNAL

#

AMERICAS

ASIA PACIFIC

CHINESE MAINLAND HK AND MACAO

SCBBR6ZG0SC020013

SCBBF53S0SC021579

SCBBF53S1SC021557

SCBBR6ZG0SC020030

SCBBF53S0SC021811

SCBBF53S1SC021588

SCBBR6ZG0SC020111

SCBBF53S1SC021543

SCBBF53S1SC021669

SCBBR6ZG0SC020657

SCBBF53S1SC021977

SCBBF53S4SC021598

SCBBR6ZG0SC021209

SCBBF53S4SC021472

SCBBF53S6SC021571

SCBBR6ZG0SC021212

SCBBF53S6SC021926

SCBBF53S9SC021628

SCBBR6ZG0SC021498

SCBBF53S6SC022249

SCBBG53S0SC021269

SCBBR6ZG0SC021534

SCBBF53S7SC021949

SCBBG53S0SC021286

SCBBR6ZG0SC021596

SCBBF53S9SC021886

SCBBG53S0SC021305

SCBBR6ZG0SC021758

SCBBF53SXSC021959

SCBBG53S0SC021319

SCBBR6ZG0SC022084