SERVICE BULLETIN
Subject: TS45 Brake Sensor Corrosion

Bulletin Type: FC

Bulletin No: TS45-FC-2514

PQR No: 500000007816

Rev No:0

Ref. No:000700004635

Vehicle Model: TS45

Flat Rate Time / Code: 4 men x hours

Date of issue: 30/04/2025

Modify Before: 30/04/2026

What to do with off coming parts:

What to do with outstanding parts of previous
revision:

☒Scrap
☐Return
☐Use with additional parts
☐On consignment
☐No off coming parts

☐Scrap
☐Return
☐Use with additional parts
☐On consignment
☒No outstanding parts

Description of the modification:
To prevent corrosion caused by road
conditions (such as the salting of roads) on the
brake sensors of TS45 vehicles, a design
modification was implemented to shield the
sensors from external environmental exposure.

Bulletin Responsible: Mehmet Ali KAYSANIK

Published & Approved By: Ahmet Ozan Özcan

SERVICE BULLETIN
SAFETY INSTRUCTIONS
1. Mechanical Requested Dress Code
WARNING:
➢ Dress properly to avoid personal injury and damage to the
vehicle
Always wear protective clothing
Do not wear any worn or loose-fitting clothing
Remove jewelry before starting to work
In case of long hair, use hairnet
The illustration on the left shows some of the correct and
incorrect clothing
✓ Sharp edged items should be avoided in order not to
scratch vehicle (i.e. belts, watches, necklace)
✓
✓
✓
✓
✓

2. Protect Seats when Mechanic Starts Working

✓ Seats, trimming, upholstery stuff and carpeting should be
protected with appropriate coverings.

3. Welding on the Chassis
a. Always disconnect the batteries (starting with the negative lead).
b. Disconnect the connectors of electrical and electronic equipment (electronic control
units, sensors and actuators) if they are less than 2 meters away from the chassis
part to be welded or the earth terminal of the welding equipment.
c. The earth terminal should never be attached to vehicle components such as engine,
axles and springs. Arcing on these parts is not permitted, because of the risk of
damage to bearings, springs, etc.
d. The earth terminal must make good contact and be placed as close as possible to
the part to be welded.
e. Plastic pipes, rubber parts and parabolic springs should be well protected against
welding spatter and temperatures higher than 70°.
f. The contact switch must not be in the accessory or contact position. The contact key
should be removed.
g. Reconnect in reversed order of disconnecting. Ensure that a good earth connection
is made between chassis, engine and cab.

SERVICE BULLETIN
CANCELED PART LIST PER VEHICLE
No canceled parts.
INCLUDED PART LIST PER VEHICLE
NO

PRODUCT NO

PRODUCT NAME

1

9325-8289

2

IMAGE

QTY

UNIT

Plate, Brake Sensor

1

PIECE

9325-8290

Plate, Brake Sensor

1

PIECE

3

-

CRC SP400 Corrosion Inhibitor

1

PIECE

4

TM212144

Grommet Ø55

1

PIECE

5

MS810086

Grommet, Blind(35)

1

PIECE

6

SM-36Y

Band

0,6

METER

7

MP453093Y

Oval Head Screw

8

PIECE

-

NOTE: If the part has not been published in the system, record your usages and invoice it to Temsa.

SERVICE BULLETIN

Figure 1 – Application of Sealing Compound
Sealing should be applied to close gaps caused by bends after the material has been produced.

Figure 2 – Application of Sealing Compound
After the sealing compound porcess, product should be paint, color specified in the technical drawing.

SERVICE BULLETIN

Figure 3 – Required Points of Sealing Application
Sealing must be applied to the areas indicated in the above visual before the part is painted.

SERVICE BULLETIN
,

Figure 4- Application of Grommet

Figure 5- Application of Grommet to Cable and Hose Holes
Grommet must be applied to the holes indicated in the visual above, and foam edge tape must be applied to the
specified surfaces.

SERVICE BULLETIN

Figure 6 – Assembled View of the Part on the Vehicle

Figure 7- Assembled View of the Part on the Vehicle

SERVICE BULLETIN

Figure 8 - Assembled View of the Part on the Vehicle

Figure 9 - Assembled View of the Part on the Vehicle

SERVICE BULLETIN

Figure 10 - Assembled View of the Part on the Vehicle
After part number 9325-8289 is mounted onto the vehicle, CRC SP400 Corrosion Inhibitor must be applied
to the brake sensors. Following this application, part number 9325-8290 must be mounted and secured
using 8 screws.

SERVICE BULLETIN
LABOR BREAKDOWN
Application

Time

Demounting Old Systems

0 hour

Mounting New Systems

4 hours

Total Labor Time

4 hours
AFFECTED VEHICLE

No

VIN

1

NLTEJXA93R1000457

2

NLTEJXA95R1000458

3

NLTEJXB96S1000618

4

NLTEJXB94S1000620

5

NLTEJXB98S1000622

6

NLTEJXB9XS1000623

7

NLTEJXB97S1000658

8

NLTEJXB95S1000660

9

NLTEJXB99S1000659

10

NLTEJXB97S1000661