Technical Service Bulletin
Transaction No.: 2077876/1
91-25-03 - Park Distance Control (PDC) / Maneuver braking does not work and message in the instrument cluster
-KX2-

Condition
Applicable Vehicles
Models

Year

Eng. Code

Trans Code

VIN Range From VIN Range To

Atlas

2024-2025

All

All

All

All

Atlas Cross Sport

2024-2025

All

All

All

All

GTI

2022-2024

All

All

All

All

Golf R

2022-2024

All

All

All

All

Revision Table
Instance Number

Publish Date

Version Number

2077876/1

5/9/2025

91-25-03

Reason for Updating
Original Publication.

Customer Concern:
After the engine start the parking aid/maneuver braking does not work. Additionally, the message” Fault parking aid, Maneuver braking or fault
Rear Traffic Alert” is shown in the instrument cluster.
After switching the ignition off and on the functions are restored and a message is also no longer shown.
Work Shop Findings:
The customer statement cannot (always) be reproduced.
There are no relevant entries logged in the parking aid control unit (diagnostic address 0076).
There is no reference to a faulty parking assist sensors.
There is no recognizable external damage to the parking assist sensors.

NOTICE
If software updates or flash campaign/actions are performed on a vehicle, a charger with at least 70A charging current
MUST be used in order to avoid problems during software updates and flash campaign/actions.

Technical Background
Incorrect software in parking aid control unit (diagnosis address 0076).
NOTICE
Only parking aid control units with software version 0577 and 0578 are affected by this complaint.

Production Solution
Not applicable.

Service
Critical Warning:
The Midtronics battery charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of
charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in
damage to the control module. Control modules damaged by inadequate voltage will not be covered under the warranty policy.The technician
should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the duration of the update.
The procedure may cancel itself if the hazard warning lights are not switched ON. The hazard warning lights prevent the system from switching
to bus sleep mode during the update.

ODIS-Service tester should be updated to the latest GFF technical version 23.2.2 or higher and SW version 2.49.8 or higher.
WARNING
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may result if
contact is made with spinning fan blades.
– Keep hands and all objects away from Radiator Fan(s) during Update Process!

NOTICE
Prior to launching the ODIS Service diagnostic applications and starting control module update process, confirm tester
screen saver and power settings in accordance with Diagnostic Device Hardware & Windows® - VHW-20-02 Change Power
Options After Windows®10 Upgrade. Failure to do so may result in the tester entering power save mode during data
transfer, and subsequent control module failure. When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 6154
wireless transmitter head for a flash procedure, connect a USB cable between the transmitter head and the tester. Failure
to do so may lead to errors during the flash procedure. VAS tools must only be used with their power adapters plugged in.
Under no circumstances should they be used on battery power alone during the programming procedure.

To Update-Programming using Software Version Management (SVM), review and follow instructions in Technical Bulletin
Instance 2014603 “Software Version Management”.
The SVM process must be completed in its entirety so the database receives the update confirmation response. A warranty
claim may not be reimbursed if there is no confirmation response to support the claim or action is carried out that is not
explicitly stated in the Technical Bulletin.

•

Update the software of the parking aid control unit (diagnostic address 0076 ) according to the table below.

Model

Engine

Old Software Part
No.

Old Software
Version

New Software Part
No.

New Software
Version (or
higher)

SVM Unit
Code

Atlas/Cross Sport

All

5WA.919.294.C

0577

5WA.919.294.C

0581

4E8B

Atlas/Cross Sport

All

5WA.919.298.B

0578

5WA.919.298.B

0582

4E8B

GTI / Golf R

All

5WA.919.294.C

0577

5WA.919.294.C

0581

4E8B

GTI / Golf R

All

5WA.919.298.B

0578

5WA.919.298.B

0582

4E8B

The procedure can be found in GFF under Functions/ Component Selection, Software Version Management, Adapting
Software.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin
Instance 2014603.

Warranty
Active VW Customer Mobility Program (VWCMP) loaner vehicles are eligible to receive $35 per day for loaner expense reimbursement under
warranty (refer to document VWS-14-03 for applicable labor operation).

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual

1)

Model(s)

Year(s)

Eng. Code(s)

Trans.
Code(s)

VIN Range From

VIN Range To

Atlas

2024-25

All

All

All

All

Atlas Cross Sport

2024-25

All

All

All

All

GTI

2022-24

All

All

All

All

Golf R

2022-24

All

All

All

All

SAGA Coding
Claim Type:

Use applicable Claim Type

1)

Service Number:

Damage
Code

HST

Damage Location (Depends on
Service No.)

9174

0039

__

Use applicable when indicated
in Elsa (L/R)

Parts Manufacturer

Atlas, Atlas Cross Sport, GTI, Golf R

WWO 2)

MY 2025 Atlas, Atlas Cross Sport

VOA 2)

Labor Operation 3 ) : GFF/Guided functions (including Battery charge)

01500010= See Elsa for latest time units

Labor Operation 3 ) : Update Programming Driver Assistance Control
Module

GFF time with a max of 50TUs

Diagnostic Time

4)

GFF Time expenditure

01500060 = Actual GFF print out with max 50TUs

YES

Road Test

01210004 = see Elsa for latest time units

YES

Technical Diagnosis

01320000 = 00 TU max.

NO

Claim Comment: Input “As per Technical Bulletin 2077876” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only.

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

Required Parts and Tools
No Special Parts are required.

Tool Description

Tool No.

Modtronics Battery Tester/Charger

MTRMSP0702 Battery Maintainer/Charger

VAS Diagnostic Tool

VAS 6150/X & VAS 6160/X and ODIS Service with current online
updates.

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and
Repair Manuals for the latest information.
© 2025 Volkswagen Group of America, Inc. All rights reserved. The information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America,
Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may
be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher