appropriate turn signal engages and Autosteer maneuvers CybertruckModel SModel XModel 3Model Y onto the off-ramp or
interchange.
WARNING: Never depend on Navigate on Autopilot to determine an appropriate lane at an off-ramp. Stay alert and
perform visual checks to ensure that the driving lane is safe and appropriate.
When you leave a controlled-access highway (for example, you take an exit or you enter a section of the navigation route that
is no longer supported), Navigate on Autopilot reverts to Autosteer— a chime sounds and the instrument panel displays the
driving lane lines in blue (instead of the single blue in front of CybertruckModel SModel XModel 3Model Y).
NOTE: When determining navigation routes, and maneuvers at interchanges, Navigate on Autopilot considers whether or not
you want to use High Occupancy Vehicle (HOV) lanes. Therefore, ensure the Use HOV Lanes setting is appropriate for your
circumstances (see Maps and Navigation on page 704). If the setting is off, Navigate on Autopilot never uses a HOV lane,
regardless of time of day. If the setting is on, Navigate on Autopilot uses HOV lanes, whenever applicable.
WARNING: When Navigate on Autopilot deactivates, Autosteer remains active. Always be prepared to take appropriate
action.

596

Owner's Manual

Owners Manual
WARNING: Navigate on Autopilot may not always attempt to exit at an off-ramp or change lanes, even when an exit or
lane change is determined by the navigation route. Always remain alert and be prepared to manually steer onto an offramp, or make a lane change to prepare for, or to exit at, an off-ramp or interchange.
You can cancel Navigate on Autopilot at any time by touching Navigate on Autopilot on the map’s turn-by-turn direction list
(CybertruckModel SModel XModel 3Model Y reverts to Autosteer), or by canceling Autosteer entirely (see Canceling
Autosteer on page 591).
Lane Changes

Navigate on Autopilot changes lanes to either prepare CybertruckModel SModel XModel 3Model Y for an upcoming off-ramp,
to increase your driving speed (not to exceed your set cruising speed), or to move CybertruckModel SModel XModel 3Model
Y out of a passing lane when you are not actively passing other road users. A message displays at the top of the map's turnby-turn direction list to notify you when an upcoming lane change is required to stay on your navigation route. The instrument
panel displays the upcoming driving path:

When the instrument panel displays a message asking you to confirm the lane change, engage the appropriate turn signalor
pull the Autopilot stalk toward you. If you do not confirm the lane change within three seconds, a chime sounds to remind you
that Navigate on Autopilot requires your confirmation to change lanes.
If Require Lane Change Confirmation is turned off, Navigate on Autopilot engages the appropriate turn signal, checks for
vehicles and objects, and when appropriate, maneuvers CybertruckModel SModel XModel 3Model Y into the adjacent lane.
If Require Lane Change Confirmation is turned on, you must engage the appropriate turn signal or pull the Autopilot stalk
toward you to confirm that you want Navigate on Autopilot to proceed with the lane change. If you do not confirm the lane
change within three seconds, a chime sounds to remind you that Navigate on Autopilot requires your confirmation to change
lanes.

Owner's Manual

597

Owners Manual
NOTE: If you ignore a route-based lane change suggestion (for example, you are driving in the left lane while approaching an
off-ramp on the right side of the highway), Navigate on Autopilot is unable to maneuver onto the off-ramp and as a result, you
are re-routed to your destination.
WARNING: Navigate on Autopilot may not always attempt to exit at an off-ramp or change lanes, even when an exit or
lane change is determined by the navigation route. Always remain alert and be prepared to manually steer onto an offramp, or make a lane change to prepare for, or to exit at, an off-ramp or interchange.
Be Ready to Assist

When attempting to change lanes or maneuver CybertruckModel SModel XModel 3Model Y, or when approaching
construction zones, Navigate on Autopilot may be unable to determine the appropriate driving lane (for example, complex
clover leafs and multi-lane off-ramps) and the instrument panel displays an alert indicating that Navigate on Autopilot is trying
to maneuver and may require assistance. When you see the message, be prepared to take immediate action to ensure that it is
safe and appropriate to complete the lane change or maneuver.

598

Owner's Manual

Owners Manual
Traffic Light and Stop Sign Control
NOTE: Traffic Light and Stop Sign Control is a BETA feature and works best on roads that are frequently driven by Tesla vehicles.
Traffic Light and Stop Sign Control attempts to stop at all traffic lights and may also stop at green lights.
Traffic Light and Stop Sign Control is designed to recognize and respond to traffic lights and stop signs, slowing
CybertruckModel SModel XModel 3Model Y to a stop when using Traffic-Aware cruise control or Autosteer. This feature uses
the vehicle's forward-facing cameras, in addition to GPS data, and slows the car for all detected traffic lights, including green,
blinking yellow, and off lights in addition to stop signs and some road markings. As CybertruckModel SModel XModel 3Model
Y approaches an intersection, the instrument clustertouchscreen displays a notification indicating the intention to slow down.
You must confirm that you want to continue or CybertruckModel SModel XModel 3Model Y stops at the red line displayed on
the instrument clustertouchscreen's driving visualization.
WARNING: NEVER make assumptions and predict when and where Traffic Light and Stop Sign Control will stop or
continue through an intersection or road marking. From a driver's perspective, the behavior of Traffic Light and Stop
Sign Control may appear inconsistent. Always pay attention to the roadway and be prepared to take immediate action. It
is the driver's responsibility to determine whether to stop or continue through an intersection. Never depend on Traffic
Light and Stop Sign Control to determine when it is safe and/or appropriate to stop or continue through an intersection.
Before Using
Before using Traffic Light and Stop Sign Control, you must:
• Ensure that forward-facing cameras are unobstructed (see Cleaning a Camera on page 783Cleaning a Camera on page
783Cleaning a Camera on page 783Cleaning a Camera on page 784Cleaning a Camera on page 1144) and calibrated (see
Drive to Calibrate Cameras on page 108Drive to Calibrate Cameras on page 1144). Traffic Light and Stop Sign Control
depends on the ability of the cameras to detect traffic lights, stop signs, and road markings.
• Ensure that the latest version of maps has been downloaded to CybertruckModel SModel XModel 3Model Y. Although
Traffic Light and Stop Sign Control primarily uses visual data received from the vehicle's cameras, greater accuracy is
achieved when using the most recent map data. To check which version of maps is currently downloaded, touch Controls >
Software. You must connect to a Wi-Fi network to receive updated maps (see Map Updates on page 711).
• Enable the feature. With the vehicle in Park, touch Controls > Autopilot > Traffic Light and Stop Sign Control. Once enabled,
Traffic Light and Stop Sign Control operates whenever Traffic-Aware Cruise Control or Autosteer is active.
How it Works
When Traffic Light and Stop Sign Control is enabled and you are using Autosteer, Traffic-Aware Cruise Control, or Full SelfDriving (Supervised), the instrument clustertouchscreen displays a popup message to inform you that an upcoming traffic
light, stop sign, or road marking has been detected. As it approaches the stop location, even at an intersection where the traffic
light is green, CybertruckModel SModel XModel 3Model Y slows down and displays a red line to indicate where
CybertruckModel SModel XModel 3Model Y will stop. To continue through the intersection—even if the traffic light is green —
you must pull the Autopilot stalk toward you orpress down on the drive stalk orpress down on the drive stalk or briefly press
the accelerator pedal to give the vehicle permission to proceed. When you've confirmed that you want to proceed, the red
stop line turns gray and CybertruckModel SModel XModel 3Model Y continues through the intersection and resumes your set
cruising speed.
NOTE: If CybertruckModel SModel XModel 3Model Y is approaching a green light and detects that a vehicle in front of you is
continuing through the intersection, CybertruckModel SModel XModel 3Model Y continues through the intersection without
requiring your confirmation, provided you are not in a turning lane and the vehicle can detect that your hands are on the
steering wheelsteering yoke (or steering wheel).
NOTE: If, after you pull the Autopilot stalk toward you or press down on the drive stalk or press down on the drive stalk or
briefly press the accelerator pedal to confirm that you want to continue through the intersection, the traffic signal changes
before you enter the intersection (for example, the light changes from green to yellow or from yellow to red),
CybertruckModel SModel XModel 3Model Y may determine that it is not appropriate to proceed. Therefore,
CybertruckModel SModel XModel 3Model Y stops and you must press the accelerator to proceed. At all times, it is your
responsibility to ensure the vehicle stops or accelerates appropriately and safely.

Owner's Manual

599

Owners Manual
WARNING: Traffic Light and Stop Sign Control DOES NOT turn CybertruckModel SModel XModel 3Model Y through an
intersection unless Full Self-Driving (Supervised) is engaged. When in a turning lane, CybertruckModel SModel XModel
3Model Y stops at the red stop line. To proceed, pull the Autopilot stalk toward you or press down on the drive stalk or
press down on the drive stalk or briefly press the accelerator pedal—CybertruckModel SModel XModel 3Model Y
continues straight through the intersection (even when in a turning lane), so you MUST manually steer
CybertruckModel SModel XModel 3Model Y through the intersection (which cancels Autosteer).
Traffic Light and Stop Sign Control is designed to operate as described only when the following conditions are met:
• Autosteer, Full Self-Driving (Supervised), or Traffic-Aware Cruise Control is engaged.
• The cameras can detect an upcoming traffic light, stop sign or road marking (for example, cameras are unobstructed and
have a clear line-of-sight to the traffic light, stop sign, or road marking).
• The instrument clustertouchscreen on CybertruckModel SModel XModel 3Model Y is displaying an upcoming traffic light
in "bold" format. CybertruckModel SModel XModel 3Model Y does not acknowledge traffic lights that the instrument
clustertouchscreen shows as faded. If a traffic light is not directly ahead of the camera (for example, it is located at an
angle of the camera's view, or located in an adjacent lane) the instrument clustertouchscreen displays it as faded and
CybertruckModel SModel XModel 3Model Y does not slow down and stop for it.
WARNING: If the instrument clustertouchscreen is not displaying a red stop line at an upcoming intersection,
CybertruckModel SModel XModel 3Model Y does not slow down or stop. It is the driver's responsibility to pay attention
to upcoming intersections and monitor traffic conditions to determine when and if the vehicle should stop and then to
take appropriate action as needed.
WARNING: Never depend on Traffic Light and Stop Sign Control to determine whether to stop at, or proceed through, an
intersection. Drive attentively by watching the road and paying attention to the roadway, upcoming intersections, traffic
conditions, crosswalks, and other road users. It is always the driver's responsibility to determine whether to stop or
proceed. Be prepared to take immediate action. Failure to do so can result in injury or death.
WARNING: In some situations, Traffic Light and Stop Sign Control may inaccurately detect a traffic light or stop sign,
causing CybertruckModel SModel XModel 3Model Y to slow down unexpectedly. Be prepared to take immediate action
at all times.
WARNING: You must pull the Autopilot stalk toward you or press down on the drive stalk or press down on the drive stalk
or briefly press the accelerator pedal to confirm that you want to proceed through an intersection, regardless of the
status of the traffic light. If you do not confirm, CybertruckModel SModel XModel 3Model Y stops at the red stop line
displayed on the instrument clustertouchscreen, even if stopping may be inappropriate. Stopping at a green light may
confuse other drivers and may result in a collision, injury or death. Therefore, always pay attention to upcoming
intersections and be prepared to manually brake or accelerate in response to surroundings.
WARNING: Never assume that your ability to see a traffic light, stop sign, or road marking (especially at a complex
intersection, or an intersection in which a traffic light or sign is partially obstructed, etc.) means that
CybertruckModel SModel XModel 3Model Y can also see it and respond appropriately.
WARNING: Even the most recent map data does not include all traffic lights and stop signs. Therefore, Traffic Light and
Stop Sign Control relies heavily on the ability of the cameras to detect traffic lights, stop signs, road markings, etc. As a
result, CybertruckModel SModel XModel 3Model Y may ignore an intersection that is blocked from the camera's view
(for example, obstructed by a tree or a large vehicle or object, or located near a steep hill or sharp curve).
WARNING: Traffic Light and Stop Sign Control is not a substitute for attentive driving and sound judgment.

600

Owner's Manual

Owners Manual
Traffic Lights

When driving with Autosteer or Traffic-Aware Cruise Control engaged, and Traffic Light and Stop Sign Control enabled,
CybertruckModel SModel XModel 3Model Y is designed to respond as follows when approaching intersections controlled by
a traffic light:
Type of Traffic Light

Vehicle Intended Response
At a solid green traffic light, or at a traffic light that is currently off (not illuminated),
CybertruckModel SModel XModel 3Model Y slows down.
If you are following a car in front of you that continues through the intersection, the
instrument clustertouchscreen displays a green stop line and provided your hands are
detected on the steering wheelsteering yoke (or steering wheel),
CybertruckModel SModel XModel 3Model Y also continues. If a car is not in front of you,
the instrument clustertouchscreen displays a red stop line and you must confirm that you
want to continue through the intersection by pulling the Autopilot stalk toward you or
press down on the drive stalk or press down on the drive stalk or briefly pressing the
accelerator pedal. If you don’t confirm, CybertruckModel SModel XModel 3Model Y
stops at the red stop line.
NOTE: CybertruckModel SModel XModel 3Model Y resumes the set cruising speed when
it continues through the intersection, taking into consideration the speed of a vehicle in
front of you.

CybertruckModel SModel XModel 3Model Y slows down and comes to a complete stop at
the red stop line displayed on the instrument clustertouchscreen. When you want to
continue through the intersection (for example, the light turns green again, or once
CybertruckModel SModel XModel 3Model Y has come to a complete stop), you must pull
the Autopilot stalk toward you or press down on the drive stalk or press down on the drive
stalk or briefly press the accelerator pedal.

CybertruckModel SModel XModel 3Model Y slows down and comes to a complete stop at
the red stop line displayed on the instrument clustertouchscreen. When you want to
proceed through the intersection (for example, the light turns green again), you must pull
the Autopilot stalk toward you or press down on the drive stalk or press down on the drive
stalk or briefly press the accelerator pedal.
NOTE: If the traffic light changes after you've confirmed that you want to proceed (for
example, a green traffic light turns yellow), CybertruckModel SModel XModel 3Model Y
may stop instead of continuing, especially if CybertruckModel SModel XModel 3Model Y
determines that it can safely stop before entering the intersection.
NOTE: CybertruckModel SModel XModel 3Model Y is not designed to proceed through
an intersection when the traffic light is red or if the light turns yellow in situations when
there is adequate distance to safely stop before entering the intersection.
NOTE: You can take over driving at any time by manually braking to cancel Autosteer or
Traffic-Aware Cruise Control.

Owner's Manual

601

Owners Manual
Type of Traffic Light

Vehicle Intended Response

CybertruckModel SModel XModel 3Model Y slows down. To proceed, you must pull the
Autopilot stalk toward you or press down on the drive stalk or press down on the drive
stalk or briefly press the accelerator pedal. If you don’t,
CybertruckModel SModel XModel 3Model Y stops at the red stop line displayed on the
instrument clustertouchscreen.
NOTE: To prevent CybertruckModel SModel XModel 3Model Y from stopping, and to
minimize how much it slows down as it approaches, you can confirm that you want to
proceed by pulling the Autopilot stalk toward you or press down on the drive stalk or
press down on the drive stalk or briefly pressing the accelerator pedal at any time after
the instrument clustertouchscreen displays the red stop line.
CybertruckModel SModel XModel 3Model Y resumes your set cruising speed
immediately after you confirm (taking into consideration the speed of a vehicle in front of
you).
WARNING: Approach attentively and be prepared to press the brake pedal to slow
down or stop.

CybertruckModel SModel XModel 3Model Y slows down and comes to a complete stop at
the red stop line displayed on the instrument clustertouchscreen. When you want to
proceed through the intersection (for example, traffic laws and conditions indicate it is
safe and legal to proceed), you must pull the Autopilot stalk toward you or press down on
the drive stalk or press down on the drive stalk or briefly press the accelerator pedal.

602

Owner's Manual

Owners Manual
Stop Signs and Road Markings

When driving with Autosteer or Traffic-Aware Cruise Control engaged, and Traffic Light and Stop Sign Control enabled,
CybertruckModel SModel XModel 3Model Y is designed to respond as follows when approaching intersections controlled by
stop signs, stop lines, or road markings:
Type of Intersection

Vehicle Intended Response
CybertruckModel SModel XModel 3Model Y assumes the right of way and continues straight
without slowing down or stopping.

No Traffic Control

Arm of T-junction
If CybertruckModel SModel XModel 3Model Y detects a T-junction based on the map data,
CybertruckModel SModel XModel 3Model Y slows down and comes to a complete stop at the
red stop line displayed on the instrument clustertouchscreen. When you want to proceed, you
must take over steering and acceleration.
WARNING: CybertruckModel SModel XModel 3Model Y may not stop at a T-junction
that does not have a stop sign or stop line, or if the T-junction is not included in the map
data. Drive attentively and be prepared to stop (when necessary and/or appropriate).

End of T-junction
CybertruckModel SModel XModel 3Model Y slows down and comes to a complete stop at the
red stop line displayed on the instrument clustertouchscreen. When you want to proceed
through the intersection, you must pull the Autopilot stalk toward you or press down on the
drive stalk or press down on the drive stalk or briefly press the accelerator pedal.
NOTE: If you confirm that you want to proceed through an intersection controlled by a stop
sign by pulling the Autopilot stalk toward you or press down on the drive stalk or press down
on the drive stalk or briefly pressing the accelerator pedal before
CybertruckModel SModel XModel 3Model Y has stopped, your confirmation is ignored.
CybertruckModel SModel XModel 3Model Y is not designed to proceed through a stop sign
without stopping.
Stop Sign

Owner's Manual

NOTE: Even when using Autosteer, and even if you have engaged a turn signal, you must turn
the steering wheelsteering yoke (or steering wheel) yourself (which cancels Autosteer) to
complete a turn at an intersection.

603

Owners Manual
Type of Intersection

Vehicle Intended Response

Stop Sign and Road Marking

Road Marking
WARNING: CybertruckModel SModel XModel 3Model Y also slows down and stops at a roundabout. You must take over
steering (which cancels Autosteer) and pull the Autopilot stalk toward you or press down on the drive stalk or press
down on the drive stalk or briefly press the accelerator pedal to confirm that you want to continue through the
roundabout.
WARNING: At crosswalks, CybertruckModel SModel XModel 3Model Y may slow down and may stop, depending on
whether the crosswalk is controlled by a traffic light and whether the cameras detect pedestrians, bicyclists, etc. in the
crosswalk. Pay particular attention at crosswalks and be prepared to take over at any time. Failure to do so can result in
injury or death.
Limitations
Depending on many different circumstances and environmental conditions, Traffic Light and Stop Sign Control may or may not
stop at:
• Railroad crossings.
• Keep-out zones.
• Toll booths.
• Crosswalk systems.
• Yield signs or temporary traffic lights and stop signs (such as at construction areas).
• Miscellaneous traffic U-turn lights, bicycle and pedestrian crossing lights, lane availability lights, etc.
In addition, Traffic Light and Stop Sign Control is particularly unlikely to operate as intended, can disengage, or may not
operate, when one or more of the following conditions are present:
• Driving through consecutive light-controlled intersections that are very close to each other.
• Visibility is poor (heavy rain, snow, fog, etc.) or weather conditions are interfering with camera or sensor operation.
• Bright light (such as direct sunlight) is interfering with the view of the camera(s).

604

Owner's Manual

Owners Manual
• A camera is obstructed, covered, damaged, or not properly calibrated.
• Driving on a hill or on a road that has sharp curves on which the cameras are unable to see upcoming traffic lights or stop
signs.
• A traffic light, stop sign, or road marking is obstructed (for example, a tree, a large vehicle, etc.).
• CybertruckModel SModel XModel 3Model Y is being driven very close to a vehicle in front of it, which is blocking the view
of a camera.
WARNING: The limitations listed above are not an exhaustive list of reasons why CybertruckModel SModel XModel
3Model Y may not operate as expected. Many unforeseen circumstances can adversely impact the accurate operation
of Traffic Light and Stop Sign Control. Using this feature does not reduce or eliminate the need to drive attentively and
responsibly. You must be prepared to take appropriate and immediate action at all times.

Full Self-Driving (Supervised)
When Full Self-Driving (Supervised) (also referred to as Autosteer on City Streets) is engaged,
CybertruckModel SModel XModel 3Model Y attempts to drive to your destination by following curves in the road, stopping at
and negotiating intersections, making left and right turns, navigating roundabouts, and entering/exiting highways.
Unlike Traffic-Aware Cruise Control, Autosteer, and Navigate on Autopilot, which are intended for use on multi-lane roadways
with clear lane markings, Full Self-Driving (Supervised) is meant to work in a variety of driving scenarios. You can use Full SelfDriving (Supervised) on any type of roadway, including residential and city streets.
WARNING: Driver intervention may be required in certain situations, such as on narrow roads with oncoming cars, in
construction zones, or while going through complex intersections. For more examples of scenarios in which driver
intervention might be required, see Limitations and Warnings on page 633.
Full Self-Driving (Supervised) uses inputs from cameras mounted at the front, rear, left, and right of
CybertruckModel SModel XModel 3Model Y to build a model of the area surrounding CybertruckModel SModel XModel
3Model Y (see Cameras on page 101). The Full Self-Driving computer installed in CybertruckModel SModel XModel 3Model Y
is designed to use this input, rapidly process neural networks, and make decisions to safely guide you to your destination.
NOTE: As Tesla’s Full Self-Driving (Supervised) capabilities evolve, CybertruckModel SModel XModel 3Model Y is upgraded
through over-the-air software updates. Download updates as soon as they become available.
NOTE: Full Self-Driving (Supervised) uses Tesla's vision-based system and therefore radar (if equipped) is disabled.
Like other Autopilot features, Full Self-Driving (Supervised) requires a fully attentive driver and will display a series of
escalating warnings requiring driver response. You must keep your hands on the steering wheelsteering yoke (or steering
wheel) while Full Self-Driving (Supervised) is engaged. While Full Self-Driving (Supervised) is engaged, the cabin camera
monitors driver attentiveness (see Driver Attentiveness on page 610).
WARNING: Full Self-Driving (Supervised) is a hands-on feature that requires you to pay attention to the road at all times.
Keep your hands on the steering wheelsteering yoke (or steering wheel) at all times, be mindful of road conditions and
surrounding traffic, pay attention to pedestrians and cyclists, and always be prepared to take immediate action
(especially around blind corners, crossing intersections, and in narrow driving situations). Failure to follow these
instructions could cause damage, serious injury or death. It is your responsibility to familiarize yourself with the
limitations of Full Self-Driving (Supervised) and the situations in which it may not work as expected. For more
information, see Limitations and Warnings on page 633.
CAUTION: Use of Full Self-Driving (Supervised) will be suspended if improper usage is detected. For more information,
see Autopilot Suspension on page 610.
CAUTION: As Full Self-Driving (Supervised) deployment expands, Tesla will gradually make it available to eligible
customers in select countries outside of the United States and Canada. Because every country contains unique
infrastructure, driving behaviors, and traffic patterns that Full Self-Driving (Supervised) must adapt to over time, it is
essential for drivers using Full Self-Driving (Supervised) in newly eligible countries to be extra attentive and overly
cautious. You must be ready to take over safely at any time.
Before Using Full Self-Driving (Supervised)
Before using Full Self-Driving (Supervised), you must:

Owner's Manual

605

Owners Manual
• Ensure that the cameras on CybertruckModel SModel XModel 3Model Y are unobstructed and calibrated (see Cameras on
page 101). Full Self-Driving (Supervised) depends on the ability of the cameras to detect traffic lights, stop signs, and road
markings.
• Ensure that the latest version of maps has been downloaded to CybertruckModel SModel XModel 3Model Y. Although Full
Self-Driving (Supervised) primarily uses visual data received from the vehicle's cameras, greater accuracy is achieved
when using the most recent map data. To check which version of maps is currently downloaded, touch Controls > Software.
You must connect to a Wi-Fi network to receive updated maps (see Map Updates on page 711).
In addition, you must enable Full Self-Driving (Supervised) before you can use it. To enable Full Self-Driving (Supervised),
touch Controls > Autopilot > Full Self-Driving (Supervised) and then, after carefully reading and understanding the popup
window, touch Yes.
NOTE: When Full Self-Driving (Supervised) is enabled, the setting for Autopilot Activation is set to Single Click and TrafficAware Cruise Control and Autosteer are unavailable.
NOTE: When Full Self-Driving (Supervised) is enabled, the setting for Autopilot Activation is set to Single Click and TrafficAware Cruise Control and Autosteer are unavailable.
NOTE: When Full Self-Driving (Supervised) is enabled, the setting for Autopilot Activation is set to Single Pull and TrafficAware Cruise Control and Autosteer are unavailable.
NOTE: When Full Self-Driving (Supervised) is enabled, the setting for Autopilot Activation is set to Single Pull and TrafficAware Cruise Control and Autosteer are unavailable.
Customize Full Self-Driving (Supervised) settings by touching Controls > Autopilot.
• Full Self-Driving (Supervised): If desired, change the default setting of Average to Chill or Assertive. Chill provides a more
relaxed driving style and Assertive drives with more urgency.
• Minimal Lane Changes for the Current Drive: When selected, Full Self-Driving (Supervised) makes fewer lane changes on
the current drive. CybertruckModel SModel XModel 3Model Y will still make lane changes as necessary to follow the
navigation route.
NOTE: While Full Self-Driving (Supervised) is selected, tilting the right steering wheelsteering yoke (or steering wheel)
button to the right or left also allows you to change the Full Self-Driving (Supervised) profile and enable or disable Minimal
Lane Changes.
• Automatic Set Speed Offset: When enabled, CybertruckModel SModel XModel 3Model Y drives at the speed that Autopilot
determines to be the most natural. This considers factors like road type, traffic flow, environmental conditions, the
detected speed limit, and the selected Full Self-Driving (Supervised) profile setting.
WARNING: You are responsible for the speed of the vehicle at all times, whether Autopilot is engaged or not.

To Use Full Self-Driving (Supervised)
Once Full Self-Driving (Supervised) is enabled, activate it the same way you would Autosteer (see Autosteer on page
556Autosteer on page 588).
1. Enter a destination. If you do not choose a destination, CybertruckModel SModel XModel 3Model Y chooses the most
probable driving path or suggests a destination based on your driving.
2. When the instrument clustertouchscreen displays the gray steering wheelsteering yoke (or steering wheel) icon, press the
right scroll wheelpress the right scroll wheelpull the drive stalk down once fullypull the drive stalk once fullypull the
Autopilot stalk toward you.

606

Owner's Manual

Owners Manual

You can engage Full Self-Driving (Supervised) at any speed less than 85 mph (150 km/h), including when
CybertruckModel SModel XModel 3Model Y is at a standstill.
The instrument clustertouchscreen displays the maximum speed in blue. When you engage Full Self-Driving (Supervised), the
set cruising speed defaults to the speed limit, plus any offset you’ve specified. If Autopilot is unable to determine the speed
limit, the cruising speed is your current speed, in addition to any specified offset.

Owner's Manual

607

Owners Manual
To indicate that Full Self-Driving (Supervised) is available but not engaged, the top corner of the
touchscreen displays a gray steering wheelsteering yoke (or steering wheel) icon next to the
driving gear.

When Full Self-Driving (Supervised) is engaged, the steering wheelsteering yoke (or steering
wheel) icon is blue and a blue line represents your driving path.

When Full Self-Driving (Supervised) is engaged, the instrument clustertouchscreen displays a visualization of the environment
surrounding CybertruckModel SModel XModel 3Model Y, including the roadway and detected objects such as vehicles,
pedestrians, curbs, bicyclists, and more. Objects that are highlighted on the visualization represent priorities that Full SelfDriving (Supervised) is actively controlling for at a given time.
NOTE: The Full Self-Driving (Supervised) visualization may not be a holistic representation of the objects, road markings, road
signals, and other variables that Full Self-Driving (Supervised) takes into account as it attempts to drive to your destination.
While Full Self-Driving (Supervised) is engaged, it uses data from the cameras on CybertruckModel SModel XModel 3Model Y
that may not be represented in the visualization (see Cameras on page 101).
NOTE: Full Self-Driving (Supervised) uses Tesla’s vision-based system and therefore radar (if equipped) is disabled.

The visualization will also inform you of the system’s intended action by displaying a message on the instrument
clustertouchscreen, such as when the vehicle is slowly creeping for visibility to take a turn at an intersection.
You can widen the visualization area to fullscreen. Enable the setting by touching Controls > Autopilot > Full Self-Driving
(Supervised) > Expanded Full Self-Driving Visualization. Then on the touchscreen, swipe the visualization window handle to fill
the entire screen.
NOTE: You can override Full Self-Driving (Supervised) at any time if you are uncomfortable or uncertain about the system’s
intended course of action. You are driving CybertruckModel SModel XModel 3Model Y at all times.
Canceling Full Self-Driving (Supervised)
To disengage Full Self-Driving (Supervised), do any of the following:
• Press the brake pedal.
• Move the drive stalk upward.
◦ CAUTION: If you move the drive stalk upward and hold it up for more than one second,
CybertruckModel SModel XModel 3Model Y shifts into Neutral after canceling Autosteer.
• Move the drive stalk upward.
◦ CAUTION: If you move the drive stalk upward and hold it up for more than one second,
CybertruckModel SModel XModel 3Model Y shifts into Neutral after canceling Autosteer.
• Press the right scroll wheel on the steering yoke (or steering wheel).
608

Owner's Manual

Owners Manual
• Press the right scroll wheel on the steering wheelsteering yoke (or steering wheel)
• Push the Autopilot stalk away from you once.
• Take over and steer manually.
When you disengage Full Self-Driving (Supervised) by steering manually, Traffic-Aware Cruise Control remains active.
In addition, Full Self-Driving (Supervised) will disengage if any of the following occurs:
• You shift out of Drive.
• A door or trunk is opened.
• There is an Automatic Emergency Braking event (see Collision Avoidance Assist on page 647).
• The driver's seatbelt is released, and/or the driver gets out of their seat.
• You do not respond to repeated reminders to keep your hands on the wheel and subsequent messages on the instrument
clustertouchscreen.
• Full Self-Driving (Supervised) becomes unavailable. This can happen for a number of reasons (for example, if a camera
becomes obscured). If Full Self-Driving (Supervised) disengages, an alert will appear on the instrument clustertouchscreen
to notify you and a chime will sound. If this happens, take control of steering immediately.
When driver intervention is required, it is best to safely disengage as soon as possible. It is recommended to practice
disengaging from Full Self-Driving (Supervised) in safe environment without other road users so you may become familiar with
the process.
While Using Full Self-Driving (Supervised)
Full Self-Driving (Supervised) changes lanes, makes left and right turns, follows on- and off-ramps, and takes forks in the road
as necessary to reach the destination.
WARNING: NEVER make assumptions and predict when and where Full Self-Driving (Supervised) will stop or continue
through an intersection or road marking. From a driver's perspective, the behavior of Full Self-Driving (Supervised) may
appear inconsistent. Always pay attention to the roadway and be prepared to take immediate action. It is the driver's
responsibility to determine whether to stop or continue through an intersection. Never depend on Full Self-Driving
(Supervised) to determine when it is safe and/or appropriate to stop or continue through an intersection.
Like Autosteer and Traffic-Aware Cruise Control, Full Self-Driving (Supervised) maintains your speed and following distance
from the vehicle ahead of CybertruckModel SModel XModel 3Model Y, if there is one. Full Self-Driving (Supervised) also
slows down and stops at traffic lights and stop signs as necessary, and reacts to pedestrians, cyclists, and other vehicles on
the road.
For example, if you are driving on a residential street and another vehicle backs out of a driveway ahead of
CybertruckModel SModel XModel 3Model Y, Full Self-Driving (Supervised) slows down or stops as appropriate. If the other
vehicle stops backing out while partially blocking the driving lane, Full Self-Driving (Supervised) slows down and maneuvers
around the other vehicle if the width of the lane allows it.
When the traffic in front of you is slowing down, Full Self-Driving (Supervised) shows blue arrows in the driving lane and slows
down to maintain an appropriate following distance from the vehicle ahead of you. When you are driving on the highway, Full
Self-Driving (Supervised) displays a message on the instrument clustertouchscreen to inform you when an action (such as a
lane change) is being taken.
WARNING: In rare cases, Full Self-Driving (Supervised) may not appropriately slow down, come to a stop, or resume
control for a stop sign or traffic light. You may assist the system by lightly applying the accelerator, or can override Full
Self-Driving (Supervised) at any time.
Changing Lanes

To tell Full Self-Driving (Supervised) to change lanes while on a multi-lane roadway, engage the right or left turn signal. On city
or residential streets, engaging the right or left turn signal tells Full Self-Driving (Supervised) to make a right or left turn,
respectively.

Owner's Manual

609

Owners Manual
Unlike Navigate on Autopilot, Full Self-Driving (Supervised) does not require confirmation before a lane change. To cancel a
lane change or turn, cancel the turn signal or intervene with the steering wheelsteering yoke (or steering wheel) or other
vehicle controls.
To be notified by a Chime, Vibration, or Both of upcoming lane changes (in addition to the notification on the instrument
clustertouchscreen), touch Controls > Autopilot > Full Self-Driving (Supervised) and then select a Lane Change Notification.
Changing the Set Speed

While Full Self-Driving (Supervised) is active, move the Autopilot stalk up to increase, or down to decrease, the set speed until
the instrument panel displays your desired cruising speed.
While Full Self-Driving (Supervised) is active, roll the right scroll wheel up to increase, or down to decrease, the set speed.
NOTE: In some cases, your speed is limited by the speed limit, the type of roadway, or the flow of traffic. If this is the case, Full
Self-Driving (Supervised) displays a message at the top of the visualization.
Arriving at Your Destination
Once you reach your destination, Full Self-Driving (Supervised) stops CybertruckModel SModel XModel 3Model Y and
displays a message indicating that navigation is complete.
Driver Attentiveness
Like other Autopilot features, Full Self-Driving (Supervised) requires driver attentiveness. Your hands must be on the steering
wheel at all times while Full Self-Driving (Supervised) is engaged, and you must monitor your surroundings, the road, and other
road users.
WARNING: The use of devices designed to circumvent driver attentiveness is a violation of the terms of use for Full SelfDriving (Supervised) and may result in the feature being permanently disabled on your vehicle and a ban on future use of
the feature.
Full Self-Driving (Supervised) periodically displays a message reminding the driver to apply slight force to the steering wheel:
Apply slight turning force to steering wheel

If CybertruckModel SModel XModel 3Model Y does not detect slight turning force on the steering wheel, the instrument
clustertouchscreen flashes and eventually chimes repeatedly. Do not use handheld devices while using Full Self-Driving
(Supervised). If the cabin camera detects a handheld device while Full Self-Driving (Supervised) is engaged, the instrument
clustertouchscreen displays a message reminding you to keep your hands on the wheel.
Similarly, the cabin camera monitors your continued attentiveness when using Full Self-Driving (Supervised). This system
cannot be disabled. The instrument clustertouchscreen displays a message reminding you to pay attention if you repeatedly
look away from the road, obstruct the camera, or prevent the system from identifying your gaze.
If you repeatedly ignore prompts to apply slight force to the steering wheel or to pay attention, Full Self-Driving (Supervised)
disables for the rest of the drive and displays the following message requesting you to drive manually. If you don't resume
manual steering, Full Self-Driving (Supervised) sounds a continuous chime, turns on the warning flashers, and slows the
vehicle to a complete stop.
Autopilot unavailable for current drive. Autopilot Strikeout - Attention warnings ignored.

Autopilot Suspension
Use of Autopilot features will be suspended if improper usage is detected.

610

Owner's Manual

Owners Manual
Use of Autosteer and Full Self-Driving (Supervised) is suspended for a week when you or another driver of your vehicle
receives fivethree Autopilot "strikeouts." A strikeout is when the Autopilot system disengages for the remainder of a trip after
the driver receives several audio and visual warnings for inattentiveness.
You can see how many strikeouts are remaining before Autopilot access is suspended by touching Controls > Autopilot.
A strikeout is forgiven after 7 days, as long as you don't receive another strikeout in that time.
NOTE: If your access to Autosteer and Full Self-Driving (Supervised) is suspended, you also lose access to Autopark.
However, you can still use Traffic-Aware Cruise Control and all active safety features are still enabled.
There may be occasions where driver intervention is required and you must take over immediately to maintain safe driving.
Driver-initiated disengagements do not count as improper usage and are expected from the driver.

Autopark
This feature may be temporarily limited or inactive until it is enabled with a future software update for vehicles manufactured
as of approximately October 2022.This feature may be temporarily limited or inactive until it is enabled with a future software
update for vehicles manufactured as of approximately October 2022.This feature may be temporarily limited or inactive until it
is enabled with a future software update for vehicles manufactured as of approximately September 2023.This feature may be
temporarily limited or inactive until it is enabled with a future software update for vehicles manufactured as of approximately
January 2023.This feature may be temporarily limited or inactive until it is enabled with a future software update for vehicles
manufactured as of approximately late May 2023.
Autopark uses data to simplify parking on public roads by maneuvering CybertruckModel SModel XModel 3Model Y into
parallel and perpendicular parking spaces.
CAUTION: Ensure all cameras and sensors (if equipped) are clean. Dirty cameras and sensors, as well as environmental
conditions such as rain and faded lane markings, can affect Autopilot performance.
WARNING: Autopark's performance depends on the ability of the cameras and sensors (if equipped) to determine the
vehicle's proximity to curbs, objects, and other vehicles.
WARNING: Do not use Autopark if anything, such as a ball hitch, bike rack, or trailer, is attached to the tow hitch.
Autopark may not stop for hitches when parking between or in front of other vehicles.
Parameters
Autopark detects potential parking spaces based on the following parameters:
Perpendicular Parking
• Your driving speed must be below 8 mph (13 km/h). If driving too fast, Autopark may not be able to accurately detect your
desired parking space.
• The parking space must be at least 7.2 feet (2.2 meters) wide.
• The parking space must have at least three visible lines for the vehicle to park into, such as parking lines, road markings, or
distinct curbs. Autopark may not work in a garage, for example, without three visible parking lines.