NZLADHL5C

4112A-ADHL5C

CarPC

Tesla

1960000

--

CarPC

Tesla

1960600

--

Wireless Charger

Tesla

WC4

BT USB hub

Tesla

1642783

In-Cabin Radar*

Tesla

Wireless Charger

Tesla

XMR2020AG525RGL 10224A-2020AG525R
YZP-ATC5CPC001
7414C-ATC5CPC001

XMR2020AG525RGL 10224A-2020AG525R
YZP-ATC5CPC001
7414C-ATC5CPC001
2AEIM-WC4

20098-WC4

2400-2483.5

2AEIM-1642783

20098-1642783

1616631

60000-64000

2AEIM-1616631

20098-1616631

WC3

127.72 KHz

2AEIM-WC3

20098-WC3

127.72 KHz
13.56
2400-2483.5

*The in-cabin radar is restricted to factory installation.
The devices listed above comply with Part 15 of the FCC rules and Industry Canada's license-exempt RSS Standard(s) and EU
Directive 2014/53/EU.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Tesla could void your authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.

Radiation Exposure Statement
The products comply with the FCC/ISED RF Exposure for Low Power Consumer Wireless Power Transfer. RF exposure limits
are set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The farthest RF
exposure demonstrated by compliance was at 20cm and farther from the user's body; set the device to low output power if
such function is available.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour unenvironnement non contrôlé.
Déclaration d'exposition aux radiations
Le produit est conforme à l'exposition RF ISED pour le transfert de puissance sans fil de consommateurs de faible puissance.
La limite d'exposition RF fixée pour un environnement non contrôlé est sans danger pour le fonctionnement prévu tel que
décrit dans ce manuel. L'exposition RF supplémentaire que la conformité a été démontrée à 20cm et plus de séparation du
corps de l'utilisateur ou de mettre l'appareil à la puissance de sortie inférieure si une telle fonction est disponible.

Owner's Manual

1107

Radio Regulatory Compliance
Radio Frequency Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician to help.
CAUTION: This equipment and its antennas must not be co-located or operated with another antenna or transmitter.

Canada
CAN ICES-3 (B)/NMB-3(B)
Leprésent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareilne doit pas produire de brouillage, et (2) l'utilisateurde
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
lefonctionnement.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour unenvironnement non contrôlé.
Déclaration d'exposition aux radiations:
Le produit est conforme à l'exposition RF ISED pour le transfert de puissance sans fil de consommateurs de faible puissance.
La limite d'exposition RF fixée pour un environnement non contrôlé est sans danger pour le fonctionnement prévu tel que
décrit dans ce manuel. L'exposition RF supplémentaire que la conformité a été démontrée à 20cm et plus de séparation du
corps de l'utilisateur ou de mettre l'appareil à la puissance de sortie inférieure si une telle fonction est disponible.

Mexico
IFT-008-SCFI-2015 / NOM-208-SCFI-2016
TPMS, model: 1472547G, IFT#: RCPTE1421-4384
La operación de este equipo está sujeta a las siguientes dos condiciones:
1. Es posible que este equipo o dispositivo no cause interferencia perjudicial.
2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

1108

Owner's Manual

Overview
Exterior

1. Signature light bar (Lights on page 1229)
2. Autopilot cameras (Cameras on page 1136)
3. Wiper blade (Windshield Wiper and Washers on page 1233)
4. Exterior mirrors (Mirrors on page 1226)
5. Front exterior door release button (Doors on page 1146)
6. Key card reader (Keys on page 1142)
7. Rear exterior door release button (Doors on page 1146)
8. Powered frunk (Powered Frunk on page 1185)
9. Front tow hooks (Instructions for Transporters on page 1442)
10. Front exterior lights (Lights on page 1229)
11. Wheels and tires (Wheel and Tire Specifications on page 1407)

Owner's Manual

1109

Overview

1. Tonneau cover (Cargo Bed on page 1188)
2. Cargo bed (Cargo Bed on page 1188)
3. Rear-facing camera (Rear-Facing Camera on page 1138)
4. Charge port (Charging Instructions on page 1370)
5. Exterior cargo bed switch (Accessing the Cargo Bed on page 1189)
6. Tow hitch cover (Towing a Trailer on page 1258)
7. Tailgate (Cargo Bed on page 1188)

1110

Owner's Manual

Overview
Interior

1. Interior door open button (Doors on page 1146)
2. Blind spot indicator and speaker (Blind Spot Warning Light on page 643)
3. Left scroll button (Left Scroll Button on page 1222)
4. Horn (Horn on page 1224)
5. Right scroll button (Right Scroll Button on page 1224)
6. Touchscreen (Touchscreen on page 1112)
7. Secondary drive mode selector on overhead console (Shifting on page 405)
8. Cabin camera (Cabin Camera on page 1139)
9. Hazard warning flashers (Hazard Warning Flashers on page 1231)
10. Front passenger dome light (Lights on page 1229)
CAUTION: CybertruckModel SModel XModel 3Model Y is equipped with an in-cabin sensor located near the front passenger dome
light to ensure certain vehicle and safety components are working properly. Do not block or obstruct the sensor. Doing so may
cause inaccurate readings, such as for occupant detection, parking brake engagement, vehicle display settings, etc.
11. Climate control vent (Adjusting the Front and Rear Vents on page 1343)
12. Power window switches (Windows on page 1150)
13. Manual door release (Opening Doors with No Power on page 1454)
14. Brake pedal (Braking and Stopping on page 1235)
15. Accelerator pedal (On-Road Modes on page 1242)
16. Wireless phone chargers and key card readers (Wireless Phone Chargers on page 1126 and Key Card on page 1143)
17. Center console (Center Console on page 1181)

Owner's Manual

1111

Overview
18. Glovebox (Glovebox on page 1183)

1. Rear touchscreen (Rear Touchscreen on page 1117)
2. Rear climate control vents (Adjusting the Front and Rear Vents on page 1343)
3. USB ports (USB-C Ports on page 1125)
4. Rear outlet (120V) (Interior Electronics on page 1125)
5. Cup holders (Rear Console on page 1181)
6. Rear door mechanical release (Opening a Rear Door with No Power on page 1454)
NOTE: The door mechnical release should only be used in emergency situations.

Touchscreen
NOTE: Throughout this Owner's Manual, the front touchscreen is referred to as the "touchscreen" whereas the rear
touchscreen is referred to as the "rear touchscreen".
WARNING: Always pay attention to road and traffic conditions when driving. To minimize driver distraction and ensure
the safety of vehicle occupants as well as other road users, avoid using the touchscreen to adjust settings while the
vehicle is in motion.

1112

Owner's Manual

Overview
Use the touchscreen to control many features that, in traditional vehicles, are controlled using physical buttons (for example,
adjusting the cabin heating and air conditioning, headlights, etc.). You also use the touchscreen to control media, navigate,
use entertainment features, and customize CybertruckModel SModel XModel 3Model Y to suit your preferences. For handsfree access to common touchscreen controls, use voice commands (see Voice Commands on page 97).
If the touchscreen is unresponsive or demonstrates unusual behavior, you can restart it (see Restarting the Touchscreen on
page 1115).
CAUTION: Do not apply a screen protector on the touchscreen. Doing so can result in unintended inputs to the
touchscreen (phantom inputs), delayed response or unresponsiveness to touches, electrostatic discharge which can
damage the touchscreen, etc. Any damage caused by installing a screen protector is not covered by the warranty.
The following shows the touchscreen while CybertruckModel SModel XModel 3Model Y is parked.
NOTE: Illustrations are provided to improve conceptual understanding only. Depending on vehicle options, software version,
market region and regional and language settings, the details displayed on the screen will differ.

1. Navigation: Find or navigate to a destination (see Maps and Navigation on page 699).
2. Status bar: This area on the top of the touchscreen displays the time of day, the outside temperature, and more (see Top
Status Bar Icons on page 1114).
3. Drive mode strip: Use to shift into Park, Reverse, or Drive. Swipe right from the upper-left side of the screen to display the
drive mode strip (see Shifting on page 405).
NOTE: To shift into Neutral, open Controls, then press and hold the Neutral icon.
4. Vehicle status: This area dynamically displays the current status of CybertruckModel SModel XModel 3Model Y as you
drive, park, open doors, turn lights on, etc. Monitor this area when driving as it displays important information such as
driving speed and warning messages (see Vehicle Status on page 1119). When in Park, you can interact with the vehicle and
open the powered frunk, tonneau, tailgate, and charge port door, and change the ride height setting. This area is also used
for shortcut cards for media, tire pressures, and trip information.
5. Controls: Control various features and customize CybertruckModel SModel XModel 3Model Y to suit your preferences.
The Controls screen appears over the map. Touch an option on the Controls screen to display the various settings and
preferences associated with the chosen option.
Owner's Manual

1113

Overview
To search for a specific setting, touch Search at the top of the Controls tab.
When an information icon displays beside a specific setting, touch to display a popup that provides helpful
details about the associated setting.

NOTE: Many vehicle controls, settings, and preferences (such as climate, media, and navigation) can be adjusted handsfree using voice commands (see Voice Commands on page 97).
6. Climate controls (driver): Use the left and right arrows to decrease/increase cabin temperature. Touch Split on the popup to
display separate controls for the driver and passenger. Touch the temperature icon to customize climate control settings
(see Operating Climate Controls on page 1338). The passenger climate controls display when temperature controls have
been Split to provide separate controls for the driver and passenger.
7. Map Orientation: Touch to toggle the orientation of the map between North Up and Heading Up (see Maps and Navigation
on page 699).
8. My Apps: For one-touch access to frequently used apps and controls, you can choose what displays here (see Customizing
My Apps on page 1118).
9. App Launcher: Touch the app launcher to open the app tray. Then touch any app to open it. The app you choose displays on
top of the map. To close an app, drag it downward or press the X in the corner of the app.
10. Recent App(s): Displays the most recently used app(s). The number of recent apps displayed here depends on how many
apps have been added to My Apps. If you add the maximum number of apps to My Apps, only the most recent app displays.
11. Volume Control: Controls the volume of media player and phone calls (see Volume Controls on page 708). The volume of
navigation instructions is controlled separately (see Maps and Navigation on page 699).

Top Status Bar Icons
Touch to lock/unlock all doors and closures.

4:20 pm

Your vehicle automatically updates the time. If the time is incorrect, confirm your vehicle has internet and GPS
connectivity with the latest software. To switch between 12 and 24 hour format, touch Controls > Display.
Displays on the touchscreen status bar only when CybertruckModel SModel XModel 3Model Y detects a
programmed myQ Smart Garage within range (see Smart Garage on page 365).

Displays on the touchscreen status bar only when CybertruckModel SModel XModel 3Model Y is parked. Add,
configure (including Valet Mode and Use Easy Entry), or quickly switch driver profiles. Driver profiles can also be
accessed from the top of any Controls screen (see Driver Profiles on page 514).

Available when CybertruckModel SModel XModel 3Model Y is parked, touch to manually enable or disable
Sentry Mode for the current drive cycle. To automatically turn Sentry Mode on (or off) every time you leave your
vehicle, enable the setting from Controls > Safety > Sentry Mode (see Sentry Mode on page 664).
NOTE: If you turn Sentry Mode on or off from Controls > Sentry Mode, the shortcuts on the vehicle's
touchscreen and mobile app will only work for the current drive cycle.

1114

Owner's Manual

Overview
Displays when CybertruckModel SModel XModel 3Model Y is connected to a Wi-Fi network.

Displays when CybertruckModel SModel XModel 3Model Y cellular connectivity is available or being used.

Appears when your vehicle's GPS location is actively being accessed in the Tesla app by the owner, an added
driver, or a third party app you're using. To disable, navigate to Controls > Safety > Allow Mobile Access on the
touchscreen.

Popup Messages and Vehicle Alerts
Popup messages appear at the bottom of the touchscreen. For example, a seat belt reminder appears if a seat belt is
unfastened in an occupied seat, an alert appears to notify you of an incoming phone call, and voice commands appear when in
use. If applicable, touch options from these popup messages (for example, accept/decline a phone call, choose an option from
the headlight menu, etc.). To dismiss a popup message, swipe it downward.

If an alert appears on your vehicle's touchscreen, touch Learn More for more details regarding the alert and how it can be
resolved (see Troubleshooting Alerts on page 952). You can view a list of vehicle alerts and notifications by touching the bell
icon at the top of Controls.
NOTE: Not all alerts provide additional information at this time.

Restarting the Touchscreen
You can restart your touchscreen if it is unresponsive or demonstrates unusual behavior.
WARNING: Only restart the touchscreen while the vehicle is stopped and in Park. The vehicle status display, safety
warnings, backup camera, etc. will not be visible during the restart.
1. Shift into Park.
2. Hold down both scroll buttons on the steering wheel until the touchscreen turns black.

Owner's Manual

1115

Overview

3. Wait approximately 30 seconds for the touchscreen to restart. If the touchscreen is still unresponsive or demonstrating
unusual behavior after a few minutes, try power cycling the vehicle, if possible (see Starting and Powering Off on page
373).
NOTE: Restarting the touchscreen also activates the drive mode selector on the overhead console.
NOTE: Pressing the scroll buttons only restarts the touchscreen. It does not restart any other vehicle component and does not
power CybertruckModel SModel XModel 3Model Y off and on.

1116

Owner's Manual

Overview
Rear Touchscreen

The rear touchscreen provides rear passengers with access to:
1. Fan Speed: Touch the arrows to decrease/increase the fan speed.
NOTE: You can also use the front touchscreen to adjust climate settings in the rear cabin (see Operating Climate Controls
on page 1338).
2. Power: Touch to turn the rear climate control system on or off.
3. Climate: Touch to turn the rear fan on or off and control the direction of air flow from the rear vents (see Adjusting the Front
and Rear Vents on page 1343).
4. Seats: Control rear seat heaters and move the front passenger seat forward/rearward using the arrows.
5. Media: Play, pause, skip or rewind through the currently playing song (see Media on page 707).
6. Video: Access video streaming services.
7. Arcade: Play various video games on the rear touchscreen.
8. Settings: Touch to pair up to two sets of Bluetooth headphones, change the brightness or clean the display.
NOTE: Connect headphones to listen to audio from the rear touchscreen. The vehicle supports up to two Bluetooth devices
at a time (such as one phone and one headset).
9. Volume: Touch the arrows to adjust the volume.
NOTE: Adjusting the media and volume controls also adjusts the front cabin settings.

Owner's Manual

1117

Overview
Rear Screen Remote Control
To control the rear screen from the front display, open the rear screen remote control app from the app
launcher. Besides audio, video and climate controls, you can lock the rear display in the app or by touching
Controls > Display > Lock Rear Display.

Customizing My Apps
For one-touch access to commonly used apps and controls, you can customize what displays in the My Apps area on the
touchscreen's bottom bar:
1. Enter customization mode by touching and holding any app or control in the My Apps area. If this area is empty, touch the
app launcher (the ellipsis icon).
2. Drag your desired app or control from the app tray onto the My Apps area in the bottom bar.
NOTE: Controls (for example, defrosters and seat heaters) appear in the app tray only when you enter customization mode
by touching and holding an app. Seat heaters selected from the app tray appear next to the temperature, instead of in the
My Apps area.
Remove an app or control from the My Apps area by touching and holding, then touching its associated "X".
When you've added the maximum number of apps or controls to My Apps, adding an additional app removes the rightmost
app.

Customizing Display and Sound Settings
Touch Controls > Display to adjust display settings to suit your preferences:
• Appearance: Customize the display to be Dark or Light. When set to Auto, the brightness changes automatically based on
ambient lighting conditions.
• Reduce Blue Light: When enabled, the display automatically adjusts to use warmer colors at night.
• Cybertruck Logo: When enabled, the display shows the CybertruckModel SModel XModel 3Model Y logo when it is
powered on. When disabled, the display shows the Tesla logo when it is powered on.
• Brightness: Drag the slider to manually control the brightness level. If Display Mode is set to Auto, the touchscreen further
adjusts based on both the ambient lighting conditions and your brightness preference. CybertruckModel SModel XModel
3Model Y remembers your chosen brightness preference and adjusts the touchscreen accordingly.
• Rear View Camera: Choose when to display the feed from the rear view camera. When set to Auto, the rear view camera
feed displays automatically when the tonneau cover is closed.
• Screen Clean Mode: When enabled, your touchscreen darkens and temporarily disables to facilitate cleaning. Follow the
onscreen instructions to exit Screen Clean Mode.
• Touchscreen Language: Select the language that the touchscreen displays.
NOTE: CybertruckModel SModel XModel 3Model Y must be in Park to change the language. When you change the
language, you experience a brief delay as the touchscreen restarts.
• Lock Rear Display: Lock access to the rear touchscreen.
• Time: Choose to display time in either 12 or 24 hour format.
• Energy Display: Choose to display remaining energy and charging units as either a percentage of battery energy remaining,
or as an estimate of the distance you can drive.
NOTE: When anticipating when you need to charge, use energy estimate as a general guideline only. Many factors have an
impact on energy consumption (see Getting Maximum Range on page 745).
• Distance: Choose to display range using miles or kilometers.

1118

Owner's Manual

Overview
• Temperature: Choose to display temperature using Fahrenheit or Celsius.
• Tire Pressure: Choose to display tire pressures using BAR or PSI.
In addition to customizing the display, you can enable Joe Mode to reduce the volume of all chimes that are not related to
critical safety issues. Touch Controls > Safety > Joe Mode to enable.

Naming your Vehicle
To further personalize your vehicle, you can name it. Touch Controls > Software > Name Your Vehicle located on the right side
of the touchscreen below the image of your CybertruckModel SModel XModel 3Model Y.
If your vehicle already has a name, touch the existing name to change it. Enter the new name in the popup and touch Save. The
name of your CybertruckModel SModel XModel 3Model Y appears in the Tesla mobile app, where you can also change it.

Erasing Personal Data
You can erase all personal data (saved addresses, music favorites, etc.) and restore all customized settings to their factory
defaults. This is useful when transferring ownership of CybertruckModel SModel XModel 3Model Y. Touch Controls > Service
> Factory Reset. Before erasing, CybertruckModel SModel XModel 3Model Y verifies your credentials by prompting you to
enter the user name and password associated with your Tesla account.

Vehicle Status
Overview
The touchscreen displays the status of CybertruckModel SModel XModel 3Model Y at all times. What you see depends on
whether the vehicle is:
• Parked (see Touchscreen on page 1112).
• Driving (see Driving Status on page 1123).
• Charging (see Charging Status on page 1371).
When CybertruckModel SModel XModel 3Model Y is parked, the status area shows the drive mode, estimated range,
suspension height and available adjustments, and an exterior view of the vehicle with buttons you can touch to open the
tonneau cover, tailgate, powered frunk, and charge port door.
When you press the brake pedal, CybertruckModel SModel XModel 3Model Y powers up and indicator lights flash briefly.
Unless an indicator light applies to the current situation (for example, a seat belt is not fastened), it should turn off. If an
indicator light fails to turn on or off, schedule a service appointment.
Cards
The bottom of the vehicle status display also shows shortcut "Cards" for quick access to Media, tire pressure data, trip
information, and more. Swipe the cards to the left or right to customize your cards shortcuts.
Indicator Lights
The following indicator lights illuminate to advise or alert you of a specific status or condition.
If the touchscreen displays this red brake indicator at any time other than briefly when you first start
CybertruckModel SModel XModel 3Model Y, a brake system fault is detected, or the level of the brake
fluid is low. Contact Tesla immediately. Apply steady pressure and keep the brake pedal firmly pressed to
stop the vehicle when safe to do so.
USA:

Owner's Manual

1119

Overview
Canada:

If the touchscreen displays this red brake indicator at any time other than briefly when you first start
CybertruckModel SModel XModel 3Model Y, a brake system fault is detected, or the level of the brake
fluid is low. Contact Tesla immediately. Apply steady pressure and keep the brake pedal firmly pressed
to stop the vehicle when safe to do so.

When you manually apply the parking brake using the touchscreen, the red parking brake indicator lights
up on the touchscreen.
USA:
When you manually apply the parking brake using the touchscreen, the red parking brake indicator
lights up on the touchscreen.
Canada:
If the parking brake experiences an electrical issue, the amber parking brake indicator lights up and a fault
message displays on the touchscreen.
USA:
If the parking brake experiences an electrical issue, the amber parking brake indicator lights up and a
fault message displays on the touchscreen.
Canada:
A seat belt for an occupied seat is not fastened. See Seat Belts on page 1157.

Airbag safety. If this indicator does not flash on briefly when CybertruckModel SModel XModel 3Model Y
prepares to drive, or if it remains on, contact Tesla immediately. See Airbag Status Indicator on page 1173.

A door or the powered frunk is open.

CybertruckModel SModel XModel 3Model Y detects a faulty electrical connection for the trailer lights. Some,
or all, trailer lights may not be functioning. Pull over as soon as safety permits and inspect the trailer lights for
faulty cabling or connections. If the issue is resolved and the red icon persists, manually turn Trailer Mode off
and on again. See Towing a Trailer on page 1258.
Tire pressure warning. The pressure of a tire is out of specification. If a fault with the Tire Pressure Monitoring
System (TPMS) is detected, the indicator flashes. For a TPMS fault, schedule a service appointment. See Tire
Pressures on page 1398.

1120

Owner's Manual

Overview
The tailgate is open. See Cargo Bed on page 1188.

The powered frunk is open. See Powered Frunk on page 1185.

This indicator flashes when the electronic stability control systems are actively minimizing wheel spin by
controlling brake pressure and motor power. See Traction Control on page 1239. If this indicator remains on, a
fault is detected and you should immediately contact Tesla.

Electronic stability control systems are no longer minimizing wheel spin. See Off-Road Driving on page 1249.

USA:
Canada:

The ABS indicator briefly flashes amber on the touchscreen when you first start
CybertruckModel SModel XModel 3Model Y. If this indicator lights up at any other time, an ABS fault has
occurred and the ABS is not operating. Contact Tesla. The braking system remains fully operational and is
not affected by an ABS failure. However, braking distances may increase. Drive cautiously and avoid heavy
braking.
The ABS indicator briefly flashes amber on the touchscreen when you first start
CybertruckModel SModel XModel 3Model Y. If this indicator lights up at any other time, an ABS fault has
occurred and the ABS is not operating. Contact Tesla. The braking system remains fully operational and
is not affected by an ABS failure. However, braking distances may increase. Drive cautiously and avoid
heavy braking.
The touchscreen displays this amber brake indicator if a brake booster fault is detected. Apply steady
pressure and keep the brake pedal firmly pressed to stop the vehicle when safe to do so. Hydraulic Boost
Compensation will be active (see Hydraulic Boost Compensation on page 1236).

USA:
The touchscreen displays this amber brake indicator if a brake booster fault is detected. Apply steady
pressure and keep the brake pedal firmly pressed to stop the vehicle when safe to do so. Hydraulic
Boost Compensation will be active (see Hydraulic Boost Compensation on page 1236).
Canada:
Vehicle power is currently being limited because the energy remaining in the Battery is low, the vehicle's
systems are being heated or cooled, or an error is detected by a drive inverter.

Rear fog lights are enabled. See Lights on page 1229.

Owner's Manual

1121

Overview
CybertruckModel SModel XModel 3Model Y detects a connection for trailer lights but Trailer Mode is
disabled. It is likely that a carrying accessory has been connected. See See Towing a Trailer on page 1258

Appears when regenerative braking is limited. See Regenerative Braking on page 1236 for more information.

Fog lights are enabled. See Lights on page 1229.

Parking lights are on (side marker lights, tail lights, and license plate lights). See Lights on page 1229.

Low beam headlights are on. See Lights on page 1229.

High beam headlights are on and Auto High Beam is disabled or currently unavailable. See Headlights on
page 1229.

Auto High Beam is enabled and high beams are on. CybertruckModel SModel XModel 3Model Y is ready to
turn off the high beams if needed. See Headlights on page 1229.

Trailer Mode is active. See Towing a Trailer on page 1258.

Some of the energy stored in the Battery may not be available due to cold weather conditions. In cold
weather, charging rates may also be limited. If CybertruckModel SModel XModel 3Model Y is plugged in,
you can heat your Battery by turning on climate control with the mobile app. This icon disappears when the
Battery is sufficiently warm.
Vehicle Hold is actively applying the brakes. See Vehicle Hold on page 1237.

Pedestrian Warning System is disabled. See Pedestrian Warning System on page 527.

1122

Owner's Manual

Overview
Auto High Beam is enabled but high beams are not on because another vehicle is detected in front of
CybertruckModel SModel XModel 3Model Y. When there is no longer another vehicle detected, high beams
automatically turn back on. See Headlights on page 1229.

See Popup Messages and Vehicle Alerts on page 1115 for more information about alert popups on your vehicle's touchscreen.

Driving Status
When CybertruckModel SModel XModel 3Model Y is driving (or ready to drive), the touchscreen shows your current driving
status and real-time visualization of the road as detected by the Autopilot components (see Cameras on page 1136). The
visualization automatically zooms in and out to better utilize touchscreen space and inform you when a vehicle is detected in
your blind spot.

The touchscreen also shows the following:
1. Total estimated driving distance (or energy) available. You can toggle between driving distance and percentage of Battery
energy remaining by touching the displayed value. You can also change how energy is displayed by touching Controls >
Display > Energy Display. When anticipating when you need to charge, use range estimates as a general guideline only.
2. Currently selected drive mode: Park, Reverse, Neutral, or Drive (see Shifting on page 405).
3. Driving speed.

Owner's Manual