SERVICE BULLETIN
Subject: TS35 Mux Units Pin Changing and
Diode Checking Bulletin

Bulletin Type: Service Campaign Recall

Bulletin No: TS35-SR-2501

PQR No: 500000007839

Rev No:00

Ref. No: 700004731

Vehicle Model: TS35

Flat Rate Time / Code: 100 min

Date of issue: 09.05.2025

Modify Before: 09.05.2026

What to do with off coming parts:

What to do with outstanding parts of previous
revision:

☒Scrap
☐Return
☐Use with additional parts
☐On consignment
☐No off coming parts

☐Scrap
☒Return
☐Use with additional parts
☐On consignment
☐No outstanding parts

Description of the modification:
This bulletin aims to check and solve Mux
06A033,06A035 and 06A037 issues.

Bulletin Responsible: Bahadır Kaya, İbrahim Oğuz

Published & Approved By: Cemre Kılınç

SERVICE BULLETIN
SAFETY INSTRUCTIONS
1. Mechanical Requested Dress Code
WARNING:
 Dress properly to avoid personal injury and damage to the
vehicle
Always wear protective clothing
Do not wear any worn or loose-fitting clothing
Remove jewelry before starting to work
In case of long hair, use hairnet
The illustration on the left shows some of the correct and
incorrect clothing
 Sharp edged items should be avoided in order not to
scratch vehicle (i.e. belts, watches, necklace)






2. Protect Seats when Mechanic Starts Working
 Seats, trimming, upholstery stuff and carpeting should be
protected with appropriate coverings.

3. Welding on the Chassis
a. Always disconnect the batteries (starting with the negative lead).
b. Disconnect the connectors of electrical and electronic equipment (electronic control
units, sensors and actuators) if they are less than 2 meters away from the chassis
part to be welded or the earth terminal of the welding equipment.
c. The earth terminal should never be attached to vehicle components such as engine,
axles and springs. Arcing on these parts is not permitted, because of the risk of
damage to bearings, springs, etc.
d. The earth terminal must make good contact and be placed as close as possible to
the part to be welded.
e. Plastic pipes, rubber parts and parabolic springs should be well protected against
welding spatter and temperatures higher than 70°.
f. The contact switch must not be in the accessory or contact position. The contact key
should be removed.
g. Reconnect in reversed order of disconnecting. Ensure that a good earth connection
is made between chassis, engine and cab.

SERVICE BULLETIN
1-) Open the front relay panel. Locate the MUX5-B 1.1 .

SERVICE BULLETIN
2-) Check the pin B16 on the Mux 1.1 B socket. If there is no diode on this pin, you should add the diode that is in
the part list as “Figure-1”.
If there is a diode, then check the diode polarity and make sure that this is good and working properly. If this diode
is damaged, replace it.

Figure-1-

SERVICE BULLETIN
3-) Step 1: Check the diode on the “TBS VALVE DIODE” Socket. If there is no diode on this pin, you should add the
diode that is in the part list, as “Figure 2 ”.
If there is a diode, then check the diode polarity and make sure that this is good and working properly. If this diode
is damaged, replace it.
Step 2: If there is a cable connected to Mux 1.1 C03 numbered as”13-560”, remove it. Blind and insulate the
removed cable with electrical tape.
Step 3: Remove the 14-109 cable on the front relay panel from Mux1.1 B15 Pin and connect it to Mux 1.1 C03 Pin
as shown in “Figure 2”.

Figure -2-

SERVICE BULLETIN
4-) Locate the MUX5-B 2.1

SERVICE BULLETIN
5-) Check the pin C21 on the Mux 2.1 C socket. If there is no diode on this pin, you should add the diode that is in
the part list, as “Figure 3 ”.
If there is a diode, then check the diode polarity and make sure that this is good and working properly. If this diode
is damaged, replace it.

Figure-3-

SERVICE BULLETIN
INCLUDING PART LIST
PART NUMBER
9460-549

PART DESCRIPTION
CONN-MALE-2 WAYS-SEALED

9402-81Y

QTY
3

6
T-FEM-0,75-1,5 mm2

96200-6301-02Y

SEAL

9431-22Y

6
3

DIODE, 10A10(10A)

9460-554

3
CONN-FEMALE-2 WAYSSEALED

9402-190Y

6
T-MALE-1,5 – 2,5 mm2

96210-6200-02Y

SEAL

6

SYMBOL

SERVICE BULLETIN
The program Links
ZR5 :
** TS04-LC3-000 software should be installed on vehicles with software starting with

TS02-LC3-…

https://content.temsa.com/sapcs?get&pVersion=0045&contRep=ZADNSPEKTEP07101&docId=0050568F7
25E1FE087DCF91ED61D04BC&accessMode=r&compId=TS04-LC3-000.zip
** TS05-LC3-000 software should be installed on vehicles with software starting with

TS03-LC3-…

https://content.temsa.com/sapcs?get&pVersion=0045&contRep=ZADNSPEKTEP07101&docId=0050568F7
25E1FE087DCF0494DCAC4BC&accessMode=r&compId=TS05-LC3-000.zip
Multiviu :

**TS02-MV-009 software should be installed on vehicles with software starting with

TS02-MV-…

https://content.temsa.com/sapcs?get&pVersion=0045&contRep=ZADNSPEKTEP07101&docId=0050568F72
5E1EEFBFE8994B08D484B9&accessMode=r&compId=TS02_MV_009.L2P.zip
**If the vehicle has TS00-MV3-000 or later, you don’t need to update Multiviu.
Important Note:
-The software mentioned above are up to date software. If there is previously published bullettin for these
vehicles, please refer to this bullettin and install these software.
-Before downloading the ZR5 software; you have to check, which program variant is installed on the
vehicle. If “TS02-LC3-…” is installed then you should download “TS04-LC3-000”.
If “TS03-LC3-…” is installed then you should download “TS05-LC3-000”
-To download ZR5 Kibes software, your computer must have Logicad3.014.2
-To be online for option page on ZR5 software, you can connect 1000Kbaud rate
-Please note option selections before installing ZR5 software. If the options are reset, after installing,
reselect the same options.

SERVICE BULLETIN
Uploading the up to date program(ZR5):
1- Park the vehicle to an area which is proper to work and remove the cover.

2- To install the ZR5 software, locate the KIBES socket next to the OBD socket by looking at the label on
the cover.

SERVICE BULLETIN
3- Connect one end of the KIBES cable to the CANanalyzer or Peak cable and the other end to the KIBES
diagnostic socket. Connect the CANanalyzer or Peak output to the computer. Make sure that the KIBES
dongle is inserted to your computer.

SERVICE BULLETIN

SERVICE BULLETIN
4- Install the ZR5 software on the vehicle as described in the images. Turn the ignition switch on. Do not
start the engine.

SERVICE BULLETIN

Hint: The software version must be selected correctly. The number shown in the picture may be
representative.

SERVICE BULLETIN

SERVICE BULLETIN
- Click "Preferences" to check the Baudrate and port. (for TS Coachs it is updated from
250k to 1000k)

SERVICE BULLETIN
4.2- Click on the instructions shown in order in the picture.
1.click here
2.click
here
3.click
here

4.3- If you get an error when you start loading of software, try CV flash download.

SERVICE BULLETIN

2.Then click here. Start arrow will be
green If the selected port is true.

1.click
here

SERVICE BULLETIN
Uploading the up to date program (Multiviu):
1-Park the vehicle to an area which is proper to work.
2-Connect your computer to the vehicle by using the CANalyzer interface. Plug the USB part into your
computer and connect your CAN cable to the 9 pinned OBD port with the D pin low and the C pin high.

D
C

SERVICE BULLETIN
3- Turn the ignition switch on. Do not start the engine.
4- Make sure that the KIBES dongle is inserted to your computer.

Select the “Open Project” selection and click “next”.

SERVICE BULLETIN

SERVICE BULLETIN

Make sure that
right program is
choosen.

SERVICE BULLETIN
6-Right click on Mulviu then click “Communication Settings” check the Port and Baudrate.

You can change port
here. Please make
sure correct port.

You can change
“Start Baudrate”
here

You can change
“Download
Baudrate” here

SERVICE BULLETIN
7-Then Right click on Mulviu, Download the logic side of the program.

SERVICE BULLETIN
8-Right click on Mulviu again then click “Archive Download”

SERVICE BULLETIN

9- You should find program in your workspace then double click the program.

SERVICE BULLETIN

SERVICE BULLETIN
10- Click on “MRT” then click “Open”.

Make sure you choose the right program here!

SERVICE BULLETIN
11- After the software is checked, click the “Build New Archive”, then click the “Archive Download”.

12-When a warning occurs, click OK, then wait for the program to be downloaded. Do not cut the
power off during the download process, this could cause the body controller to dysfunction.
LABOR BREAKDOWN
Application

Time

Moving Mux 1.1 B15 pin to Mux 1.1 C17, checking or adding Flyback diode

10’

Checking or adding Flyback diode for Mux 1.1 B16

10’

Checking or adding Flyback diode for Mux 2.1 C21

30’

Installing ZR5 Kibes Program

5’

Installing Multiviu Program

5’

Archive Installing of Multiviu

40’

Total Labor Time

100’

SERVICE BULLETIN
No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.