y DIGITAL WIRELESS SYSTEM
CiPPERT °
Oi WITH LCD REMOTE is
ELECTRONICS
Fig. 1- Part #206436 Fig. 2-8 Function Receiver Part #217609
5 + ot 8 = ira =
Cal Mo Oe a
Y ZA eS 2 \Bea
(a) ono a
= 5 i
s 5
=)
a
e Bs?
Syncing transmitter (Fig. 1) to the receiver (Fig. 2)
1. Must have 12V DC to receiver.
2. Remote must be powered by battery.
3. Push and hold black button (Fig. 2A) on the receiver.
4. While black button on the transmitter is depressed, push and release LIGHT button (Fig. 1A) on remote.
NOTE: If close enough to brain, an audible “click” can be heard verifying brain is programmed to remote.
5. Release black button.
6. If asecond remote needs to be programmed to brain, repeat steps 2 through 5 with the second
remote.
NOTE: Only 2 transmitters may be programmed to a receiver at a time.
iat: RN Fig. 3B
= Ss Olay ab ——s _y om
ues ies US caaee#ekrkf*ttk
ee eee ee at ap | ae ae ae ise
Maiti imino Pa oe de eee
7 ee wa Oe. i. 1.1.3:
PEEP Fo out PEE PEPE EES
Programming transmitter to terminals on the receiver
Programming the remote to the specific terminals offers flexibility in the installation process allowing for more and
easier wiring route options. Fig. 3A shows the POWER (+) and GROUND (-) terminals 5-7 on the left side of the brain
in Fig. 2. Fig. 3B shows the POWER (+) and GROUND (-) terminals 1-4.
Rev: 01.28.25 Page 1 CCD-0001951

7 DIGITAL WIRELESS SYSTEM =
> . oy
QUiPPEeRT WITH LCD REMOTE z
ELECTRONICS
Programming transmitter to terminals on the receiver (con't)
it a Fig. 5 (c)
de :
(a= ee ) G) s FG Aladin tt
Cp cores: i I |
i =a = 4
= ofi=
1. Begin the PROGRAM process by pressing the POWER button (Fig. 4A).
2. Press and hold both UP (Fig. 5A) and DOWN (Fig. 5B) arrow keys while pressing SEL (Fig. 5C) 4 times.
ad () tod tm)
= SS eee — SSS
] AV tS & = Las Li | | Ka 7 a ee
= ELECT FUNCT 1 Ip ca FU | \s ‘y |
Liv a Bly Pens E Ss eee |
~ Gy pe: (a) =
3. To select the specific function for each terminal, press the UP (Fig. 5A) and DOWN (Fig. B) arrow keys to
scroll through all the options.
4. _ Fig. 6 shows the opening screen to the select options. FUNCT 1 determines the function for TERMINAL
1 on the receiver. By continuing to press the UP arrow key (Fig. 7A) and the DOWN arrow key (Fig. 7 B)
the function options can be scrolled through to set the description for each terminal.
5. Press the SEL button (Fig. 8A) to assign the function desired for each terminal. When the SEL button is
pressed, the remote's LCD screen will switch to the next function to be assigned (Fig. 8).
NOTE: Anytime the program mode is entered, all preset functions will be cleared and all functions will
need to be programmed.
Fig.9 Fig. 10 Fig. 11
Wan a A Se So An +* = &-
EE — : — —_ :
6. Whenall functions, 1-7 are completed, the remote will ask if there is an Alarm (Fig. 9), and then a TV Lift
(Fig. 10). Answer these questions by pressing the appropriate arrow key for YES or NO.
7. The remote will then ask to “CYCLE POWER TO COMPLETE CONFIG” (Fig. 11). Press the POWER button
to shut the remote off. Press the POWER button to turn remote back on.
Rev: 01.28.25 Page 2 CCD-0001951

DIGITAL WIRELESS SYSTEM
. °o
aipPerT WITH LCD REMOTE Ms
ELECTRONICS
8. Follow steps #1 and #2 on page 2.
9. Press the SEL button (Fig. 12), to scroll through the assigned functions to confirm accuracy.
10. [fall functions are correct, the remote is ready for operation.
Fig. 12
| AR)
a |
Operating instructions for wireless transmitter
1. Begin the PROGRAM process by pressing POWER button (Fig. 4A; pg. 2).
2. Press UP arrow (Fig. 5A; pg. 2) and SEL button (Fig. 5C; pg. 2) at the same time.
3. Press the SEL button (Fig. 12) to scroll through functions for operation.
Fig. 13 (a) Fig. 14 at a ed @)
ae ee SY ee oe oe:
yay = aoe
4. When desired function is displayed, follow on screen instructions for operation.
5. The UP arrow (Fig. 14A) will EXTEND a slideout or awning and the DOWN arrow (Fig. 14B) will RETRACT
a slideout or awning. The UP arrow (Fig. 14A) will RAISE the coach and the DOWN arrow (Fig. 148) will
lower the coach.
6. When all desired functions are completed, press the POWER button (Fig. 15A) to turn remote off. If the
remote is not turned off manually, it will automatically shut down after two minutes.
Rev: 01.28.25 Page 3 CCD-0001951

DIGITAL WIRELESS SYSTEM
QUiPPERT WITH LCD REMOTE z
ELECTRONICS
5 Function Wireless Remote Wiring Diagram
!
a
Ne3—§il
Ih
oe 28
hE a
| i af
cg: E 3 5
f 4
& i
rH
il .
a :
Rev: 01.28.25 Page 4 CCD-0001951

DIGITAL WIRELESS SYSTEM bs
my
., . r—)
Ourrerr WITH LCD REMOTE z
ELECTRONICS
8 Function Wireless Remote Wiring Diagram
3
QO fs
#
ri
Siresvuse
HEL ez c bp =
z=
aw aw w « « a « z
F(=) o ) o a oa o ao 3
5 5 6 5 5 5 5 u
= = = = = = =
As a supplier of a broad array of highly-engineered components in the recreation and transportation product markets, safety, education and customer satisfaction are
our primary concerns. Should you have any questions, please do not hesitate to contact us at 432-LIPPERT (432-547-7378) or by email at [email protected].
Self-help tips, technical documents, product videos and a training class schedule are available at lippert.com or by downloading the LippertNOW app.
Rev: 01.28.25 Page 5 CCD-0001951