546

Owner's Manual

Owners Manual
Autopilot Conditions
Ensure all cameras are clean and free of obstructions before each drive and before using Autopilot features (see Cleaning a
Camera on page 780Cleaning a Camera on page 780Cleaning a Camera on page 780Cleaning a Camera on page
781Cleaning a Camera on page 1139). Dirty cameras and sensors (if equipped), as well as environmental conditions such as
rain and faded lane markings, can affect Autopilot performance. If a camera is obstructed or blinded,
CybertruckModel SModel XModel 3Model Y displays a message on the instrument clustertouchscreen and Autopilot features
may not be available. For more information on specific alerts, see Troubleshooting Alerts on page 952Troubleshooting Alerts
on page 1008.
Before you can use Autopilot features, and after some Service visits, you must drive a short distance to calibrate cameras. For
more information, see Drive to Calibrate Cameras on page 108Drive to Calibrate Cameras on page 1139.
In addition, these features may not work as intended when:
• The road has sharp curves or significant changes in elevation.
• Road signs and signals are unclear, ambiguous, or poorly maintained.
• Visibility is poor (due to heavy rain, snow, hail, etc. or poorly lit roadways at night)
• You are driving in a tunnel or next to a highway divider that interferes with the view of the camera(s)
• Bright light (such as from oncoming headlights or direct sunlight) interferes with the view of the camera(s).
The list above does not represent an exhaustive list of situations that may interfere with proper operation of Autopilot features.
For more information, see Limitations and Warnings on page 627.
Autopilot
Feature
TrafficAware
Cruise
Control

Available When

• You are driving between 18 mph (30 km/h) and 90 mph (150 km/h)85 mph (140 km/h)
NOTE: You can activate Traffic-Aware Cruise Control at lower speeds if there is a vehicle detected at least
5 feet (1.5 meters) ahead of CybertruckModel SModel XModel 3Model Y.

Autosteer
• You are driving between 18 mph (30 km/h) and 90 mph (150 km/h)85 mph (140 km/h)
NOTE: You can activate Autosteer at lower speeds if there is a vehicle detected at least 5 feet (1.5 meters)
ahead of CybertruckModel SModel XModel 3Model Y.
NOTE: On a residential road, a road without a center divider, or a road that is not controlled access, the
maximum allowed cruising speed is limited and the instrument paneltouchscreen displays a message. The
restricted speed will be the speed limit of the road plus 5 mph (10 km/h).
• Headlights are set to On or Auto. Although Autopilot is available both during the day and in low light
conditions (dusk or dark), Autosteer aborts or is unavailable if headlights are set to Off. When Autosteer is
engaged, Auto High Beam Auto High Beam is automatically enabled (see High Beam Headlights on page
435High Beam Headlights on page 435High Beam Headlights on page 437 High Beam Headlights on page
422High Beam Headlights on page 422Headlights on page 1228) and the wiper iswipers are set to Auto.
Navigate on
Autopilot

• You are driving between 18 mph (30 km/h) and 90 mph (150 km/h)85 mph (140 km/h).
NOTE: You can activate Navigate on Autopilot at lower speeds if there is a vehicle detected at least 5 feet
(1.5 meters) ahead of CybertruckModel SModel XModel 3Model Y.
• You are driving on a controlled-access highway. When you leave a controlled-access highway, Navigate on
Autopilot reverts to Autosteer.

Owner's Manual

547

Owners Manual
Autopilot
Feature
Full SelfDriving
(Beta)

Available When

• You are driving less than 85 mph (150 km/h).
NOTE: You can activate Full Self-Driving (Beta) at lower speeds, including when
CybertruckModel SModel XModel 3Model Y is at a standstill, whether or not there is a vehicle detected in
front of CybertruckModel SModel XModel 3Model Y.
• Headlights are set to On or Auto. Although Full Self-Driving (Beta) is available both during the day and in
low light conditions (dusk or dark), it aborts or is unavailable if headlights are set to Off. When Full SelfDriving (Beta) is engaged, Auto High Beam is automatically enabled (see High Beam Headlights on page
435High Beam Headlights on page 435 High Beam Headlights on page 422High Beam Headlights on page
422Headlights on page 1228) and the wiper iswipers are set to Auto.

Autopilot Features
This topic describes how to enable and use the following driver assistance features.
• Traffic-Aware Cruise Control: Like traditional cruise control, Traffic-Aware Cruise Control maintains a set driving speed.
However, Traffic-Aware Cruise Control also slows down or accelerates CybertruckModel SModel XModel 3Model Y as
needed to maintain the following distance from the vehicle in front of you. While Traffic-Aware Cruise Control is engaged,
you are still responsible for steering CybertruckModel SModel XModel 3Model Y (see Traffic-Aware Cruise Control on
page 549).
• Autosteer: Like Traffic-Aware Cruise Control, Autosteer maintains a set speed (if there is not a vehicle in front of you) or a
set following distance (if there is a vehicle in front of you). In addition, Autosteer detects lane markings, road edges, and
the presence of vehicles and objects to intelligently keep CybertruckModel SModel XModel 3Model Y in its driving lane
(see Autosteer on page 551).
NOTE: Autosteer is a BETA feature.
• Auto Lane Change: When you engage a turn signal while Autosteer is active, Auto Lane Change moves
CybertruckModel SModel XModel 3Model Y into the adjacent lane in the direction indicated by the turn signal (see Auto
Lane Change on page 554).
• Navigate on Autopilot: Navigate on Autopilot builds on the features of Traffic-Aware Cruise Control and Autosteer. While
Autosteer is active, Navigate on Autopilot allows CybertruckModel SModel XModel 3Model Y to suggest and, if
configured, automatically change lanes to pass other vehicles and follow the navigation route (see Navigate on Autopilot on
page 556).
NOTE: Navigate on Autopilot is a BETA feature.
Traffic-Aware Cruise Control and Autosteer use information from the cameras on CybertruckModel SModel XModel 3Model Y
to detect lane markings, road edges, and other vehicles and road users around CybertruckModel SModel XModel 3Model Y.
CAUTION: Ensure all cameras are clean and free of obstructions before each drive and before using Autopilot features
(see Cleaning a Camera on page 780Cleaning a Camera on page 780Cleaning a Camera on page 780Cleaning a
Camera on page 781Cleaning a Camera on page 1139). Dirty cameras and sensors (if equipped), as well as
environmental conditions such as rain and faded lane markings, can affect Autopilot performance. If a camera is
obstructed or blinded, CybertruckModel SModel XModel 3Model Y displays a message on the instrument
clustertouchscreen and Autopilot features may not be available. For more information on specific alerts, see
Troubleshooting Alerts on page 952Troubleshooting Alerts on page 1008.
CAUTION: It is your responsibility to familiarize yourself with the limitations of Autopilot and the situations in which
driver intervention may be needed. For more information, see Limitations and Warnings on page 627.
Autopilot Settings
Before you use Autopilot features, customize how they work by touching Controls > Autopilot.
• Set Speed: Choose whether Autopilot engages at the currently detected speed limit or your current driving speed. Touch
Controls > Autopilot > Set Speed and choose either Speed Limit or Current Speed.
548

Owner's Manual

Owners Manual
• Offset: If you choose Speed Limit, you can specify an offset by touching Set Speed Offset. You can choose Fixed (the
cruising speed adjusts by a specific amount on all roads) or Percentage (the cruising speed is adjusted as a percentage of
the road's detected speed limit).
• Autopilot Activation: Choose how to activate Autosteer. If set to Single Click, both Traffic-Aware Cruise Control and
Autosteer engage when you single-press the right scroll wheel. If set to Double Click, you must double-press the right
scroll wheel to engage Autosteer.
NOTE: Autopilot Activation must be set to Double Click if you want to use Traffic-Aware Cruise Control independently of
Autosteer.
• Autopilot Activation: Choose how to activate Autosteer. If set to Single Click, both Traffic-Aware Cruise Control and
Autosteer engage when you single-press the right scroll wheel. If set to Double Click, you must double-press the right
scroll wheel to engage Autosteer.
NOTE: Autopilot Activation must be set to Double Click if you want to use Traffic-Aware Cruise Control independently of
Autosteer.
• Autopilot Activation: Choose how to activate Autosteer. If set to Single Pull, both Traffic-Aware Cruise Control and
Autosteer engage when you pull the drive stalk down once. If set to Double Pull, you must pull the drive stalk down twice in
quick succession to engage Autosteer.
NOTE: Autopilot Activation must be set to Double Pull if you want to use Traffic-Aware Cruise Control independently of
Autosteer.
• Autopilot Activation: Choose how to activate Autosteer. If set to Single Pull, both Traffic-Aware Cruise Control and
Autosteer engage when you pull the drive stalk down once. If set to Double Pull, you must pull the drive stalk down twice in
quick succession to engage Autosteer.
NOTE: Autopilot Activation must be set to Double Pull if you want to use Traffic-Aware Cruise Control independently of
Autosteer.
• Green Traffic Light Chime: In Canada and U.S.: If on, a chime will sound when you are waiting at a red traffic light and the
light turns green. If you are not actively using Traffic-Aware Cruise Control and are waiting at a red light with a car in front
of you, the chime sounds when the car ahead of you advances.
Traffic-Aware Cruise Control
Traffic-Aware Cruise Control is always enabled.
When Traffic-Aware Cruise Control is available but not engaged, the instrument clustertouchscreen displays
the cruising speed in gray. The number shown represents the speed that will be set when you engage TrafficAware Cruise Control.

When Traffic-Aware Cruise Control is actively cruising at a set speed, the speed is highlighted with blue text.

To engage Traffic-Aware Cruise Control, press the right scroll wheel, then release the accelerator pedal to allow Traffic-Aware
Cruise Control to maintain the cruising speed. You can apply the accelerator at any time to temporarily override the set
cruising speed.
NOTE: If Autopilot Activation is set to Single Click, pressing the right scroll wheel once also activates Autosteer (which
includes Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double Click to use
Traffic-Aware Cruise Control independently of Autosteer when you single-press the right scroll wheel.
To engage Traffic-Aware Cruise Control, press the right scroll wheel, then release the accelerator pedal to allow Traffic-Aware
Cruise Control to maintain the cruising speed. You can apply the accelerator at any time to temporarily override the set
cruising speed.
NOTE: If Autopilot Activation is set to Single Click, pressing the right scroll wheel once also activates Autosteer (which
includes Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double Click to use
Traffic-Aware Cruise Control independently of Autosteer when you single-press the right scroll wheel.

Owner's Manual

549

Owners Manual
To engage Traffic-Aware Cruise Control when it is available (the car status area of the touchscreen displays the gray cruising
speed icon), pull the drive stalk down once, then release the accelerator pedal to allow Traffic-Aware Cruise Control to
maintain the cruising speed. You can apply the accelerator at any time to temporarily override the set cruising speed.

NOTE: If Autopilot Activation is set to Single Pull, pulling the drive stalk down once also activates Autosteer (which includes
Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double Pull to use Traffic-Aware
Cruise Control independently of Autosteer when you pull the drive stalk down once.
To engage Traffic-Aware Cruise Control when it is available (the car status area of the touchscreen displays the gray cruising
speed icon), pull the drive stalk down once, then release the accelerator pedal to allow Traffic-Aware Cruise Control to
maintain the cruising speed. You can apply the accelerator at any time to temporarily override the set cruising speed.

NOTE: If Autopilot Activation is set to Single Pull, pulling the drive stalk down once also activates Autosteer (which includes
Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double Pull to use Traffic-Aware
Cruise Control independently of Autosteer when you pull the drive stalk down once.
If you want a chime to sound when you engage or cancel Traffic-Aware Cruise Control, touch Controls > Autopilot > TrafficAware Cruise Control Chime.
WARNING: Traffic-Aware Cruise Control is designed for your driving comfort and convenience and is not a collision
warning or avoidance system. It is your responsibility to stay alert, drive safely, and be in control of the vehicle at all
times. Never depend on Traffic-Aware Cruise Control to adequately slow down CybertruckModel SModel XModel
3Model Y. Always watch the road in front of you and be prepared to take corrective action at all times. Failure to do so
can result in serious injury or death. For more information, see Limitations and Warnings on page 627.

550

Owner's Manual

Owners Manual
Autosteer
To enable Autosteer:
1. Touch Controls > Autopilot > Autopilot Features > Autosteer (Beta).
2. After carefully reading and understanding the popup window, touch Yes.
To indicate that Autosteer is available (but not actively steering
CybertruckModel SModel XModel 3Model Y), the instrument paneltop corner of the
touchscreen displays a gray Autosteer icon next to the driving gear. In situations where
Autosteer is temporarily unavailable, the Autosteer icon disappears. (For example, if your
driving speed is not within the speed required for Autosteer to operate.)

To initiate Autosteer, press the right scroll wheelpress the right scroll wheelmove the drive stalk fully down twice in quick
successionmove the drive stalk fully down twice in quick succession.
NOTE: If the setting for Autopilot Activation is set to Double Click, you must double-press the right scroll wheel to engage
Autosteer (see Autopilot Settings on page 548).
NOTE: If the setting for Autopilot Activation is set to Double Click, you must double-press the right scroll wheel to engage
Autosteer (see Autopilot Settings on page 548).
NOTE: If the setting for Autopilot Activation is set to Single Pull, pulling the drive stalk down once engages Autosteer (see
Autopilot Settings on page 548).
NOTE: If the setting for Autopilot Activation is set to Single Pull, pulling the drive stalk down once engages Autosteer (see
Autopilot Settings on page 548).

Owner's Manual

551

Owners Manual

Autosteer confirms activation with an audible chime and briefly displays a message on the instrument clustertouchscreen
reminding you to pay attention to the road and be ready to take over at any time.
To indicate that Autosteer is now active, the instrument clustertouchscreen displays
the Autosteer icon in blue.

When Autosteer is able to detect lane markings, it displays the edges of the driving lane in blue on the instrument
clustertouchscreen.

552

Owner's Manual

Owners Manual

Owner's Manual

553

Owners Manual

Whenever Autosteer is active, Traffic-Aware Cruise Control is active as well.
In situations where the speed limit cannot be detected when Autosteer is engaged, Autosteer reduces your driving speed and
limits the set cruising speed to 45 mph (70 km/h). Although you can manually accelerate to exceed the limited speed,
CybertruckModel SModel XModel 3Model Y will not brake for detected obstacles as long as you are applying the accelerator
pedal. Autosteer slows down to the limited speed when you release the accelerator pedal. When you leave the road or
disengage Autosteer by using the steering wheelsteering yoke (or steering wheel), you can increase your set speed again, if
desired.
WARNING: Steering is limited when Autosteer is enabled. Therefore, CybertruckModel SModel XModel 3Model Y may
not be able to handle tight turns. Be prepared to take control of the vehicle at all times.
WARNING: Autosteer is a hands-on assistance feature. Keep your hands on the steering wheelsteering yoke (or steering
wheel) at all times, be mindful of road conditions and surrounding traffic, and always be prepared to take immediate
action. Failure to follow these instructions could cause damage, serious injury or death. It is your responsibility to
familiarize yourself with the limitations of Autosteer and the situations in which it may not work as expected. For more
information, see Limitations and Warnings on page 627.
Auto Lane Change
If you engage a turn signal while Autosteer is active, CybertruckModel SModel XModel 3Model Y moves into the adjacent lane
in the direction indicated by the turn signal, provided the following conditions are met:
• The turn signal is engaged.
• Lane markings indicate that a lane change is permitted.
• Midway through the lane change, CybertruckModel SModel XModel 3Model Y must detect the target lane's outside lane
marking. If this lane marking is not detected, the lane change is aborted and CybertruckModel SModel XModel 3Model Y
returns to its original driving lane.
• The view of the camera(s) is not obstructed.
• CybertruckModel SModel XModel 3Model Y does not detect a vehicle in its blind spot, or a vehicle or obstacle up to the
center of the target lane. If a vehicle or other obstacle is detected in the target lane, it is shown in red in the visualization on
the instrument clustertouchscreen and CybertruckModel SModel XModel 3Model Y does not complete the lane change
until it is safe to do so.

554

Owner's Manual

Owners Manual

NOTE: Auto Lane Change cancels if the lane change cannot be completed in 5 seconds.
WARNING: Although Autopilot is designed to detect vehicles and obstacles in adjacent lanes, it is your responsibility to
always perform visual checks to make sure it is safe and appropriate to move into the target lane. If Autopilot cannot
change lanes due to inadequate data, the instrument clustertouchscreen displays a series of warnings. Therefore, when
using Auto Lane Change, always pay attention to the instrument clustertouchscreen and be prepared to manually steer
CybertruckModel SModel XModel 3Model Y.
The minimum speed at which Autopilot changes lanes may vary depending on region, adjacent lane speeds, and other factors.
Always be ready to manually steer and change lanes as necessary. When an automatic lane change is in progress, Overtake
Acceleration is activated, allowing CybertruckModel SModel XModel 3Model Y to accelerate closer to a vehicle in front (see
Overtake Acceleration on page 568).
When you engage a turn signal, Autopilot moves CybertruckModel SModel XModel 3Model Y one lane at a time. Moving into
an additional lane requires you to engage the turn signal a second time after the first lane change is complete.
As CybertruckModel SModel XModel 3Model Y changes lanes, it is important to monitor its performance by watching the
driving path in front of you and the surrounding area. Stay prepared to take over steering at any time. As you are crossing over
into the adjacent lane, the instrument clustertouchscreen displays the location in the lane that
CybertruckModel SModel XModel 3Model Y is moving into.

Owner's Manual

555

Owners Manual

Navigate on Autopilot
To enable Navigate on Autopilot, touch Controls > Autopilot > Navigate on Autopilot (Beta). Then, to customize how you want
Navigate on Autopilot to operate, touch Customize Navigate on Autopilot:
• Enable at Start of Every Trip: Choose whether to automatically enable Navigate on Autopilot for every navigation route.
When enabled, the Navigate on Autopilot button on the turn-by-turn direction list is already enabled at the start of every
trip.
• Speed Based Lane Changes: Navigate on Autopilot is designed to perform both route-based and speed-based lane
changes. Speed-based lanes changes are optional. You can use this setting to disable speed-based lane changes or to
specify how assertively you want Navigate on Autopilot to change lanes to achieve the set cruising speed (Mild, Average, or
Mad Max).
• Exit Passing Lane: Choose whether you want Navigate on Autopilot to maneuver out of a passing lane when navigating to a
destination. In addition to route-based and speed-based lane changes, Navigate on Autopilot requests a lane change out
of a passing lane as a reminder to stay in a slower lane when you are not passing other vehicles. Choose No to disable this
and keep CybertruckModel SModel XModel 3Model Y in a passing lane except when needed to stay on the navigation
route.
• Require Lane Change Confirmation: By default, Navigate on Autopilot requires your confirmation before proceeding with a
lane change by pressing the appropriate turn signalengaging the appropriate turn signal. If you do not confirm the lane
change within 3 seconds, a chime sounds to remind you that Navigate on Autopilot requires your confirmation to change
lanes.
• Lane Change Notification: You can specify if or how you want to be notified of lane changes (Off, Chime, Vibrate, or Both).
If Enable at Start of Every Trip is turned on, Navigate on Autopilot engages automatically when:
• Autosteer is active.
• You are navigating to a destination.
556

Owner's Manual

Owners Manual
• You are on a controlled-access highway.
Once enabled, the Navigate on Autopilot button appears on the map’s turn-by-turn direction list whenever a navigation route
is active and the route includes at least one controlled-access highway.
If Enable at Start of Every Trip is turned off, touch the Navigate on Autopilot button above the turn-by-turn directions to enable
it. Once the Navigate on Autopilot is selected, it will engage whenever you engage Autosteer.
The Navigate on Autopilot icon shows in the turn-by-turn direction list when you are navigating to
a destination and Navigate on Autopilot is available but not active.

If Navigate on Autopilot is active, the icon is blue. If Enable at Start of Every Trip is turned on, the
Navigate on Autopilot icon is selected whenever you start navigation. Touch the icon to cancel
Navigate on Autopilot and revert to Autosteer.

Whenever Navigate on Autopilot is active, the Navigate on Autopilot button is blue and the instrument clustertouchscreen
displays the driving lane as a single blue line in front of CybertruckModel SModel XModel 3Model Y:

Owner's Manual

557

Owners Manual

The turn-by-turn directions display the Autosteer icon next to the maneuvers (such as off-ramps) that Navigate on Autopilot
will handle.
When Navigate on Autopilot is engaged CybertruckModel SModel XModel 3Model Y automatically makes both speed-based
and route-based lane changes after driver confirmation.
• Speed Based Lane Changes: Navigate on Autopilot changes lanes to reduce driving time to your destination. For example, if
CybertruckModel SModel XModel 3Model Y is behind a vehicle going below the set cruising speed, Navigate on Autopilot
will move into the passing lane to pass it. Speed-based lanes changes are optional.
• Route Based Lane Changes: Navigate on Autopilot changes lanes to route you to your destination. For example, Navigate on
Autopilot will move into the exit lane as CybertruckModel SModel XModel 3Model Y approaches the off-ramp specified by
the navigation route.
When the instrument clustertouchscreen displays a message asking you to confirm the lane change, engage the appropriate
turn signal. If you do not confirm the lane change within 3 seconds, a chime sounds to remind you that Navigate on Autopilot
requires your confirmation to change lanes. Auto Lane Change cancels if the lane change cannot be completed in 5 seconds.
If you ignore a route-based lane change suggestion (for example, you are driving in the left lane while approaching an offramp on the right side of the highway), Navigate on Autopilot is unable to maneuver onto the off-ramp and as a result, you are
re-routed to your destination.

558

Owner's Manual

Owners Manual
NOTE: When determining navigation routes, and maneuvers at interchanges, Navigate on Autopilot considers whether or not
you want to use High Occupancy Vehicle (HOV) lanes. Therefore, ensure the Use HOV Lanes setting is appropriate for your
circumstances (see Maps and Navigation on page 700). If the setting is off, Navigate on Autopilot never uses a HOV lane,
regardless of time of day. If the setting is on, Navigate on Autopilot uses HOV lanes, whenever applicable.
CAUTION: Navigate on Autopilot may not always attempt to exit at an off-ramp or change lanes, even when an exit or
lane change is determined by the navigation route. Always remain alert and be prepared to manually steer onto an offramp, or make a lane change to prepare for, or to exit at, an off-ramp or interchange.
Navigate on Autopilot activates and deactivates based on the type of road you are driving on. When Navigate on Autopilot is
active and you approach an off-ramp or interchange along your navigation route, the appropriate turn signal engages and
Autosteer maneuvers CybertruckModel SModel XModel 3Model Y onto the off-ramp or interchange.
When you leave a controlled-access highway Navigate on Autopilot reverts to Autosteer—a chime sounds and the instrument
clustertouchscreen displays the driving lane lines in blue (instead of the single blue in front of
CybertruckModel SModel XModel 3Model Y). When Navigate on Autopilot deactivates, Autosteer remains active. Always be
prepared to take appropriate action.
WARNING: Navigate on Autopilot is a hands-on feature. Keep your hands on the steering wheelsteering yoke (or
steering wheel) at all times, be mindful of road conditions and surrounding traffic, and always be prepared to take
immediate action. Failure to follow these instructions could cause damage, serious injury or death. It is your
responsibility to familiarize yourself with the limitations of Navigate on Autopilot and the situations in which it may not
work as expected. For more information, see Limitations and Warnings on page 627.
Canceling Autopilot
Traffic-Aware Cruise Control cancels when:
• You move the drive stalk upward.
◦ CAUTION: If you move the drive stalk upward and hold it up for more than one second,
CybertruckModel SModel XModel 3Model Y shifts into Neutral after canceling Autosteer.
• You move the drive stalk upward.
◦ CAUTION: If you move the drive stalk upward and hold it up for more than one second,
CybertruckModel SModel XModel 3Model Y shifts into Neutral after canceling Autosteer.
• You press the right scroll wheel on the steering wheelsteering yoke (or steering wheel).
• You press the right scroll wheel on the steering wheelsteering yoke (or steering wheel).
• You press the brake pedal.
• You exceed 90 mph (150 km/h).
• You shift into Reverse, Park, or Neutral.
• A door is opened.
• An Automatic Emergency Braking event occurs (see Collision Avoidance Assist on page 641).
• The driver's seatbelt is released, and/or the driver gets out of their seat.

Owner's Manual

559

Owners Manual

When Traffic-Aware Cruise Control cancels, the cruising speed icon on the instrument clustertouchscreen turns gray to
indicate that Traffic-Aware Cruise Control is no longer active.
Autosteer cancels when any of the above actions are taken. In addition, Autosteer cancels when:
• You exceed 85 mph (140 km/h).
• You take over steering manually.You apply rotational force to the steering wheelsteering yoke (or steering wheel) (even a
slight amount).
WARNING: If Autopilot Activation is set to Double Click and Autosteer cancels because you started steering
manuallyapplied rotational force to the steering wheelsteering yoke (or steering wheel), Traffic-Aware Cruise Control
remains active. If Autopilot Activation is set to Single Click and Autosteer cancels because you started steering
manuallyapplied rotational force to the steering wheelsteering yoke (or steering wheel), Traffic-Aware Cruise Control
also cancels.
WARNING: If Autopilot Activation is set to Double Click and Autosteer cancels because you started steering
manuallyapplied rotational force to the steering wheel, Traffic-Aware Cruise Control remains active. If Autopilot
Activation is set to Single Click and Autosteer cancels because you started steering manuallyapplied rotational force
to the steering wheel, Traffic-Aware Cruise Control also cancels.
WARNING: If Autopilot Activation is set to Double Pull and Autosteer cancels because you started steering
manuallyapplied rotational force to the steering wheel, Traffic-Aware Cruise Control remains active. If Autopilot
Activation is set to Single Pull and Autosteer cancels because you started steering manuallyapplied rotational force
to the steering wheel, Traffic-Aware Cruise Control also cancels.

560

Owner's Manual

Owners Manual
WARNING: If Autopilot Activation is set to Double Pull and Autosteer cancels because you started steering
manuallyapplied rotational force to the steering wheel, Traffic-Aware Cruise Control remains active. If Autopilot
Activation is set to Single Pull and Autosteer cancels because you started steering manuallyapplied rotational force
to the steering wheel, Traffic-Aware Cruise Control also cancels.
• You do not respond to repeated reminders to keep your hands on the wheel and subsequent messages on the instrument
clustertouchscreen (see Driver Attentiveness on page 569).
When Autosteer cancels, a chime sounds and the Autosteer icon either turns gray to indicate that Autosteer is no longer
active, or disappears to indicate that it is not currently available.
Navigate on Autopilot cancels when Autosteer cancels, as described above. In addition, Navigate on Autopilot cancels when:
• You touch the Navigate on Autopilot button on the map’s turn-by-turn direction list. In this case, Autosteer is still active.
• You leave a controlled-access highway. When this happens, Autosteer is still active.
When Navigate on Autopilot cancels but Autosteer remains active, a chime sounds and the visualization goes from a single
blue line in the driving lane to two blue lines on either side of the lane.
When Traffic-Aware Cruise Control or Autosteer cancels, CybertruckModel SModel XModel 3Model Y does not coast.
Instead, regenerative braking slows down CybertruckModel SModel XModel 3Model Y in the same way as when you move
your foot off the accelerator when driving without Traffic-Aware Cruise Control (see Regenerative Braking on page 463).
While Using Autopilot
When Traffic-Aware Cruise Control is active and Autopilot is maintaining a set speed, the speed is highlighted with blue text
on the instrument clustertouchscreen.
When Autosteer is active, the steering wheelsteering yoke (or steering wheel) icon is blue and the lane markings are
highlighted in blue on the visualization. If Navigate on Autopilot is also active, the Navigate on Autopilot button is blue and the
instrument clustertouchscreen displays the driving lane as a single blue line in front of CybertruckModel SModel XModel
3Model Y.
To display more details about the roadway and its surroundings, such as road markings, stop lights, and objects (such as trash
cans and poles), touch Controls > Autopilot > Full Self-Driving Visualization Preview.
If unable to detect lane markings, Autosteer may determine the driving lane based on a vehicle you are following. In most
cases, Autosteer attempts to center CybertruckModel SModel XModel 3Model Y in the driving lane. However, there may be
situations in which Autosteer follows a driving path that is offset from the center of the lane (for example, if guard rails are
detected).

Maintaining the Set Speed
When Autopilot is active, CybertruckModel SModel XModel 3Model Y maintains your set cruising speed whenever a vehicle is
not detected in front of it. When cruising behind a vehicle, CybertruckModel SModel XModel 3Model Y accelerates and
decelerates as needed to maintain a chosen following distance (see Adjusting the Following Distance on page 564), up to the
set speed.
You can manually accelerate at any time by pressing the accelerator pedal, but when you release the pedal
CybertruckModel SModel XModel 3Model Y resumes cruising at the set speed.
CybertruckModel SModel XModel 3Model Y also adjusts the cruising speed when entering and exiting curves.
When CybertruckModel SModel XModel 3Model Y is actively slowing down to maintain the selected distance from the vehicle
ahead, brake lights turn on. You may notice slight movement of the brake pedal. However, when
CybertruckModel SModel XModel 3Model Y is accelerating, the accelerator pedal does not move.

Changing the Set Speed
Roll the right scroll wheel up to increase, or down to decrease, the set speed.
You can also change the cruising speed to the current speed limit (including any offset you've specified), by either:
Owner's Manual

561

Owners Manual
You can also change the cruising speed to the current speed limit (including any offset you've specified), by either:
• Pushing the drive stalk downward and briefly holding.
• Touching and briefly holding the speed limit sign on the touchscreen until you see the cruising speed change.
• Pushing the drive stalk downward and briefly holding.
• Touching and briefly holding the speed limit sign on the touchscreen until you see the cruising speed change.

562

Owner's Manual

Owners Manual

Owner's Manual

563

Owners Manual

It may take a few seconds for CybertruckModel SModel XModel 3Model Y to reach the new cruising speed.

Adjusting the Following Distance
To adjust the following distance you want to maintain between CybertruckModel SModel XModel 3Model Y and a vehicle
traveling ahead of you, press the steering wheel's right scroll button to the left or right.
NOTE: If Full Self-Driving (Beta) is active, pressing the steering wheel's right scroll button to the left or right changes the Full
Self-Driving (Beta) profile (see Full Self-Driving (Beta) on page 598).
To adjust the following distance you want to maintain between CybertruckModel SModel XModel 3Model Y and a vehicle
traveling ahead of you, touch Controls > Autopilot > Cruise Follow Distance.
To adjust the following distance you want to maintain between CybertruckModel SModel XModel 3Model Y and a vehicle
traveling ahead of you, touch Controls > Autopilot > Cruise Follow Distance or press the right scroll button on the steering
wheel to the left or right.

564

Owner's Manual

Owners Manual

The closest following distance is 2.The closest following distance is 1.

Owner's Manual

565

Owners Manual

Each setting corresponds to a time-based distance that represents how long it takes for CybertruckModel SModel XModel
3Model Y, from its current location, to reach the location of the rear bumper of the vehicle ahead of you. Autopilot retains your
setting until you change it again.
As you adjust the following distance, the touchscreen displays the current setting.
As you adjust the following distance, the touchscreen displays the current setting.

Stopping and Slowdowns
When moving significantly faster than vehicles in adjacent lanes, CybertruckModel SModel XModel 3Model Y automatically
reduces the driving speed. This is especially helpful in heavy traffic situations or when vehicles are constantly merging into
different lanes. When CybertruckModel SModel XModel 3Model Y detects other vehicles driving significantly slower, the
instrument clustertouchscreen highlights the adjacent lanes with arrows and detected vehicles in gray, and
CybertruckModel SModel XModel 3Model Y reduces the driving speed as appropriate. To temporarily override this feature,
press the accelerator pedal.

566

Owner's Manual

Owners Manual

When following a vehicle, Autopilot remains active at low speeds, even when CybertruckModel SModel XModel 3Model Y
comes to a full stop. For example, Autopilot remains active even if CybertruckModel SModel XModel 3Model Y slows down to
a complete or near-complete stop in heavy, stop-and-go traffic on a highway. When traffic starts moving more rapidly,
Autopilot again accelerates up to the set speed.
Sometimes when CybertruckModel SModel XModel 3Model Y is at a full stop, Autopilot goes into a HOLD state. If this
happens, briefly press the accelerator pedal to resume cruising.
When the HOLD status is active, the instrument clustertouchscreen displays the HOLD icon and a message that
indicates that you need to resume cruise control.

CybertruckModel SModel XModel 3Model Y goes into HOLD state while Autopilot is active in the following circumstances:
• CybertruckModel SModel XModel 3Model Y has been at a standstill for 5 minutes.
• CybertruckModel SModel XModel 3Model Y detects a pedestrian (the HOLD state may clear when the pedestrian is no
longer detected).
• CybertruckModel SModel XModel 3Model Y suddenly loses visibility of the vehicle in front of you.
• An obstacle is detected in front of CybertruckModel SModel XModel 3Model Y.

Cruising Near or On Exits
When you are cruising near an exit on a controlled-access highway and engage the turn signal toward the off-ramp, Autopilot
assumes you are exiting and begins to slow down CybertruckModel SModel XModel 3Model Y. If you do not drive onto the
off-ramp, Autopilot resumes cruising at the set speed.
In a region with right hand traffic, this occurs only when you engage the right turn signal when driving in the right-most lane
within 164 ft. (50 meters) of an exit. Likewise in regions with left hand traffic, this occurs when engaging the left turn signal
when driving in the left-most lane within 164 ft. (50 meters) of an exit.
NOTE: If Navigate on Autopilot is active, CybertruckModel SModel XModel 3Model Y will perform a route-based lane change
to enter the exit lane and take the off-ramp as necessary to follow the navigation route.

Owner's Manual

567

Owners Manual
When enabled while on a highway interchange or off-ramp, Traffic-Aware Cruise Control may reduce your set speed in 5 mph
(5 km/h) increments – to as slow as 25 mph (40 km/h) – to better match the reported speeds of other Tesla vehicles that have
driven at that specific location. To override this and continue cruising at your set speed, tap the accelerator pedal. The new set
speed is maintained for the duration of the interchange or off-ramp (unless you override it or cancel Autopilot). After the
interchange or off-ramp, the set speed may revert or change as necessary based on the new location. For example, if you
merged onto a different highway, the set cruising speed reverts to what it was before driving on the interchange.
WARNING: In some cases (such as having insufficient data), Traffic-Aware Cruise Control may not automatically reduce
the set speed on the highway interchange or off-ramp. Do not rely on Traffic-Aware Cruise Control to determine an
appropriate driving speed. Tesla recommends driving at a speed that is safe for road conditions and within posted speed
limits.
When cruising onto an on-ramp to a controlled-access highway, Autopilot automatically adjusts the set cruising speed to the
speed limit of the highway, plus any offset you have specified. If Navigate on Autopilot is engaged, it disengages as you leave
the controlled-access highway (see Canceling Autopilot on page 559). In this case, Autosteer remains active.

Overtake Acceleration
Engage the turn signal momentarily to accelerate CybertruckModel SModel XModel 3Model Y towards the vehicle ahead of it.
By momentarily holding the turn signal stalk up or down stalk up or down, you can quickly accelerate up to your set speed
without having to press the accelerator pedal as long as:
• Traffic-Aware Cruise Control is operating and detects a vehicle in front of you.