PAF007960

 O-ring 3.00 x 3.00
– Heat exchanger

3 pieces

1

Required material if the oil pan (oil guide housing) must be replaced (usually already available at
the Porsche Center):
Part No.

Designation
– Application point / additional designation

Quantity

00004320593

 Lubricating grease (100 g/ 3.52 oz tube), Klüberplus gel
– O-rings

As required

00004330516

 Coolant (20 l/ 5.28 gal container)
– Cooling system

As required

...

 Engine oil, C40GT standard
– EXXON MOBIL 1, 0w-40

As required

9A757390010

 Refrigerant compressor oil 1234yf
– Air-conditioning system

As required

...

 Refrigerant 1234yf
– Air-conditioning system

As required

AfterSales

Aug 20, 2024
Page 3 of 6

1

Service

Technical Information

ENU 117/24

1751

Required tools
Tools:

•

Access ramps, e.g.9453 - access ramps,

Additional tool required if the oil pan seal needs to be replaced:
•
•

•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

Aug 20, 2024
Page 4 of 6

P90999 - PIWIS Tester 4
Battery charger with a current rating of at least 90 A, e.g. VAS 5908 - 90-A battery charger. For
further information about the battery chargers to be used, see the corresponding Workshop Manual.
 Workshop Manual '270689 Charge battery and vehicle electrical system'
Torque wrench, 2-10 Nm (1.5-7.5 ftlb.), e.g., V.A.G 1783 - torque wrench, 2-10 Nm (1.5-7.5
ftlb.)
Torque wrench, 20-100 Nm (15-74 ftlb.), e.g., VAS 5820 - Torque wrench, 20-100 Nm (15-74
ftlb.)
Torque wrench, 40-200 Nm (30-148 ftlb.), e.g., V.A.G 1332A - torque wrench, 40-200 Nm
(30-148 ftlb.)
Torque wrench, 150-800 Nm (111-592 ftlb.), e.g. V.A.G 1601 - Torque wrench, 150-800 Nm
(111-592 ftlb.)
Cooling system service device, e.g., VAS 531 011 - Cooling system service device
Funnel, e.g., VAS 6675A - Funnel
Filling device, e.g., 9696 - Filling device
Vacuum pump, e.g., VAS 6096/2 - Vacuum pump
Spring band clamp pliers, e.g. VAS 6890 - Spring band clamp pliers
Oil filter release key, e.g. 9443 - oil filter release key
Strapping belts, e.g. 9454 - strapping belts
Retaining plate, e.g. 9769 - retaining plate
Support e.g. 9769/1 - support
Assembly tool, e.g., 9822 - assembly tool
Fixing pins, e.g. P90030 - centring pins
Disassembly tool, e.g. VAS 6933 - disassembly tool
Master Gear engine lift table, e.g. VAS 6832 - Master Gear engine lift table
Assembly aid, e.g. 9794 - assembly aid
Socket wrench, e.g. 9796 - socket wrench
Wheel mounting trolley, e.g. VAS 6266A - wheel mounting trolley
Transmission and gearbox jack, e.g. VAS 6931A - Transmission and gearbox jack
Suspension device, e.g. 3033 - suspension device
Fixing parts, e.g. 9590 - fastening parts
Retaining plate, e.g. 9769 - retaining plate
Support e.g. 9769/1 - support
Support e.g. 9769/2 - support
Motor adapter, e.g. 9771 - engine adapter
Pick-up set, e.g. 9771/1 - recording set
Engine holder, e.g. 9771/2 - engine holder
Transmission holder, e.g. 9932 - transmission holder
Pick-up hooks, e.g. 9971 - pick-up hook
Engine and gearbox bracket, e.g. VAS 6095 - engine bracket

AfterSales

Service

Technical Information
•
•
•
•

117/24 ENU

1751

1

Workshop crane, e.g. VAS 6100 - workshop crane
VAS 6122 - Engine plug set
Steering wheel balance, e.g., VAS 6826 - Steering wheel balance
Air conditioning service device recommended by Porsche for refrigerant R1234yf, e.g. VAS
581 007 - extraction device for R1234yf

Additional required tool if the reversing camera needs to be calibrated
•
•
•
•

Spacing laser, e.g. VAS 6350/2A - spacing laser
Locking pins, e.g. VAS 6350/7 - locking pins
Calibration device, e.g. VAS 6350A - calibration device
Wheel alignment adapter for wheels with center lock, e.g. VAS 6830 - wheel alignment adapter
for wheels with center lock

Additional required tool if the surround view camera needs to be calibrated
•

Calibration system, e.g. VAS 721 001 - calibration system

Locate oil leakage and replace oil pan seal and additional oil pan (oil guide housing) if necessary
Work Procedure: 1

2

Raise the vehicle.
 Workshop Manual '4X00IN Raise the vehicle'
Remove rear spoiler, lower part (diffuser).

 Workshop Manual '66591925 Remove and install rear spoiler, lower part (diffuser)'
Information
Oil leakage must be clearly identifiable and reproducible.
To do this, proceed as follows:
1. Document the original complaint condition with meaningful photos.
2. Attach documentation to PCSS line.
3. Clean the engine and transmission thoroughly.
4. Spray large areas of the engine and transmission with SpotCheck around the suspected leakage
points.
5. If necessary, test drive the vehicle with the engine oil and coolant having at least reached
operating temperature.
6. Locate the oil leakage.
7. Produce photo documentation of the leakage point located using SpotCheck.
8. Attach documentation to PCSS line.

AfterSales

Aug 20, 2024
Page 5 of 6

1

Service

Technical Information

ENU 117/24

1751
3

Check oil leakage in the area of the sealing point on the oil pan (oil guide housing) to the crankcase.
Assessment

Action
If the complaint is not rectified by this
technical information, resume troubleshooting.
Install rear spoiler, lower part (diffuser)
 Workshop Manual '66591925 Remove
and install rear spoiler, lower part (diffuser)'

Oil leakage between oil pan (oil guide
housing) and crankcase not present.

( )

and drain the vehicle.
End of action.
Oil leakage present between oil pan (oil
guide housing) and crankcase.

(✗)
4

Go to  4.

Replace existing oil pan (oil guide housing) with new oil pan (oil guide housing), including the oil
pan seal.
For procedure, see:  Workshop Manual '175019 Remove and install oil pan'

Labor position and PCSS encryption
Information
If necessary, additionally required working time guideline values for preparatory or follow-up actions need
to be determined using the Porsche Central Service System (PCSS), depending on the equipment of the
vehicle.
Labor position:
APOS

Labor operation

17500140

Check for oil loss

17501975

Remove and install oil pan

I No.

PCSS encryption:
Location (FES5)

1750

Oil pan

Damage type (SA4)

1521

crack/incipient crack

Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.

© 2024 Porsche Cars North America, Inc.

Aug 20, 2024
Page 6 of 6

AfterSales