NHTSA ID Number: 11018129
Manufacturer Communication Number: L74X-A.11.25
TSB/Document Date: 2025-05-07
Summary
Service campaign agreed with CARB. Problem: Lateral and longitudinal acceleration sensors need to be monitored by the OBD system. Solution: Introduction of diagnosis for lateral and longitudinal acceleration sensors.
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
34. Insert the name
“FL_47B907051_0014__V001”
FL_47B907051_0014__V001
VI.
SVM update and configuration
IMPORTANT:
Improper use of this function can cause damage
to the ECUs.
36. To start the procedure to execute an SVM
code, select the “Special functions” tab in
O.D.I.S. Service.
35. Select the extension of the file “.pdx”.
37. Click on “SVM– Code input (APSBL)” and
then on “Perform test”.
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU 0011 SW version
is 0014.
38. Enter the code "L74XA1125" in the appropriate
space at the top right and click “Adopt”.
L74XA1125
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini
S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
10/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
39. The SVM code entered is again displayed in
the dialog box. If the entered code is correct,
click on “Yes”. Otherwise click on “No” to cancel the SVM procedure.
42. If the following error screen is displayed, the
error does not indicate an issue, please press
“Continue” and continue with the campaign.
43. It might become necessary to perform one or
more of the following operations in the SVM
procedure:
40.Wait for data to be acquired from all the control units. This operation requires a few
minutes.
•
Coding;
•
Parameterization;
•
Calibration;
•
SW Update;
44. To perform these actions, it is usually necessary to click on “Finished/Next” where requested and to follow the instructions directly
provided on the O.D.I.S. Service dialog
screens.
45. After the update, leave the car in sleep for 5
minutes, key off, all doors closed and locked,
OBD disconnected.
41. The SVM function will automatically continue
with identification of the control units in the
vehicle.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
11/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Please, execute the following steps:
IMPORTANT:
Trouble shooting for SVM ERP Error received:
From the "Test plan" menu, click on the "Select
own test" box and then click on the magnifying
glass:
•
•
•
8013 → please contact Technical Support
8088 → please contact Technical Support
8101 → please check the correct syntax of
SVM code inserted.
• 8113 → This error could have several resolutions:
a. If appear only the screen with error 8113, please
perform a 12V battery reset and a sleep cycle. Repeat SVM code and contact Technical Support if
not resolved.
b. If appear the following screens (ECU02 update
failed):
Enter in the search bar “Update programming”.
Select the function “Update programming (Beta
Version)” and click on “Go to”.
Please, follow the instructions displayed: switch
the ignition OFF and back ON after 10 seconds
and then click “Done/Continue” to continue.
c. If appear the following screen at the end of the
function (ECU02 update failed):
Rev.00
CONFIDENTIAL
Click on “Attach to test plan”.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
12/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
If the steps are successful, the function Update
programming (Beta Version)" will appear in the
Test plan. Click now on the Update programming
(Beta Version)” function and then “Perform test”.
Select the control unit type to flash. In this select
option “- 1. -“, “ASAM/UDS”.
Click on “- 1. -” if the selection is correct, oth-erwise click “- 2. -” for repeat program or “- 3. -” for
abort program.
Insert the name
“FL_47B927256_0010_4821C523_V001_S”.
FL_47B927256_0010_4821C523_V001_S
Select the extension of the file “.pdx”.
Specify the control unit Diagnostic Address and
then click on “Apply” box. In this case insert “02”.
02
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU02 SW version is
0010.
After the update, perform the guided function
“SVM – Code input” again (steps from 36 to 45).
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
13/19
To:
Object:
Date:
Pages
L74XA.11.25
•
•
•
•
•
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
8118 → please perform a sleep cycle. Be
sure the control unit 5F has been updated
to correct software (see previous steps).
Check the software level via 5f – control
unit identification and compare it to the
reference table. Repeat SVM code and
contact Technical Support if not resolved.
8037 → Please check your O.D.I.S Service
version and hotfix as indicated in “Preliminary operation” section.
9999 → for the owners of the new D3 Edge
Box, please refer to the informative bulletin BI.08.24 to check the correct O.D.I.S
Service connection setup.
ECU 0011 - Status 12 → the error does not
indicate an issue and can be continue with
the next step of the campaign. Please, select option 1 to go ahead.
ECU 0017 - Status 13 → the error does not
indicate an issue and can be continue with
the next step of the campaign. Please, select option 1 to go ahead
Rev.00
CONFIDENTIAL
•
•
ODS5003E → If the following screen appear please close and repeat the SVMCode.
IMPORTANT:
Trouble shooting for DTCs after SVM code:
If during the SVM Code input procedure, the follow errors appear:
•
ECU0074 → C10C500: Basic setting (deflected) not performed: please, from the
ECU 0074, execute the guided function
“74 - Ride hide full process”
Then click on basic setting "2 - Lifting system " and
follow the instructions directly from the O.D.I.S.
Service.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
14/19
To:
Object:
Date:
Pages
L74XA.11.25
•
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
ECU00C5 → U020600: Lost Communication with folding top control module
From the "Test plan" menu. Click on the "Select
own test" box and then click on the magnifying
glass:
Click on “Attach to test plan”.
If the steps are successful, the function Update
programming (Beta Version)" will appear in the
Test plan. Click now on the Update programming
(Beta Version)” function and then “Perform test”.
Enter in the search bar “Update programming”.
Select the function “Update programming (Beta
Version)” and click on “Go to”.
Select the control unit type to flash. In this select
option “- 1. -“, “ASAM/UDS”.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
15/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Specify the control unit Diagnostic Address and
then click on “Apply” box. In this case insert “C5”.
Select the extension of the file “.odx”.
C5
Click on “- 1. -” if the selection is correct, oth-erwise click “- 2. -” for repeat program or “- 3. -” for
abort program.
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU 00C5 SW version
is 0503.
Insert the name
“FL_47B965429D_0503__V001_S”.
FL_47B965429D_0503__V001_S
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
16/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Final operations:
/* Diagnosis protocol saving */
VII.
49. Save the Diagnostic protocol as described in
the chapter “Saving a diagnostic protocol” on
app “O.D.I.S. Self Service Guide”, available on
Lamborghini HUB portal when the procedure
described in this document is completed.
Erase fault memory
46. Select the “Special Functions” card and then
“Erase fault memory - overall system” to delete all stored faults.
50.For the correct saving of the data after the SW
update, it is necessary to close O.D.I.S. Service, start a new diagnostic session and save
a new protocol. Both protocols must be attached to the Corresponding Warranty Request in LIASS.
47. The complete guide for deleting faults is available in the chapter “Reading/cleaning event
memory” on app “O.D.I.S. Self Service Guide”,
available on Lamborghini HUB portal.
IMPORTANT:
The Diagnostic Protocol must be attached to the
Corresponding Warranty Request in LIASS (to enter the request on the web portal, refer to the
W.Claim manual which you can consult in the
Warranty section of the portal).
48. Go back to the “Block diagram” card and select “Read all fault memories” from one of the
vehicle’s control units to update the display of
the faults present after deletion.
IMPORTANT:
Solve any faults still present by performing the
functions listed in the “Test plan”. Perform the
procedure “VII. Erase fault memory” again until all
faults are fully removed from the vehicle’s control
units.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
17/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Trouble shooting for generic issues:
If the following error screen is displayed,
abort the guided function by clicking on
“Cancel Test” and contact Technical Support.
If the following connection error is displayed like in the following example
screenshots:
-
If an error is displayed that regards the
hardware interface, and the "connection to
vehicle" and "key state" icons appear as
shown in the figure below:
-
Click “Cancel”;
Repeat installation of the interface
VAS6154/6154A/6154B for the instructions
in procedure (*) “Checking the VAS 6154”,
selecting the right-hand “Extras” menu in
O.D.I.S. Service and clicking on the “Diagnostic interface” button.
Rev.00
CONFIDENTIAL
It is not possible to connect to the central server; check that your laptop is correctly connected to the Internet and retry by clicking on “Yes” or “Done/continue”, as appropriate.
If the connection is dropped during the target/actual comparison during the SVM
procedure:
-
It is not possible to connect to the central server; check that your laptop is correctly connected to the Internet and retry by clicking on “1”.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
18/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
If the same error type should reoccur during the application test, try the following
procedure:
-
Exit O.D.I.S. Service
Restart O.D.I.S. Service ensuring that:
1. You have a network connection
2. The O.D.I.S. Service connection is
set to Internet
-
Run the connection test again and perform the SVM again.
IMPORTANT:
If the following error should occur, it is necessary
to follow the instructions given in BI.25.18
(Rev.02), which can be downloaded on the Lamborghini HUB portal:
IMPORTANT:
The documents which must be provided together
with the operation under warranty request are:
-
Produced Repair Order
-
Saved Diagnostic Protocol with BETA
report
Failure to follow these procedures could lead to
the request being rejected.
For more information, please contact your Area
Manager or open a ticket to Technical Support in
Lamborghini KEY (Request – General Information
– After Sales Services - After Sales Technical
Support).
Regards,
Lamborghini Service
All O.D.I.S. Service technical documentation can
be viewed on the Lamborghini web portal, in the
O.D.I.S. Sel Service app.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
19/19
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: L74X-A.11.25
Replacement Service Bulletin Number:
MFR Communication Date: 2025-04-04
MFR Internal Campaign ID/Software Version:
Communication Type: Service Campaign
NHTSA Components: POWER TRAIN
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used escaner automotriz device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way, and we’ll provide a solution within 24 hours. THINKSCAN 689BT Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- [Good News] THINKSCAN 689BT is the most competitive automotive scan tool to date, offering wireless updates with no subscription fees(valued 500Buc.ks) . With all the features of THINKTOOL PD8,PRO, built on Android 10 platform with 4-core CPU, 4GB RAM
and 64GB ROM, serving up to 5X faster than older MAX/MINI/PLUS vehicle scanners escaner automotriz, no more slow and delayed feedbacks, it's time to update your garage tool. - [Big Money Saver] Premium THINKSCAN 689BT Wireless Diagnostic Scanner Escaner Automotriz, save up to 400USD per year, includes all useful features: Full bi-directional controls, ECU coding, 34+ services, OEM all system diagnostics, Worldwide vehicles coverage, CAN FD & DoIP, FCA AutoAuth（The 689BT only provides a login and purchase portal, and users are required to register for an FCA account and pay a membership fee in order to perform the relevant automotive diagnostics)
- [3000+ Active Tests]Active testing is one of the most useful features in automotive maintenance and greatly improves mechanic efficiency. THINKCAR 689BT bidirectional scanner can send action commends to vehicle sub-systems or components for active test without using vehicle controls. It can perform various tests such as: EVAP Test, Fuel Trim Reset, Injector Buzz Test, Window/ Mirror/ Door Lock Test, Pump and Value Tests, etc. Get functions from "Diagnose>Car Model>System>Active Test".
- [Hot Advanced Features] 689BT bidirectional tool newly adds ECU Coding, Power Balance, Flash Hidden Functions, Reset Adaptive Data, Match Replaced Components, Customize OE-Settings. Such as: 1. changing the color of interior lights 2. switching on/off the auto hold, 3. customizing dash kits 4. activating the auto side mirror folding function 5. disables auto start-stop. Note: Coding functions vary by model&year.
- 【Warm Tips】Wired THINKSCAN 689 is connected through a detachable OBDII cable, and we also have added OBD2 Extension Cable (about 60 cm/2 feet) as g ift, enabling customers handling vehicle repairs with ease. Just click "Bundles Item" above to get it. Note: FCA AutoAuth is a third-party service, additional cost may be required.
- 【Professional Car Diagnostic Tool】Tired of renew fees? Thinkscan 689 scanner provides dealer-level advanced functions without annual fees for auto mechanics and repair shops. 34+ Services, 3000+ Active Test, ECU Coding, 140+ Brands Coverage, FCA AutoAuth, CANFD&DOIP Protocol, Component Matching, Power Balance, V.A.G Guided, Compatible with Google Chrome integration, etc. With strong hardware backing, 64G Memory, Android 10, 4-core processors, and 4150mAh battery. Thinkscan 689 brings you the best as your daily business helper and never lets you drop the ball!
- 【Over 34 Reset Service, Adaptation + Relearn + Calibration + Initialization + Matching】Made for workshops, Thinkscan 689 scanner provides 34+ services for worldwide vehicles: such as Gear/SAS/EPB/TPMS/D.P.F/I.M.M.O/BMS/ETS/Oil/Brake/AFS/GEARBOX/SUNROOF/SUS Reset, ABS Bleed, Injector coding, etc. Warm tips: Compatibility may vary on vehicles' model and year, please contact seller before purchase to make sure it works well on your cars.
- 【Real Active Test】Thinkscan 689 scan tool features over 3000+ full bi-directional control ability, to send commands to vehicle’s systems/components, to verify system input/output without using the vehicle's controls, e.g. turn on the radiator fan, modulate the throttle, open/close windows, operate mirrors, Injector Buz Test, turn on interior&exterior lights, sound horn, test door lock actuators, turn on/off front/rear side ACM Solenoid, Vehicle level position calibration, Wheel Speed Sensor Supply.
- 【Comprehensive Solutions with Advanced Features】Take your vehicle customization to the next level with the Thinkscan 689's advanced ECU coding capabilities. This scan tool provides power balance, PMI, unlock more new features and enhance performance by activating dormant functions, customizing OE settings, matching replaced components, and reprogramming adaptive data to elevate your driving experience. Note: Compatibility varies by car models, please check before order.
- 【Cost-effective OBD2 scanner】 Thinkcar Thinkdiag2 is the most powerful wireless diagnostic tool for it's price! Equipped with multi-functions of Newly added CAN-FD protocol, BiDirectional control(Active Test), 15 Maintenance resets, All Systems diagnosis, Auto VIN, FCA AutoAuth, Unlock the protected FCA vehicle SGW module on Chrysler, Dodge, Jeep, Alfa Romeo, and Fiat vehicles manufactured after 2019.120+ Car brands coverage, No IP limited, etc. Good for workshops & DIYers. Kindly send us VIN to check compatibility before purchase
- 【OE-Level Full Systems Car Scanner with Added CAN FD Protocol】 Upgrade of Thinkdiag, Thinkdiag2 is a bluetooth diagnostic tool can diagnose Full System such as ECM, ABS, SRS, TCM, EPB, TPMS, SAS, A/C, BMS, etc. Thinkdiag2 can read/clear fault codes, read real-time data, read control module information,etc. As the only diagnostic scanner in this price range that supports the CAN-FD protocol, it suits for the latest GM(2019-) , saving $100 to buy a CAN FD adapter, reducing the risk of undetected errors to enhancing the user experience
- 【Bidirectional Test】This bidirectional scan tool Thinkdiag2 allows you to send commands from your smartphone directly to the vehicle's ECU for active testing, quickly locate problem areas, such as A/C clutch, windows, doors, sunroof, etc., reducing the diagnostic time and money. (Note: kindly send us VIN to check compatibility before order.)
- 【15+ Maintenance Functions】Thinkdiag2 OBDII code scanner is designed for individual car owners, DIYers, and small repair shops, which has a separate menu of 15 common special functions, such as Oil reset, EPB reset, SAS calibration, ABS bleeding, injector code, TPMS reset, etc. Enter from the all-system diagnostic menu to unlock more system special functions, and effectively handle the reset and relearn of most cars. Note: The Maintenance functions that each car can do may be different
- 【120+ car brands & FCA Autoauth+10 languages】Thinkcar thinkdiag2 helps you to troubleshoot the problems fast for 100 + US, European, Asian vehicle brands after 1996 that use the OBDII protocol. Only support 12V cars, including gasoline cars and diesel cars. Supporting Autoauth allows you to unlock the protected FCA vehicle SGW module on Chrysler, Dodge, Jeep, Alfa Romeo, Fiat vehicles, etc. (Note: Only provide AutoAuth login portal, and need purchase the registration number on the AutoAuth website by yourself.) Multilingual function allows workshop mechanics to avoid language barriers and use it around the world Without restriction
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.