Field campaign
Topic

Software update for the rear door control modules - 00BB and 00BC during PDI (SC23
/24)

Market area

Bentley: worldwide (2WBE),China 796 VW Import Comp. Ltd (Vico), Beijing (6796)

Brand

Bentley

Transaction No.

2071260/43

Campaign
number

EC89

Note
Type
US code

Vehicle data
New Continental GT and New Continental GTC
Sales types

Type MY

Brand Designation Engine code Gearbox code Final drive code

3S3* 2022 E

*

*

*

3S3* 2023 E

*

*

*

3S3* 2024 E

*

*

*

3S4* 2022 E

*

*

*

3S4* 2023 E

*

*

*

3S4* 2024 E

*

*

*

Chassis numbers

Manufacturer Filler Type Filler MY Factory From

To

SCB

DT4 ZG

8

R

C

000312 000312

SCB

CW1 3S

2

R

C

000112 000112

SCB

*

*

R

C

012190 013506

SCB

DX3 3S

1

R

C

007100 007100

SCB

*

*

*

P

C

004980 012138

SCB

*

*

*

N

C

096643 098461

SCB

*

*

*

R

C

013892 019088

*

Prod from Prod to

Documents
Document name
master.xml
sc2324vinlistv42_181124.pdf

Transaction No.: 2071260

EC89

/43

Software update for the rear door control modules - 00BB and 00BC during PDI
(SC23/24)

Notes

Release date: Aug 21,
2025

Repair instructions

Technical background
CAUTION
Please refer to all of the instructions within the Work section. The instructions MUST be followed in the
exact order as detailed

Revision history 2071260/33
The glass setting will now be done post software update.
Warning added to ensure glass measurements MUST be attached to the DISS.
Note: The instructions must be conducted to completion until further notice

Remedy
All instructions within the Work section must be conducted as detailed
Software update is available for the left and right hand rear door control modules - Diagnostic address 00BB
Driver side and 00BC Passenger side
The software eliminates the rear window short drop function

Customer notification
Please ensure the instructions are conducted during the PDI process

Warranty
Warranty type

790

Damage service number EC89
Damage code

00 66

Criterion ID 01
Time to conduct the Software Version Management (SVM) update - Rear door control modules
Labour operation code
Time

01 51 00 00
As per ODIS log Must not exceed 30 TU

Time to conduct initial measurement checks Profile (Y-Axis) and Interlock (X-Axis)
Labour operation code

64 38 02 00

Time

30 TU
CAUTION

The labour codes below MUST only be claimed if the Profile (Y-Axis) and Interlock (X-Axis) were out of
specification (before and / or after the software update was conducted)
Time to conduct the front glass adjustment procedure
Labour operation code

64 40 15 00

Time

140 TU (per side)

Time to conduct the rear glass adjustment procedure
Labour operation code

64 75 15 00

Time

170 TU (per side)

Water leak test
Labour operation code

64 38 01 99 (Use this code when conducting the water leak test)

Time

20 TU

Parts
Not applicable

Parts supply
Not applicable

Parts despatch control
Not applicable

Repair instructions

Notes

Technical background
CAUTION
Please refer to all of the instructions within the Work section. The instructions MUST be followed in the
exact order as detailed

Revision history 2071260/33
The glass setting will now be done post software update.
Warning added to ensure glass measurements MUST be attached to the DISS.
Note: The instructions must be conducted to completion until further notice

Check

If the vehicle is not already listed as repaired in “Repair history" (in Elsa pro), check for the presence of the
blue paint completion mark as shown within the Identification section
If neither are evident please conduct the instructions within the Work section to completion

Parts
Not applicable

Work
Note: DO NOT CONDUCT ANY ADJUSTMENTS UNTIL INSTRUCTED

Section 1 - Software update to the rear door control modules 00BB and 00BC - Short drop function
elimination

The following software update eliminates the rear window short drop function
•

The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable
battery charger to the vehicle. For further information refer to the Repair manual

• During the
update
switch off all
unnecessary
consumers
(ventilation,
seat heater,
interior
illumination
etc) ensure
the main
light switch
is set to ‘off’
and leave
the driver’s
door open

• Because of the
highest
transmission
stability you
MUST use the
diagnosis
interface VAS
6154 (WiFi
diagnostic tool)

ONLY in USB
operation or
the cableconnected
VAS 5055 for
the
reprogramming
(updating) of
control units. If
these units are
not available,
the diagnosis
interface VAS
5054 (A) can
also be used in
USB mode

• Do Not under
any
circumstances
use a
Bluetooth
connection to
conduct the
reprogramming
(updating) of
any control
units
2) Referring to Figure 1 - Within the Special functions tab - Select SVM - Code Input (Point A)
• Select Perform test (Point B)

Figure 1

3) Referring to Figure 2 - Enter the SVM code 370WAD01

Figure 2
4) When prompted enter your global user ID and password
- Follow all on screen prompts to continue through the procedure, the identification data will be transferred
5) The control modules will automatically be updated one by one, starting with 00BB (Driver rear) and then
00BC (passenger rear)
6) On completion check the door control module versions against the Reference tables 3 and 4 (depending
on Part number/Software version)

Reference table 3

Door
control
module

Part number

00BB Rear
driver’s
door

4M1959955D 0189

V03935413CW

00BC 4M1959955D 0189
Rear
passenger
door

V03935413CX

Software Target data
version
container

Reference table 4

Door
control
module

Part number Software Target data
version
container

00BB Rear
driver’s
door

4M1959955J 0430

V03935405MS

00BC 4M1959955J 0430
Rear
passenger
door

V03935405MT

7) Switch off the ignition
•

Remove the diagnostic interface from the OBD port

•

Switch off and remove the battery charger from the vehicle

•

Close the bonnet, boot and all doors

•

Lock the vehicle

•

Wait 5 minutes to allow the vehicle to go into bus silence

•

When 5 minutes has elapsed, unlock the vehicle and open the driver’s door

•

Switch on the ignition

8) VERY IMPORTANT - Referring to Rep.Gr 64 - Side glass - To initialise
9) Once the software update has been conducted continue with the remaining instructions
Hint: The remaining instructions MUST be conducted regardless if adjustments were conducted or not
10) Referring to Rep.Gr 64 - Measure and record the points as detailed below on the left and right hand side
Profile (Y-Axis) and Interlock (X-Axis)
CAUTION
All measurements must be recorded and saved as they will be required to be attached to a non technical
DISS query at the end of the procedure

IMPORTANT: THE REQUIRED MEASUREMENTS MUST BE RECORDED PRIOR TO MAKING ANY
POST SOFTWARE UPDATE ADJUSTMENTS DO NOT CONDUCT ANY ADJUSTMENTS UNTIL
INSTRUCTED WITHIN THIS PROCEDURE
FAILURE TO ATTACH THE MEASUREMENTS TO THE DISS WILL RESULT IN NON PAYMENT OF THE
WARRANTY CLAIM.

Left hand side
•

Profile (Y-Axis)

•

Interlock (X-Axis)

Profile (Y-Axis)

Vehicle position

Tolerance Actual Measurement +/- (Post
software update)

50mm from top of
division bar

Front drop door glass to +0mm/rear quarter glass
2mm

50mm from
bottom of division
bar

Front drop door glass to +0mm/rear quarter glass
2mm

Interlock (X-Axis) Vehicle position

Tolerance

50mm from top
of the window

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

50mm from the
waistrail seal

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

Actual Measurement +/(Post software update)

Right hand side
•

Profile (Y-Axis)

•

Interlock (X-Axis)

Profile (Y-Axis)

Vehicle position

Tolerance Actual Measurement +/- (Post
software update)

50mm from top of
division bar

Front drop door glass to +0mm/rear quarter glass
2mm

50mm from
bottom of division
bar

Front drop door glass to +0mm/rear quarter glass
2mm

Interlock (X-Axis) Vehicle position

Tolerance

50mm from top
of the window

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

50mm from the
waistrail seal

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm