Field campaign
Topic
Market area
Brand
Transaction No.
Campaign number
Note
Type
US code

Software update for the rear door control modules - 00BB and 00BC during PDI (SC23/24)
Bentley: worldwide (2WBE)
Bentley
2071260/35
EC89

Vehicle data
New Continental GT and New Continental GTC
Sales types
Type
3S3*
3S3*
3S3*
3S4*
3S4*
3S4*

MY
2022
2023
2024
2022
2023
2024

Brand Designation Engine code Gearbox code Final drive code
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*

Chassis numbers
Manufacturer
SCB
SCB
SCB
SCB
SCB
SCB
SCB

Filler
*
*
*
*
DX3
CW1
DT4

Type
*
*
*
*
3S
3S
ZG

Documents
Document name
master.xml
sc2324vinlistv35_270824.pdf

Filler
*
*
*
*
1
2
8

MY
N
P
R
R
R
R
R

Factory
C
C
C
C
C
C
C

From
096643
004980
012190
013892
007100
000112
000312

To
Prod from Prod to
098461
012138
013506
018679
007100
000112
000312

EC89

Notes

Repair instructions

Technical background
CAUTION

Revision history 2071260/33
The glass setting will now be done post software update.
Warning added to ensure glass measurements MUST be attached to the DISS.
Note: The instructions must be conducted to completion until further notice

Remedy
All instructions within the Work section must be conducted as detailed
Software update is available for the left and right hand rear door control modules - Diagnostic address 00BB Driver side and 00BC Passenger
side
The software eliminates the rear window short drop function

Customer notification
Please ensure the instructions are conducted during the PDI process

Warranty accounting instructions
Warranty type
790
Damage service number EC89
Damage code 00 66
Criterion ID 01
Time to conduct the Software Version Management (SVM) update - Rear door control modules
Labour operation code 01 51 00 00
Time
As per ODIS log Must not exceed 30 TU
Time to conduct initial measurement checks Profile (Y-Axis) and Interlock (X-Axis)
Labour operation code
64 38 02 00
Time
30 TU
CAUTION

Time to conduct the front glass adjustment procedure
Labour operation code
64 40 15 00
Time
140 TU (per side)
Time to conduct the rear glass adjustment procedure
Labour operation code
64 75 15 00
Time
170 TU (per side)
Water leak test
Labour operation code
64 38 01 99 (Use this code when conducting the water leak test)
Time
20 TU

Genuine parts
Not applicable

Parts supply
Not applicable

Parts despatch control
Not applicable

Repair instructions

Notes

Technical background
CAUTION

Revision history 2071260/33
The glass setting will now be done post software update.
Warning added to ensure glass measurements MUST be attached to the DISS.
Note: The instructions must be conducted to completion until further notice

Check
If the vehicle is not already listed as repaired in “Repair history" (in Elsa pro), check for the presence of the blue paint completion mark as shown
within the Identification section
If neither are evident please conduct the instructions within the Work section to completion

Genuine parts
Not applicable

Work
Note: DO NOT CONDUCT ANY ADJUSTMENTS UNTIL INSTRUCTED

Section 1 - Software update to the rear door control modules 00BB and 00BC - Short drop function elimination
The following software update eliminates the rear window short drop function
•

The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable battery charger
to the vehicle. For further information refer to the Repair manual

•

During the update switch off all unnecessary consumers (ventilation, seat heater, interior illumination etc) ensure the
main light switch is set to ‘off’ and leave the driver’s door open

•

Because of the highest transmission stability you MUST use the diagnosis interface VAS 6154 (WiFi diagnostic tool)
ONLY in USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these
units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode

•

Do Not under any circumstances use a Bluetooth connection to conduct the reprogramming (updating) of any control
units

2) Referring to Figure 1 - Within the Special functions tab - Select SVM - Code Input (Point A)
• Select Perform test (Point B)

Figure 1
3) Referring to Figure 2 - Enter the SVM code 370WAD01

Figure 2
4) When prompted enter your global user ID and password
- Follow all on screen prompts to continue through the procedure, the identification data will be transferred
5) The control modules will automatically be updated one by one, starting with 00BB (Driver rear) and then 00BC (passenger rear)
6) On completion check the door control module versions against the Reference tables 3 and 4 (depending on Part number/Software version)

Reference table 3

Door control module

Part number Software version Target data container

00BB - Rear driver’s door

4M1959955D 0189

V03935413CW

00BC - Rear passenger door

4M1959955D 0189

V03935413CX

Reference table 4
Door control module

Part number Software version Target data container

00BB - Rear driver’s door

4M1959955J 0430

V03935405MS

00BC - Rear passenger door

4M1959955J 0430

V03935405MT

7) Switch off the ignition
•

Remove the diagnostic interface from the OBD port

•

Switch off and remove the battery charger from the vehicle

•

Close the bonnet, boot and all doors

•

Lock the vehicle

•

Wait 5 minutes to allow the vehicle to go into bus silence

•

When 5 minutes has elapsed, unlock the vehicle and open the driver’s door

•

Switch on the ignition

8) VERY IMPORTANT - Referring to Rep.Gr 64 - Side glass - To initialise
9) Once the software update has been conducted continue with the remaining instructions
Hint: The remaining instructions MUST be conducted regardless if adjustments were conducted or not
10) Referring to Rep.Gr 64 - Measure and record the points as detailed below on the left and right hand side Profile (Y-Axis) and Interlock (XAxis)
CAUTION

IMPORTANT: THE REQUIRED MEASUREMENTS MUST BE RECORDED PRIOR TO MAKING ANY POST SOFTWARE UPDATE
ADJUSTMENTS DO NOT CONDUCT ANY ADJUSTMENTS UNTIL INSTRUCTED WITHIN THIS PROCEDURE
FAILURE TO ATTACH THE MEASUREMENTS TO THE DISS WILL RESULT IN NON PAYMENT OF THE WARRANTY CLAIM.

Left hand side
• Profile (Y-Axis)
•

Interlock (X-Axis)

Profile (Y-Axis)

Vehicle position

Tolerance Actual Measurement +/(Post software update)

50mm from top of Front drop door glass
division bar
to rear quarter glass

+0mm/2mm

50mm from bottom Front drop door glass
of division bar
to rear quarter glass

+0mm/2mm

Interlock (XAxis)

Vehicle position

Tolerance Actual Measurement +/(Post software update)

50mm from top
of the window

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

50mm from the
waistrail seal

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

Right hand side
• Profile (Y-Axis)
•

Interlock (X-Axis)

Profile (Y-Axis)

Vehicle position

Tolerance Actual Measurement +/(Post software update)

50mm from top of Front drop door glass
division bar
to rear quarter glass

+0mm/2mm

50mm from bottom Front drop door glass
of division bar
to rear quarter glass

+0mm/2mm

Interlock (XAxis)

Vehicle position

Tolerance Actual Measurement +/(Post software update)

50mm from top
of the window

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

50mm from the
waistrail seal

Rear door quarter glass
strip to front door drop
glass edge

11mm +/1mm

NOTICE

Or
Should one or both of the measurements not be within specification the operative must refer to Rep.Gr 64 - Rear door drop
glass - To adjust and conduct the front and rear glass adjustment procedure for the affected side left and / or right hand side
to completion (all steps)
Note: Once the adjustment has been conducted please go to step 11 and follow all remaining steps until completion
11) VERY IMPORTANT - Referring to Rep.Gr 64 - Side glass - To initialise
CAUTION

Hint: Ensure all windows, sunroof and convertible roof (where applicable) are fully closed before conducting the water leak check
12) Conduct a water leak check to ensure that water is not leaking into the vehicles interior - Water leaks must be resolved before handing over
the vehicle to the customer
13) Conduct the PDI road test to check for any wind noise related issues
14) Raise a non technical DISS query titled SC23/24 X and Y Axis measurement feedback ensuring the following Is attached
•

Online ODIS log

•

Feedback regarding all of the steps which were conducted including all measurements before and after the software update was
conducted

15) Referring to the Identification section - Apply a blue paint completion mark on the engine partition brace (Figure 3)

Identification
Blue paint completion mark on the engine partition brace

Figure 3

INTERNAL

#

SCBCF13S4NC096643
SCBDF33S8NC096919
SCBDF33S8NC098461
SCBDK33S4PC004980
SCBDK33SXPC005003
SCBCT23S7PC005379
SCBCT23S8PC005522
SCBDK33S6PC005743
SCBCX13S0PC006601
SCBC113S5PC006983
SCBC113S0PC007118
SCBDW33S2PC007333
SCBCG2ZG5PC007428
SCBCX13S9PC007617
SCBDK33S6PC007637
SCBCX13S8PC007706
SCBCG13SXPC007772
SCBCG13S6PC007798
SCBCG23S2PC007836
SCBCG13S7PC007924
SCBCX13S1PC007949
SCBDK33S6PC008075
SCBCK13SXPC008290
SCBCV13S7PC008352
SCBCK13S6PC008397
SCBCT23S7PC008444
SCBCX13S3PC008519
SCBCG13S3PC008536
SCBCX13S0PC008591
SCBCG13S4PC008660
SCBCG13S9PC008671
SCBCG13S4PC008738
SCBCX13S5PC008747
SCBCG13S4PC008786
SCBCG13S2PC008835
SCBCG13S3PC008911
SCBCG13S1PC009040
SCBCG13S8PC009066
SCBCV13S1PC009139
SCBDX33SXPC009201
SCBDX33S8PC009231
SCBCX13S1PC009264
SCBC113S7PC009299
SCBDG4ZG9PC009330
SCBC113S7PC009383
SCBCK13S4PC009418
SCBDU33SXPC009465
SCBCX13S8PC009519
SCBDT43S5PC009530
SCBCV1ZG4PC009588
SCBCT2ZG5PC009613
SCBCG13S8PC009620
SCBCG13S4PC009629
SCBCG13SXPC009702
SCBCG13S7PC009723
SCBCT2ZGXPC009736
SCBCG13S4PC009761
SCBCG13S2PC009810
SCBCG13S0PC009837
SCBDX33S9PC009853
SCBCW13S8PC009880
SCBCG13S9PC009884

SCBDX33S9PC009903
SCBCG13S5PC009929
SCBCV13S7PC009937
SCBCG13S3PC009945
SCBCG13S9PC009951
SCBDX33S0PC009952
SCBCK13S6PC009954
SCBCG13S1PC009958
SCBCG13S3PC009962
SCBCK13S4PC009984
SCBCK13S8PC009986