Installation and Conversion Instructions

911 (992)
09/23

ENU

0913

0

911 GT3 Touring Manthey Performance Kit

Vehicle Type:

911 GT3 Touring

Model Year:

As of 2021

Information:

Retrofitting
The Manthey Performance Kit for the 911 GT3 RS (type 992) was developed in close collaboration
between the Porsche Development Center in Weissach and Manthey Racing GmbH.
The Tequipment range is targeted to motor sports enthusiasts and amateur motor sports drivers.

Note:

The Manthey Performance Kit for the 911 GT3 RS (type 992) was developed in close collaboration
between the Porsche Development Center in Weissach and Manthey Racing GmbH.
The Tequipment range is targeted to motor sports enthusiasts and amateur motor sports drivers.

NOTICE
•

The individual components of the 911 GT3 Touring Manthey Performance Kit are in perfect harmony. For
this reason, they must only be installed together on the vehicle. Individual offers are shown separately.

Parts Info:

992.044.855.06

911 GT3 Touring (type 992) Manthey performance kit
For vehicles with a front axle lift system (order no. 2UH)
911 GT3 Touring (type 992) Manthey performance kit
For vehicles without a front axle lift system (order no. 2UH)
911 GT3 Touring (type 992) Manthey aerodynamics kit

992.044.855.07
992.044.855.12
Parts to be ordered separately:
PAF.108.749

8x

 Hexagon flange bolt, M8 x 42, for upper axle guide

N 102.723.02

2x

 Hexagon collar nut, M10, for connecting rod

N 107.847.02

2x

 Hexagon flange bolt, M12 x 1.5 x 85, for lower axle guide

PAF.003.923

12 x

 Hexagon nut, M8, for upper strut bearing

9A7.007.755.00

2x

 Cheese head bolt securing seat belt to seat

9A7.007.483.00

4x

 Outside hexagon round-head bolt, M10 x 28, to seat rail

PAF.910.423

2x

PAF.100.829

3x

 Inside hexagon round/pan-head screw, M6 x 16, for rear
diffusor
 Hexagon-head bolt, M6 x 16, for rear diffusor

PAF.104.513

2x

PAF.912.572

6x

 Cheese head bolt with internal multiple-tooth head, M12 x 1.5 x
55
 Hexagon flange bolt M8 x 22

Tequipment

Aug 20, 2024
Page 1 of 21

0

911 (992)
0913

ENU

Installation and Conversion Instructions

09/23

PAF.908.088

2x

 Hexagon flange bolt, M12 x 1.5

000.043.305.38

1x

Adhesive

Suspension alignment: Intermediate plates may be required for adjusting the camber values
on the front axle. Order the required intermediate plates accordingly:
9F1.401.443.H

2x

 Intermediate plate, 2.0 mm

NOTICE
Vehicle and driver weight
•

Before starting the alignment, please ensure the following conditions are met:



Fuel tank is completely full



Driver’s weight (incl. helmet and racing suit) has been determined or requested and is placed on the
driver’s seat with an equivalent weight

Information
Please pass all this information on to the customer.
In addition, provide the customer with the Race Circuit brochure included with the scope of parts.

Information

Content:

•

Some of the repair illustrations show only one side of the vehicle or a similar component.

•

Naturally, some steps also have to be performed on the opposite side of the vehicle as well.

•
•
•
•
•
•
•
•
•
•
•
•

1. Preparatory work
2. Installing the door entry guards
3. Installing the door projectors
4. Chassis assembly
5. Installing brake lines
6. Installing front spoiler
7. Installing the air control elements on the underbody
8. Installing rear diffusor
9. Affixing stickers
10. Concluding work
11. Performing suspension alignment of the vehicle
12. Only for race track use: Installing towing loops

Information
Check that the decorative film is aligned correctly. The alignment cannot be corrected afterwards.

Aug 20, 2024
Page 2 of 21

Tequipment

Installation and Conversion Instructions

911 (992)
09/23

ENU

0913

0

Information
The decorative films must also be ordered in the desired color.
These are available from 01/2023.
Assembly:

1

Preparatory work
1.1

2

Connect battery charger.  Workshop Manual '2X00IN Battery trickle charge'

Installing the door entry guards
Set
1

– Door entry guards (left and right) 992.044.856.17
– Door entry guard

2.1

Remove  1 -1- door entry guard. 
Workshop Manual '680719 Removing and
installing cover moulding'

2.2

Install illuminated door entry guard  1 -1-.
 Installation and Conversion Instructions
'680700 Door-sill guards, illuminated ADY /
ATX'

3

1

Installing the door projectors
Set

– Door projectors (left and right) 992.044.856.16

3.1

Remove door guard light.  Workshop
Manual '961619 Remove and install door
guard light'

3.2

Remove door panel.  Workshop Manual
'705919 Removing and installing front door
panel'

3.3

Install new door projector  3 -1-.
Ensure correct installation position and
engagement.

3.4

Connect electric plug connection  3 -3-.
The electric plug connection must engage perceptibly.

Tequipment

2

Aug 20, 2024
Page 3 of 21

0

911 (992)
0913

ENU

Installation and Conversion Instructions

09/23

3.5

Install the door panel  3 -2-.  Workshop
Manual '705919 Removing and installing
front door panel'
1
2
3

– Door projector
– Door panel
– Electric plug connection

3
WARNING
Preloaded or pressurized components
•

Risk of squashing or bruising



Do not reach into the danger area.



Relieve tension on components before starting work.



Secure components to prevent them from loosening suddenly.
4

Chassis assembly
Leave all four wheels removed as described in the Chassis section.

4
Kit with front axle lift – 4 dampers / springs / strut bearings including PASM deactivation kit 992.044.856.10

Aug 20, 2024
Page 4 of 21

Tequipment

Installation and Conversion Instructions

911 (992)
09/23

ENU

0913

0

Kit without front axle lift – 4 dampers / springs / strut bearings including PASM deactivation kit 992.044.856.13
1
– Front-axle spring strut without front axle lift - 992.044.856.14 (LH) /
992.044.856.34 (RH)
2
– Front-axle spring strut with front axle lift - 992.044.856.11 (LH) / 992.044.856.31 (RH)
3
– Rear-axle spring strut - 992.044.856.12 (LH) / 992.044.856.32 (RH)
4
– Tie-rod end - 992.044.856.30
5
– PASM deactivation it
4.1

Remove all four wheels.  Workshop Manual '440519 Removing and installing wheel with
central bolt'

4.2

Replace original tie-rod ends with tie-rod ends  4 -4-.  Workshop Manual '488119
Remove and install tie-rod end'
There is no need to replace the tie-rod ends if the chassis package without aerodynamic components is installed. Brake cooling spoiler cannot be removed. Do not
align suspension yet. Do not install wheels yet.

4.3

Removing front spring strut.  Workshop Manual '408519 Removing and installing front
spring strut'

4.4

Disassembling front spring strut
4.4.1

Disassembling spring strut.  Workshop Manual '408537 Disassembling and
assembling front spring strut'

4.4.2

Remove front axle lift
Only for vehicles with front axle lift system.
The tool for the lock nut supplied with the kit must be used!

4.4.3

Remove height-adjusting nut  5 -2- and lock nut  5 -3-.
Use a P90026 - P90026 - hook spanner for this purpose.

4.4.4

Screw the front axle lift  5 -4- up until the dust boot detaches  5 -1- and
remove dust boot  5 -1-.

4.4.5

Remove front axle lift  5 -4- and
lock nut  5 -5- from the spring
strut  5 -6- (use open-ended
spanner 700 17 171 and
open-ended spanner 700 17 184).
1
2
3
4
5
6

–
–
–
–
–
–

Dust boot
Height-adjusting nut
Lock nut
Front axle lift system
Lock nut
Spring strut
5

Tequipment

Aug 20, 2024
Page 5 of 21

0

911 (992)
0913

ENU

Installation and Conversion Instructions

09/23

4.5

Assembling new front spring strut with front axle lift
4.5.1

Mount lock nut  6 -17- and lift system  6 -16- on the spring strut  6 -12-.
Do not tighten to the specified torque yet.

4.5.2

Install plastic cap  6 -15- on the shock absorber housing (use impact sleeve 700
17 169 and a plastic hammer).

4.5.3

Push spring plate  6 -9-, coil spring  6 -8-, intermediate ring  6 -7- and
helper spring  6 -6- onto the piston rod.
Then mount the bellows  4.5.4.
Install rubber stop  6 -3- and supporting mount  6 -2- on the piston rod and
tighten nut  6 -1- (use special tool KW 685 10 179).
Ensure that the rubber stops  6 -3- are installed correctly: Pointed tapered end
must be facing upwards as shown  6. Tightening torque 40 Nm

1
2
3
4
4.1
4.2
5
6
7
8
9
12
15
16
17
Aug 20, 2024
Page 6 of 21

–
–
–
–
–
–
–
–
–
–
–
–
–
–
–

6
Nut
Supporting mount - 65A.49.376 (LH) / 65A.49.377 (RH)
Rubber stop
Bellows
Mounting ring on bellows
Spring plate, upper
Upper ring on bellows
Auxiliary spring
Intermediate ring
Coil spring
Lower spring plate (install with a distance of 10 mm from the lift system)
Spring strut
Plastic cap
Lift system (carried over from standard chassis)
Lock nut

Tequipment

Installation and Conversion Instructions
4.5.4

911 (992)
09/23

ENU

0913