3

Snap-fit

A

Area “A”

B

Area “B”

© 2025 Toyota Motor Sales, USA

B

T-SB-0088-24

Rev1

October 3, 2024

Page 6 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

1. Install the mounting bracket to the lower
radiator grille using the two short
self-tapping screws.

Figure 3.

4
1

NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the
self-tapping screws.

3
2

1

1

2. Install the two long self-tapping screws
through the holes on the front license plate,
bracket, and lower radiator grille.
2

1

Short Self-tapping Screws

2

Long Self-tapping Screws

3

Front License Plate

4

License Plate Bracket

© 2025 Toyota Motor Sales, USA

T-SB-0088-24

Rev1

October 3, 2024

Page 7 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation

1. Remove the front and rear emergency
towing eyelets from the front and rear
bumpers by turning them counterclockwise.

Figure 4.

HINT
If it is difficult to loosen the emergency towing
eyelet(s), use a steel bar.

1

2

2. Place one of the removed emergency towing
eyelets into the luggage tray in the
luggage compartment.

1

Front Emergency Towing Eyelet

2

Rear Emergency Towing Eyelet

Figure 5.

HINT
Dispose of the other removed emergency
towing eyelet.

1

1

© 2025 Toyota Motor Sales, USA

Emergency Towing Eyelet

T-SB-0088-24

Rev1

October 3, 2024

Page 8 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation (continued)

3. Install the front and rear emergency towing
eyelet hole covers, which are stored in the
glove box, onto the front and rear bumpers.

Figure 6.

A. Insert the arrow-shaped part of the front
emergency towing eyelet hole cover “A”
into the eyelet hole “B” as shown. Seat
tabs to secure the hole cover to the
front bumper.

B
A

1

B. Insert the arrow-shaped part of the rear
emergency towing eyelet hole cover “A”
into the eyelet hole “B” as shown. Seat
tabs to secure the hole cover to the
rear bumper.

B

NOTE

2

Make sure the front emergency towing
eyelet cover is installed in the front, and
the rear emergency towing eyelet cover is
installed in the rear.

A

1

Front Emergency Towing Eyelet Hole Cover

2

Rear Emergency Towing Eyelet Hole Cover

A

Arrow-shaped Part

B

Eyelet Hole

© 2025 Toyota Motor Sales, USA

T-SB-0088-24

Rev1

October 3, 2024

Page 9 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Spring Spacer Removal

Spring spacers are installed on the front coil springs to prevent the front bumper from being
damaged during transit. Remove the front coil spring spacers during PDS.
Figure 7.

1

2

1

Front Suspension

2

Front Coil Spring Spacer

3

3

Coil Spring Spacer Notice Label

1. Refer to the applicable Repair Manual to lift the vehicle and extend the front suspension.
•

2025 GR Corolla:
General – Introduction – Repair Instruction – Vehicle Lift and Support Locations

2. Remove the coil spring spacers from the front coil springs.
3. Remove the coil spring notice label from the front windshield glass.

© 2025 Toyota Motor Sales, USA

T-SB-0088-24

Rev1

October 3, 2024

Page 10 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure.
•

2025 GR Corolla:
Suspension – Tire Pressure Monitoring –
Tire Pressure Warning System (for Gasoline Model (for Type B)) – Initialization
NOTE
• To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using GTS+ and select the compensation tire pressure checkbox.
Compensation pressures will display on the Health Check results screen. Adjust the tire pressure when
the tires are cold.
• The spare tire does NOT have a TPWS sensor.

Head Unit System Reset

Prior to vehicle delivery, confirm that the welcome screen with language options appears on the
head unit display when ignition is switched to the ON position. There may be instances where
the welcome screen with language options may not properly appear on the head unit display.
If the welcome screen showing language options is not displayed, complete the following steps:
1. Select the Settings option (gear icon).
2. Scroll down and select the Info & Security option.
3. The System Reset dialogue box will appear. Select Reset to confirm the resetting of
the system.
4. Confirm that the welcome screen with language options is now displayed.

Customize ACC Function

The pre-startup function detects when a user enters the vehicle and energizes the audio head
unit (+BA) so that the multimedia system can quickly be used. This function is not enabled at the
factory to reduce parasitic current draw in transit and storage. To enable this function, it is
necessary to set the ACC customization function in the navigation display to OFF.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Enter the following menus: Settings – Vehicle Customization – Utility – ACC Customize.
3. Change the setting to OFF.

© 2025 Toyota Motor Sales, USA

T-SB-0088-24

Rev1

October 3, 2024

Page 11 of 11

2025 GR Corolla Pre-Delivery Service (PDS)
Dealer Contact Information for Call Dealer Head Unit Function

Refer to the Multimedia System Owner’s Manual to add dealer contact information.
•

2025 GR Corolla:
Section 2-9 Vehicle Settings – Setting Dealer Information

Navigation — Set Date & Time by GPS

Prior to vehicle delivery, it is necessary to turn the Set Date & Time by GPS setting to the
ON position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – General – Date & Time –
Set date & time by GPS.
3. Ensure the Set Date & Time by GPS function is set to the ON position.

© 2025 Toyota Motor Sales, USA