possible). See Power Cycling the Vehicle on page 226Power Cycling the Vehicle on page 228.
To reset the instrument panel, shift into Park and press the top two buttons on the steering wheel (Voice Commands and Next)
for 15-30 seconds, or until the screen turns black. A few seconds later, a Tesla logo appears. Wait approximately 30 seconds
for the instrument panel to restart.
NOTE: Restarting the touchscreen also activates the drive mode selector on the center console.
NOTE: Pressing the scroll buttons only restarts the touchscreen. It does not restart any other vehicle component and does not
power CybertruckModel SModel X off and on.
Tilt the Touchscreen (if equipped)
To tilt the touchscreen, navigate to Controls, then touch the display icon to choose the desired position.
WARNING: When the center display is tilting, ensure that there are no objects (such as your fingers or jewelry) between
the screen and instrument panel to reduce the risk of injury or damage.
Rear Touchscreen
The rear touchscreen provides rear passengers with access to:

22

Owner's Manual

Owners Manual

1. Temperature: Touch the arrows to decrease/increase cabin temperature.
2. Power: Touch to turn the rear climate control system on or off.
3. Rear fan: Touch to turn the rear fan on or off, to adjust fan speed and control the direction of air flow from the rear vents
(see Adjusting the Front and Rear Vents on page 436).
4. Seats: Control rear seat heaters and move the front passenger seat forward/rearward using the arrows.
5. Media: Play, pause, skip or rewind through the currently playing song (see Media on page 451).
6. Video: Access video streaming services.
7. Settings: Touch to pair up to two sets of Bluetooth headphones, change the brightness or clean the display.
NOTE: Connect headphones to listen to audio from the rear touchscreen. The vehicle supports up to two Bluetooth devices
at a time (such as one phone and one headset).
NOTE: Some vehicles manufactured before approximately September 2021 may require additional hardware to be
compatible with wireless headphones. If the touchscreen displays this message, use the mobile app to schedule a service
appointment.
8. Auto: If Auto is enabled and a passenger is detected, the set temperature is maintained for the rear cabin.
NOTE: Enable Sync on the rear tab of the front touchscreen's climate controls to set both the front and back cabin
temperatures.
9. Volume: Touch to adjust the volume.

Owner's Manual

23

Owners Manual
NOTE: You can also use the front touchscreen to adjust climate settings in the rear cabin (see Adjusting Climate Control
Settings on page 427).
NOTE: Adjusting the media and volume controls also adjusts the front cabin settings.
Control the rear screen from the front

To control the rear touchscreen from the front, open the rear screen remote control app in the bottom bar on
the front touchscreen. Besides audio, video and climate controls, you can lock the rear display in the app or by
touching Controls > Display > Lock Rear Display.

Customizing Display and Sound Settings
Touch Controls > Display to adjust display settings to suit your preferences:
• Appearance: Customize the display to be Dark or Light. When set to Auto, the brightness changes automatically based on
ambient lighting conditions.
• Reduce Blue Light: When enabled, the display automatically adjusts to use warmer colors at night.
• Brightness: Drag the slider to manually control the brightness level. If Display Mode is set to Auto, the touchscreen further
adjusts based on both the ambient lighting conditions and your brightness preference. CybertruckModel SModel X
remembers your chosen brightness preference and adjusts the touchscreen accordingly.
• Energy Saving: When toggled on, CybertruckModel SModel X reduces the amount of energy being consumed when not in
use (for newer vehicles, this is automated). See Getting Maximum Range on page 480.
• Screen Clean Mode: When enabled, your touchscreen darkens and temporarily disables to facilitate cleaning. Follow the
onscreen instructions to exit Screen Clean Mode.
• Touchscreen Language: Select the language that the touchscreen displays.
NOTE: CybertruckModel SModel X must be in Park to change the language. When you change the language, you
experience a brief delay as CybertruckModel SModel X shuts down and restarts the touchscreen.
• Voice Recognition Language: Choose the language to be used for voice commands.
• Voice Navigation Language: Choose the language that the navigation system uses for spoken instructions.
NOTE: For languages that require a download, select the language in the dropdown list to initiate the download (Wi-Fi
connection required).
• Lock Rear Display: Lock access to the rear touchscreen.
• Time: Choose to display time in either 12 or 24 hour format.
• Energy Display: Choose to display remaining energy and charging units as either a percentage of battery energy remaining,
or as an estimate of the distance you can drive.When you choose Distance, you can display mileage based on either:
◦ Rated - based on EPA testing in the United States.
◦ Ideal - assumes ideal driving conditions based on driving at a steady speed of 55 mph (89 km/h) on a flat road, and
using no additional energy (seat heaters, air conditioning, etc).
NOTE: When anticipating when you need to charge, use energy estimate as a general guideline only. Many factors have an
impact on energy consumption. See Factors Affecting Energy Consumption on page 480.
• Distance: Choose to display measurements in metric (kilometers, centimeters, etc.) or imperial (miles, inches, etc.) units.
• Temperature: Choose to display temperature using Fahrenheit or Celsius.
• Tire Pressure: Choose to display tire pressures using BAR or PSI.
In addition to customizing the display, you can enable Joe Mode to reduce the volume of all chimes that are not related to
critical safety issues. Touch Controls > Safety > Joe Mode to enable.

24

Owner's Manual

Owners Manual
Naming your Vehicle
To further personalize your vehicle, you can name it. Touch Controls > Software > Name Your Vehicle located on the right side
of the touchscreen below the image of CybertruckModel SModel X. If your vehicle already has a name, touch the existing
name to change it. Enter the new name in the popup and touch Save. The name of your CybertruckModel SModel X also
appears in the Tesla mobile app.
Erasing Personal Data with a Factory Reset
When transferring ownership of CybertruckModel SModel X, perform a factory reset for security purposes before removing
your vehicle from your account by touching Controls > Service > Factory Reset. Before erasing data,
CybertruckModel SModel X verifies your credentials by prompting you to enter the user name and password associated with
your Tesla account.
NOTE: Performing a factory reset is only possible when the vehicle is in your account. After the vehicle is removed from your
account, you no longer have access to perform a reset of customized settings to the factory defaults and to erase all personal
data.

Owner's Manual

25

Owners Manual
Interior Electronics
In addition to storage compartments and cup holders (see Interior Storage on page 118), the CybertruckModel SModel X
interior supports various electronics such as USB ports, a phone dock for two phones (or other devices) or a wireless phone
charger (depending on date of manufacture)a wireless phone charger, and a 12V power socket.
USB Ports
Your CybertruckModel SModel X has two USB ports located on the front of the center console that you can use to connect
USB devices. To play audio files stored on a USB drive connected to these ports, see Playing Media from Devices on page
453. You can also use these ports to charge USB devices.

In addition, Model X has two charge-only USB ports located at the rear of the center console, and another charge-only
connection located between the third row seats (if equipped).
NOTE: Do not connect multiple devices using a USB hub. This can prevent connected devices from charging or from being
recognized by the Media Player.
NOTE: You can charge four devices simultaneously using the two ports at the front of the center console and the two at the
rear of the console.
NOTE: Power is available whenever the vehicle is considered "awake" The vehicle may be awake for many reasons. For
example, when using features such as Summon, or when features such as Preconditioning, Cabin Overheat Protection, Keep
Climate On, Dog Mode, Camp Mode, Sentry Mode, etc. are enabled. The vehicle is also awake whenever the low voltage
battery is being charged or is in use, during HV charging, when the vehicle is communicating with the mobile app, etc. Leaving
an accessory plugged in does not deplete the low voltage battery.
Low Voltage Power Socket
Your CybertruckModel SModel X has a power socket located on the front of the center console. An additional low voltage
power socket is located in the rear trunk. Power is available whenever the instrument panel and touchscreen are on.

26

Owner's Manual

Owners Manual

The low voltage power socket issockets are suitable for accessories requiring up to 11A continuous draw (15A peak) or a
maximum of 150 continuous watts (180 watts peak).
NOTE: Power is available whenever the vehicle is considered "awake" The vehicle may be awake for many reasons. For
example, when using features such as Summon, or when features such as Preconditioning, Cabin Overheat Protection, Keep
Climate On, Dog Mode, Camp Mode, Sentry Mode, etc. are enabled. The vehicle is also awake whenever the low voltage
battery is being charged or is in use, during HV charging, when the vehicle is communicating with the mobile app, etc. Leaving
an accessory plugged in does not deplete the low voltage battery.
NOTE: In situations where CybertruckModel SModel X is unable to detect the key fob (low battery, interference, etc.), place it
immediately below the low voltage power socket in the center console where CybertruckModel SModel X can best detect it.
WARNING: The power socket and an accessory’s connector can become hot.

Owner's Manual

27

Owners Manual
Interior Electronics
In addition to storage compartments and cup holders (see Interior Storage on page 115), the CybertruckModel SModel X
interior supports various electronics such as USB ports, wireless phone chargers, and a 12V power socket.
USB Ports
CybertruckModel SModel X has five USB ports:
• Two USB ports are located in the front compartment of the center console. These can be used to charge USB devices and
to play audio files from a phone or USB device (see Playing Media from Devices on page 453).
• Two USB ports are located below the rear touchscreen that can be used to charge USB devices.
• One USB port is located inside the glovebox. This port is equipped with a USB flash drive. The secure location of this USB
port makes it ideal for saving Sentry Mode and Dashcam video footage.
The USB ports can output power up to approximately 27W (which may vary depending on vehicle manufacture date).
See USB Drive Requirements for Recording Videos on page 424 for information about formatting USB flash drives.
To access the front USB ports, open the front compartment of the center console. The front USB ports are located on the rear
wall of the compartment:

Rear USB ports are located below the rear touchscreen:

28

Owner's Manual

Owners Manual

Glovebox USB port:

NOTE: Power is available when the vehicle detects that a user is present. A user is considered present when a person is in the
driver seat or interacts with the touchscreen. Power is also available whenever the low voltage battery is being charged or is in
use, when you charge the high voltage Battery, or when the vehicle is communicating with the mobile app. Leaving an
accessory plugged in does not deplete the low voltage battery.
NOTE: Use USB 3.0 compliant cables to connect a device to a USB port. Using non-compliant cables can result in slower
charging, potential connection problems or degraded performance.
NOTE: Do not connect multiple devices using a USB hub. This can prevent connected devices from charging or from being
recognized by Media Player, Sentry Mode, Dashcam, etc.
Wireless Phone Chargers
Wireless phone chargers are integrated into the front console and rear armrest, providing up to 15W of power to charge Qienabled phones. To charge your phone, place it on one of the two charge pads. The phone must be in direct contact with the
wireless charger. Your device may feel warm while charging, but this is a normal effect of inductive charging.
CAUTION: Before you charge, remove any objects (coins, keys, metal objects, etc.) between the phone and charger, as
well as any NFC cards (for example, the vehicle key card, credit cards, or hotel key) placed on or behind the phone (like
with integrated phone cases). Damage to NFC cards can occur when you charge the phone without first removing the
card.

Owner's Manual

29

Owners Manual

When placed on the wireless charger, your phone charges whenever the vehicle is powered on (the touchscreen is on and you
are in the vehicle). Your phone does not charge when you leave the vehicle unless a feature, such as Keep Climate On, Dog
Mode, Camp Mode, or Sentry Mode is enabled.
NOTE: The wireless phone charger may not work if your phone case is too thick or is made of metal. Try removing the phone
from its case before placing it on the charger.
NOTE: The wireless phone charger does not charge if the vehicle's high voltage Battery is discharged.
Low Voltage Power Socket
Your CybertruckModel SModel X has a power socket located in the center console's compartment. To access the low voltage
socket, open the front compartment of the center console.

The power socket is suitable for accessories requiring up to 12A continuous draw (16A peak).
NOTE: Power is available when the vehicle detects that a user is present. A user is considered present when a person is in the
driver seat or interacts with the touchscreen. Power is also available whenever the low voltage battery is being charged or is in
use, when you charge the high voltage Battery, or when the vehicle is communicating with the mobile app. Leaving an
accessory plugged in does not deplete the low voltage battery.
WARNING: The power socket and an accessory’s connector can become hot.
WARNING: To prevent excessive interference with the vehicle’s electronics, Tesla recommends that you do not plug any
non-Tesla accessories, including power inverters, into the low voltage power socket. However, if you do use a non-Tesla
accessory and notice any malfunctions or unexpected behavior, such as indicator lights, alert messages, or excessive
heat from the accessory, unplug the accessory from the low voltage power socket immediately.

30

Owner's Manual

Owners Manual
NOTE: A power inverter plugged into the low voltage power socket must support 16V DC input to function.
CAUTION: Do not attempt to jump start CybertruckModel SModel X using the low voltage power socket. Doing so can
result in damage.
Active Road Noise Reduction
CybertruckModel SModel X is equipped with Active Road Noise Reduction which reduces low-frequency road noise while
driving on rough surfaces. To accomplish this, the vehicle uses the seat microphones to measure noise in the cabin, then
generates anti-noise through the speakers to intelligently create quiet zones around each occupantthe front occupants
depending on vehicle and environmental factors.

To turn Active Road Noise Reduction on or off, open the Media Player and touch Audio Settings icon > Options > Active Road
Noise Reduction (the audio settings icon shows an equalizer with three vertical lines). This may require several minutes of
driving time to calibrate before enabling.
NOTE: To ensure active noise reduction operates effectively, avoid covering the microphones (with seat covers, etc.). Active
Road Noise Reduction may disable if a window is rolled down, door is open, or the fan is turned up. Active Road Noise
Reduction also disables if there is a rear passenger in the vehicle.
CAUTION: To prevent damage to these microphones when cleaning, do not over-saturate the area of the seats where the
microphones are located.

Owner's Manual

31

Owners Manual
Instrument Panel
Instrument Panel Overview
The instrument panel changes depending on whether CybertruckModel SModel X is:
• Off or Parked (shown below).
• Driving (see Instrument Panel - Driving on page 34).
• Charging (see Charging Instructions on page 465).
When CybertruckModel SModel X is off or Parked, the instrument panel shows remaining estimated range, vehicle status, and
outside temperature.

32

Owner's Manual

Owners Manual

1. When the car is off and you initially press the brake, indicator lights flash briefly along the top of the instrument panel.
Unless an indicator light applies to a current situation, it should turn off. If an indicator light fails to turn on or off, refer to
Indicator Lights on page 35.
2. An image of your car and its accompanying status (such as lights on, door open, etc.).
3. Total estimated driving distance (or energy) available. Instead of driving distance, you can display the percentage of
battery energy remaining. To do so, touch Controls > Display > Energy Display.
NOTE: When anticipating when you need to charge, use estimates as a general guideline only.
4. Estimated outside temperature.
5. Pay attention to instructions or important alert messages that display here. If any alerts are in effect, you can view
information about them by touching Controls and then touching the bell icon located at the top of the screen.
6. Currently selected drive mode: Park, Reverse, Neutral, or Drive. If Auto Shift out of Park is enabled, Drive or Reverse is
automatically selected (based on sensor input) and displayed on the instrument panel when the driver's door is closed and
seatbelt is buckled (see Seat Belts on page 143).
7. Current time of day.
See Popup Messages and Vehicle Alerts on page 21 for more information about alert popups on your vehicle's touchscreen.

Owner's Manual

33

Owners Manual
Instrument Panel - Driving
When CybertruckModel SModel X is driving (or ready to drive), the instrument panel shows your current driving status and a
real-time visualization of the road as detected by the Autopilot components. The visualization automatically zooms in and out
based on the detected road type.

NOTE: Touch Controls > Autopilot > Full Self-Driving Visualization Preview (if equipped) to display more details about the
roadway and its surroundings, such as road markings, stop lights, objects (such as trash cans and poles), etc.
1. The instrument panel displays your location on a map, a wiper menu, Auto Shift out of Park instructions, etc. When a
navigation route is active, the upcoming portion of the route displays.

34

Owner's Manual

Owners Manual
2. The speed limit (if available) that is currently being detected by Speed Assist (see Speed Assist on page 411).
NOTE: A blue outline may appear around the speed limit icon to notify that you are above the speed limit.
3. Current driving speed.
4. The currently set cruising speed. When Traffic-Aware Cruise Control is available but you haven't set a cruising speed by
engaging Traffic-Aware Cruise Control or Autosteer, the icon is gray (see Autopilot Features on page 327).
5. Autosteer is actively steering CybertruckModel SModel X. When Autosteer is available but you haven't activated it, the
icon is gray (see Autosteer on page 328).
6. When navigating, upcoming instructions in the navigation route appear here.
7. Total estimated driving distance (or energy) available. Instead of driving distance, you can display the percentage of
battery energy remaining (touch Controls > Display > Energy Display).
NOTE: When anticipating when you need to charge, use estimates as a general guideline only.
8. Surrounding road users are shown in their corresponding locations.
WARNING: Although the instrument panel shows surrounding traffic, some vehicles may not be displayed. Never rely
on the instrument panel to determine if a vehicle is present (for example, in your blind spot). Always use your mirrors
and perform shoulder checks.
9. Your CybertruckModel SModel X.
10. The power meter displays real-time power usage. During acceleration, the bar fills to the right to represent power being
used. During deceleration (when CybertruckModel SModel X is moving and you release your foot from the accelerator
pedal), the bar fills to the left with a green color to represent power being fed back to the Battery by regenerative braking
(see Regenerative Braking on page 262).
11. When Autosteer is active and detects the driving lane, it is highlighted in blue (see Autopilot Features on page 327).
Depending on the current driving scenario, you may see neighboring lanes.
NOTE: In situations where Autosteer is unable to detect lane markings, the driving lane is determined based on the vehicle
you are following.
NOTE: If Navigate on Autopilot is active, the driving lane displays as a single blue line in front of
CybertruckModel SModel X (see Navigate on Autopilot on page 331).

Indicator Lights
Indicator lights display along the top of the instrument panel to show status and alert you of specific vehicle conditions.
Indicator

Description
(USA) A brake system fault is detected or the brake fluid level is low. See Braking and Stopping on page 260.
Contact Tesla immediately.

(Canada) A brake system fault is detected or the brake fluid level is low. See Braking and Stopping on page
260. Contact Tesla immediately.

(USA) A brake booster fault has been detected. See Braking and Stopping on page 260.

Owner's Manual

35

Owners Manual
Indicator

Description
(Canada) A brake booster fault has been detected. See Braking and Stopping on page 260.

(USA) An ABS (Anti-lock Braking System) fault is detected. See Braking and Stopping on page 260. Contact
Tesla immediately.

(Canada) An ABS (Anti-lock Braking System) fault is detected. See Braking and Stopping on page 260.
Contact Tesla immediately.

(USA) A parking brake fault is detected. Contact Tesla. See Parking Brake on page 264.

(Canada) A parking brake fault is detected. Contact Tesla. See Parking Brake on page 264.

(USA) The parking brake is manually applied. See Parking Brake on page 264.

(Canada) The parking brake is manually applied. See Parking Brake on page 264.

Tire pressure warning. The pressure of a tire is out of range. If a fault with the Tire Pressure Monitoring
System (TPMS) is detected, the indicator flashes. For a TPMS fault, contact Tesla. See Tire Care and
Maintenance on page 489.

A seat belt for an occupied seat is not fastened. See Seat Belts on page 143.

Airbag safety. If this red indicator does not flash on briefly when CybertruckModel SModel X prepares to
drive, or if it remains on, contact Tesla immediately. See Airbags on page 198Airbags on page 187.

36

Owner's Manual

Owners Manual
Indicator

Description

Front fog lights are on, if equipped. See Lights on page 250.

Parking lights (side marker lights, tail lights, and license plate lights) are on. See Lights on page 250.

Low beam headlights are on.

High beam headlights are on. Illuminates when high beams are on but the Auto High Beam setting (if
equipped) is turned off or if the Auto High Beam setting is turned on but is temporarily unavailable. See Lights
on page 250.

High beam headlights are currently turned on, and Auto High Beam (if equipped) is ready to turn off the high
beams if light is detected in front of CybertruckModel SModel X. See Lights on page 250.

High beam headlights are temporarily turned off because Auto High Beam (if equipped) is on and is detecting
light in front of CybertruckModel SModel X. When light is no longer detected, the high beams automatically
turn back on. See Lights on page 250.

If a fault is detected with the Adaptive Front Lighting this indicator displays, if equipped. See #unique_105 on
page .

If a fault is detected with the Adaptive Front Lighting this indicator displays, if equipped. See Adaptive Front
Lighting System (AFS) on page 254.

This indicator flashes amber when the electronic stability control systems are actively minimizing wheel spin
by controlling brake pressure and motor power. See Traction Control on page 290. If this indicator remains
on, a fault is detected and you should immediately contact Tesla.

If a fault is detected that reduces the performance of the air suspension system, this amber indicator light
displays (see Air Suspension on page 266). If the problem persists, contact Tesla.

Owner's Manual

37

Owners Manual
Indicator

Description

If a fault is detected that disables the air suspension system, this red indicator light displays (see Air
Suspension on page 266). Contact Tesla.

Vehicle Hold is actively applying the brakes. See Vehicle Hold on page 287.

Electronic stability control systems are no longer minimizing wheel spin. See Traction Control on page 290.

CybertruckModel SModel X is in Transport mode and can roll freely. It does not automatically shift into Park
when you exit. See Activate Transport Mode on page 581.

Trailer mode (if equipped) is active. See Towing and Accessories on page 311.

A blue snowflake appears when some of the energy stored in the Battery may not be available due to cold
weather conditions. During these cold weather conditions, charging rates may also be limited. If
CybertruckModel SModel X is plugged in, you can heat your Battery by turning on climate control with the
mobile app. The snowflake disappears when the Battery is sufficiently warm.
A green icon appears when regenerative braking is limited. See Regenerative Braking on page 262 for more
information.

Vehicle power is currently being limited because the energy remaining in the Battery is low, the vehicle's
systems are being heated or cooled, or an error is detected by the drive inverter.

38

Owner's Manual

Owners Manual
Instrument Panel
Instrument Panel Overview
The instrument panel changes depending on whether CybertruckModel SModel X is:
• Off (shown below).
• Driving (see Instrument Panel - Driving on page 44Instrument Panel - Driving on page 46Instrument Panel - Driving on
page 48).
• Charging (see Charging Status on page 467).
When CybertruckModel SModel X is off, the instrument panel shows remaining estimated range, status of doors, and outside
temperature. When you press the brake, indicator lights flash on briefly along the top. Unless an indicator light applies to a
current situation, it should turn off. If an indicator light fails to turn on or off, contact Tesla.
NOTE: The following illustration is provided for demonstration purposes only. Depending on vehicle options, software version,
and market region, the information displayed may be slightly different.

Owner's Manual

39

Owners Manual

The following indicators illuminate on the instrument panel to advise you or alert you of a specific condition.
If the touchscreen displays this red brake indicator at any time other than briefly when you first start
CybertruckModel SModel X, a brake system fault is detected, or the level of the brake fluid is low. Contact
Tesla immediately. Apply steady pressure and keep the brake pedal firmly pressed to stop the vehicle
when safe to do so.
USA:
Canada:

If the touchscreen displays this red brake indicator at any time other than briefly when you first start
CybertruckModel SModel X, a brake system fault is detected, or the level of the brake fluid is low.
Contact Tesla immediately. Apply steady pressure and keep the brake pedal firmly pressed to stop the
vehicle when safe to do so.

The touchscreen displays this amber brake indicator if a brake booster fault is detected. Apply steady
pressure and keep the brake pedal firmly pressed to stop the vehicle when safe to do so. Hydraulic Boost
Compensation will be active (see Hydraulic Boost Compensation on page 866).
USA:
The touchscreen displays this amber brake indicator if a brake booster fault is detected. Apply steady
pressure and keep the brake pedal firmly pressed to stop the vehicle when safe to do so. Hydraulic
Boost Compensation will be active (see Hydraulic Boost Compensation on page 866).
Canada:
The ABS indicator briefly flashes amber on the touchscreen when you first start
CybertruckModel SModel X. If this indicator lights up at any other time, an ABS fault has occurred and the
ABS is not operating. Contact Tesla. The braking system remains fully operational and is not affected by
an ABS failure. However, braking distances may increase. Drive cautiously and avoid heavy braking.
USA:
Canada:

40

The ABS indicator briefly flashes amber on the touchscreen when you first start
CybertruckModel SModel X. If this indicator lights up at any other time, an ABS fault has occurred and
the ABS is not operating. Contact Tesla. The braking system remains fully operational and is not affected
by an ABS failure. However, braking distances may increase. Drive cautiously and avoid heavy braking.

Owner's Manual

Owners Manual
When you manually apply the parking brake using the touchscreen, the red parking brake indicator lights
up on the touchscreen.
USA:
When you manually apply the parking brake using the touchscreen, the red parking brake indicator
lights up on the touchscreen.
Canada:
If the parking brake experiences an electrical issue, the amber parking brake indicator lights up and a fault
message displays on the touchscreen.
USA:
If the parking brake experiences an electrical issue, the amber parking brake indicator lights up and a
fault message displays on the touchscreen.
Canada:
Low beam headlights are on.

High beam headlights are on. Illuminates when high beams are on but the Auto High Beam setting is turned off
or if the Auto High Beam setting is turned on but is temporarily unavailable. See High Beam Headlights on page
253.

High beam headlights are currently turned on, and Auto High Beam is ready to turn off the high beams if light is
detected in front of CybertruckModel SModel X. See High Beam Headlights on page 253.

High beam headlights are temporarily turned off because Auto High Beam is on and is detecting light in front of
CybertruckModel SModel X. When light is no longer detected, the high beams automatically turn back on. See
High Beam Headlights on page 253.

Parking lights (side marker lights, tail lights, and license plate lights) are on. See Lights on page 250.

Front fog lights, if equipped. See Lights on page 250.

Adaptive Front Lighting, if equipped. See #unique_105 on page .

Owner's Manual

41

Owners Manual
Adaptive Front Lighting, if equipped. See Adaptive Front Lighting System (AFS) on page 254.

Electronic stability control systems are actively minimizing wheel spin by controlling brake pressure and motor
power (indicator flashes amber). See Traction Control on page 290. If this indicator remains on, a fault is
detected and you should immediately contact Tesla.

If a fault is detected that reduces the performance of the air suspension system, this amber indicator light
displays (see Air Suspension on page 266Air Suspension on page 269Air Suspension on page 271). If the
problem persists, contact Tesla.

If a fault is detected that disables the air suspension system, a red indicator lights up on the instrument panel
(see Air Suspension on page 266Air Suspension on page 269Air Suspension on page 271). Contact Tesla.

Airbag safety. If this red indicator does not flash on briefly when CybertruckModel SModel X prepares to drive,
or if it remains on, contact Tesla immediately. See Airbags on page 198Airbags on page 187.

Vehicle Hold is actively applying the brakes. See Vehicle Hold on page 287.

Tire pressure warning. The pressure of a tire is out of range. If a fault with the Tire Pressure Monitoring System
(TPMS) is detected, the indicator flashes. For a TPMS fault, contact Tesla. See Tire Care and Maintenance on
page 489.

A door or trunk is open. See Keys and Doors on page 80, Rear Trunk on page 100, or Front Trunk on page 109.

A seat belt for an occupied seat is not fastened. See Seat Belts on page 143.
NOTE: Depending on the date of manufacture, rear seating positions may not be equipped with a seat belt
reminder.

Electronic stability control systems are no longer minimizing wheel spin. On a Rear Wheel Drive vehicle, the
traction control system has been turned off, or on an All-Wheel Drive vehicle, Slip Start has been enabled. See
Traction Control on page 290.

CybertruckModel SModel X is in Transport mode and can roll freely. It does not automatically shift into Park
when you exit. See Instructions for Transporters on page 564Instructions for Transporters on page 572.

42

Owner's Manual

Owners Manual
Trailer mode (if equipped) is active. See Towing and Accessories on page 311.

Appears when some of the energy stored in the Battery may not be available due to cold weather conditions.
During these cold weather conditions, charging rates may also be limited. If CybertruckModel SModel X is
plugged in, you can heat your Battery by turning on climate control with the mobile app. The snowflake icon
disappears when the Battery is sufficiently warm.
Vehicle power is currently being limited because the energy remaining in the Battery is low or the vehicle's
systems are being heated or cooled.

Flashes green when the left turn signal is operating. Both turn signal indicators flash green when the hazard
warning flashers are operating.