NHTSA ID Number: 11001927
Manufacturer Communication Number: 2024.14_0524.pdf
TSB/Document Date: 2024-06-20
Summary
Tesla
does not provide physical owner's manual copies. Instead, all available owner’s manual content is integrated into the vehicle software, and only the content relevant for a given vehicle, based on vehicle configuration and software version installed, is displayed on its touchscreen. This file contains all available owner’s manual content for the vehicle converted to PDF format, and given the distribution method and NHTSA’s submission format requirements, it is the best available representative copy of owner’s manual content. However, a customer who accesses the owner’s manual via their vehicle’s touchscreen would only see the parts of this PDF file that are relevant to their vehicle.
Cruise Control is active, you must push the drive stalk up to the first position and hold it there for more than 1 second. In
doing so, Autosteer or Traffic-Aware Cruise Control is disabled.
• When in Reverse, shift into Neutral by briefly pushing the drive stalk down to the first position.
NOTE: You must press the brake pedal to shift out of Neutral if driving slower than approximately 5 mph (8 km/h).
CybertruckModel SModel XModel 3Model Y automatically shifts into Park when you leave the driver's seat. To stay in Neutral,
use the touchscreen to engage Transport Mode (see Instructions for Transporters on page 921).
If CybertruckModel SModel XModel 3Model Y is in Park and you use the touchscreen to release the parking brake (Controls >
Safety > Parking Brake), CybertruckModel SModel XModel 3Model Y shifts into Neutral (see Parking Brake on page 467).
Drive
Push the drive stalk all the way down and release. You can shift into Drive when CybertruckModel SModel XModel 3Model Y is
stopped or moving less than 5 mph (8 km/h) in Reverse.
NOTE: When in Drive, push the drive stalk all the way down and release to enable cruise control (see Cruise Control on page
477).
NOTE: When in Drive, push the drive stalk all the way down once to engage Traffic-Aware Cruise Control, or twice in quick
succession to engage Autosteer. If Autopilot Activation is set to Single Pull, pulling the drive stalk down once activates
Autosteer (which includes Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double
Pull to use Traffic-Aware Cruise Control independently of Autosteer when you pull the drive stalk down once. For more
information, see Autopilot Settings on page 548.
Park
Press the end of the drive stalk while CybertruckModel SModel XModel 3Model Y is stopped.
CybertruckModel SModel XModel 3Model Y automatically shifts into Park to prevent roll-away while driving in low speeds.
This happens whenever you connect a charge cable, unbuckle your seat belt, or open the door while in Drive or Neutral.
Ensure the charge cable is removed, buckle your seat belt, and close the door before shifting out of Park.
Attempting to engage the parking brake above 5 mph (8 km/h) will result in emergency braking (see Emergency Braking on
page 461).
To make it convenient to pick up passengers, you can also unlock all doors and/or extend the door handles at any time by
shifting into Park then pressing the Park button a second time.
NOTE: You must press the brake pedal to shift out of Park.
NOTE: The above conditions do not reflect a comprehensive list of reasons why CybertruckModel SModel XModel 3Model Y
may or may not automatically shift into Park and, in certain scenarios, it is possible for your vehicle to shift into Park when only
one of the above conditions is true.
400
Owner's Manual
Owners Manual
CAUTION: CybertruckModel SModel XModel 3Model Y will not shift out of Park if the front trunk is not securely shut or
if the charge port is unable to determine whether a charging cable is plugged in. Ensure the front trunk is closed and any
charging cables are unplugged, and follow the directions on the touchscreen to proceed.
CAUTION: In emergency situations, if the brakes are not functioning properly, press and hold the Park button on the
center console or touchscreenon the drive stalk to bring CybertruckModel SModel XModel 3Model Y to a stop. Do not
use this method to stop the vehicle unless absolutely necessary.
WARNING: It is the driver's responsibility to always ensure the vehicle is in Park before exiting. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically shift into Park for you; it might not work in all
circumstances (for example, if Creep or a slope causes the vehicle to travel greater than approximately 1.5 mph (2 km/
h)).
Owner's Manual
401
Owners Manual
Shifting
How to Shift
When CybertruckModel SModel XModel 3Model Y is in Park, you must press the brake pedal to shift.
Move the drive stalk up or down to shift into different drive modes.
If you try to shift when it is prohibited by the current driving speed, a chime sounds and the drive mode does not change.
Reverse
Push the drive stalk all the way up and release. You can only shift into Reverse when CybertruckModel SModel XModel
3Model Y is stopped or moving less than 5 mph (8 km/h).
Neutral
Neutral allows CybertruckModel SModel XModel 3Model Y to roll freely when you are not pressing the brake pedal:
• When in Park, shift into Neutral by briefly pushing the drive stalk either up or down to the first position.
402
Owner's Manual
Owners Manual
• When in Drive, shift into Neutral by briefly pushing the drive stalk up to the first position. If Autosteer or Traffic-Aware
Cruise Control is active, you must push the drive stalk up to the first position and hold it there for more than 1 second. In
doing so, Autosteer or Traffic-Aware Cruise Control is disabled.
• When in Reverse, shift into Neutral by briefly pushing the drive stalk down to the first position.
NOTE: You must press the brake pedal to shift out of Neutral if driving slower than approximately 5 mph (8 km/h).
CybertruckModel SModel XModel 3Model Y automatically shifts into Park when you leave the driver's seat. To stay in Neutral,
use the touchscreen to engage Transport Mode (see Instructions for Transporters on page 921).
If CybertruckModel SModel XModel 3Model Y is in Park and you use the touchscreen to release the parking brake (Controls >
Safety > Parking Brake), CybertruckModel SModel XModel 3Model Y shifts into Neutral (see Parking Brake on page 467).
Drive
Push the drive stalk all the way down and release. You can shift into Drive when CybertruckModel SModel XModel 3Model Y is
stopped or moving less than 5 mph (8 km/h) in Reverse.
NOTE: When in Drive, push the drive stalk all the way down and release to enable cruise control (see Cruise Control on page
477).
NOTE: When in Drive, push the drive stalk all the way down once to engage Traffic-Aware Cruise Control, or twice in quick
succession to engage Autosteer. If Autopilot Activation is set to Single Pull, pulling the drive stalk down once activates
Autosteer (which includes Traffic-Aware Cruise Control). Touch Controls > Autopilot > Autopilot Activation and choose Double
Pull to use Traffic-Aware Cruise Control independently of Autosteer when you pull the drive stalk down once. For more
information, see Autopilot Settings on page 548.
Park
Press the end of the drive stalk while CybertruckModel SModel XModel 3Model Y is stopped.
CybertruckModel SModel XModel 3Model Y automatically shifts into Park to prevent roll-away while driving in low speeds.
This happens whenever you connect a charge cable, unbuckle your seat belt, or open the door while in Drive or Neutral.
Ensure the charge cable is removed, buckle your seat belt, and close the door before shifting out of Park.
Attempting to engage the parking brake above 5 mph (8 km/h) will result in emergency braking (see Emergency Braking on
page 461).
To make it convenient to pick up passengers, you can also unlock all doors and/or extend the door handles at any time by
shifting into Park then pressing the Park button a second time.
NOTE: You must press the brake pedal to shift out of Park.
NOTE: The above conditions do not reflect a comprehensive list of reasons why CybertruckModel SModel XModel 3Model Y
may or may not automatically shift into Park and, in certain scenarios, it is possible for your vehicle to shift into Park when only
one of the above conditions is true.
Owner's Manual
403
Owners Manual
CAUTION: CybertruckModel SModel XModel 3Model Y will not shift out of Park if the front trunk is not securely shut or
if the charge port is unable to determine whether a charging cable is plugged in. Ensure the front trunk is closed and any
charging cables are unplugged, and follow the directions on the touchscreen to proceed.
CAUTION: In emergency situations, if the brakes are not functioning properly, press and hold the Park button on the
center console or touchscreenon the drive stalk to bring CybertruckModel SModel XModel 3Model Y to a stop. Do not
use this method to stop the vehicle unless absolutely necessary.
WARNING: It is the driver's responsibility to always ensure the vehicle is in Park before exiting. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically shift into Park for you; it might not work in all
circumstances (for example, if Creep or a slope causes the vehicle to travel greater than approximately 1.5 mph (2 km/
h)).
404
Owner's Manual
Owners Manual
Shifting
Shift Using the Touchscreen
When you press the brake pedal when parked, the drive mode strip displays on one side of the touchscreen. Use the drive
mode strip to shift CybertruckModel SModel XModel 3Model Y: swipe up for Drive, swipe down for Reverse or touch the P for
Park or N for Neutral. The drive mode strip is always available on the touchscreen when you touch Controls.Swipe from the
edge of the touchscreen towards the passenger to bring up the drive mode strip.
NOTE: To shift from Drive into Reverse or vice versa, the driving speed must be less than 5 mph (8 km/h).
The touchscreen's drive mode strip displays Park and Neutral at all times. To shift into Park when driving below 5 mph (8
km/h), touch the button on the drive mode strip while pressing the brake pedal. In emergency situations when driving above 5
mph (8 km/h), press and hold the Park button to slowly bring the vehicle to a stop.
To shift into Neutral, open Controls to bring up the drive mode strip, then press and hold Neutral until Neutral engages.
The touchscreen is the preferred method to manually shift. However, in the unlikely situation in which the touchscreen is
unavailable and therefore can't be used, the drive mode selector on the center consoleoverhead console automatically
activates and must be used to shift (see Shift Using the Center Console on page 410Shift Using the Overhead Console on
page 408).
If you try to shift when it is prohibited by the current driving speed, the instrument paneltouchscreen displays an alert, a chime
sounds, and the drive mode does not change.
Owner's Manual
405
Owners Manual
Shift Using the Touchscreen
When you press the brake pedal when CybertruckModel SModel XModel 3Model Y is parked, the drive mode strip displays on
the driver's side of the touchscreen. Use the drive mode strip to shift CybertruckModel SModel XModel 3Model Y: Swipe up
for Drive, swipe down for Reverse, or press the drive mode strip for Park.
The touchscreen always shows which gear CybertruckModel SModel XModel 3Model Y is in, but the drive mode strip is
hidden when driving at highway speeds. To show the drive mode strip at any time, swipe right from the left edge of the
touchscreen.
To shift into Park when driving below 5 mph (8 km/h), touch the drive mode strip while pressing the brake pedal. In emergency
situations when driving above 5 mph (8 km/h), press and hold the gear strip to slowly bring the vehicle to a stop.
NOTE: To shift from Drive into Reverse or vice versa, the driving speed must be less than 5 mph (8 km/h).
The touchscreen is the preferred method to manually shift. However, in the unlikely situation in which the touchscreen is
unavailable and therefore can't be used, the drive mode selector on the overhead console automatically activates and must be
used to shift (see Shift Using the Overhead Console on page 407).
If you try to shift when it is prohibited by the current driving speed, the touchscreen displays an alert, a chime sounds, and the
drive mode does not change.
Auto Shift out of Park
Auto Shift out of Park is a BETA feature and is disabled by default. When disabled, use the touchscreen or the overhead
console to manually shift. To enable Auto Shift out of Park, touch Controls > Dynamics > Auto Shift out of Park.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The touchscreen displays the selected drive mode when the driver's door is closed and seat belt is buckled.
406
Owner's Manual
Owners Manual
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, Park; see Shift Using the Touchscreen on page 406).
Confirm the drive mode selection and follow the instructions on the touchscreen before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically select a suitable drive mode without confirming the
selection before you start to drive.
If Auto Shift out of Park is unavailable, the touchscreen displays a message.
CybertruckModel SModel XModel 3Model Y automatically selects a drive mode when:
• Auto Shift out of Park is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park.
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the overhead console is not activated (see Shift Using the Overhead Console on page 407).
• The cameras are free of obstructions (see Cameras on page 1135) and CybertruckModel SModel XModel 3Model Y has
enough input to make a selection.
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically select drive modes in Valet Mode.
Auto Shift out of Park
Auto Shift out of Park is a BETA feature and is disabled by default. When disabled, use the touchscreen or the overhead
console to manually shift. To enable Auto Shift out of Park, touch Controls > Dynamics > Auto Shift out of Park.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The touchscreen displays the selected drive mode when the driver's door is closed and seat belt is buckled.
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, Park; see Shift Using the Touchscreen on page 405).
Confirm the drive mode selection and follow the instructions on the touchscreen before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically select a suitable drive mode without confirming the
selection before you start to drive.
If Auto Shift out of Park is unavailable, the touchscreen displays a message.
CybertruckModel SModel XModel 3Model Y automatically selects a drive mode when:
• Auto Shift out of Park is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park.
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the overhead console is not activated (see Shift Using the Overhead Console on page 408).
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically select drive modes in Valet Mode.
Shift Using the Overhead Console
In addition to manually shifting on the touchscreen, you can shift by pressing P, R, N or D located on the overhead console. In
most situations, these buttons are not available until you press one of the buttons to activate it. When active, the LEDs
associated with each button illuminate and when you select P, R, N or D, the associated LED illuminates.
Owner's Manual
407
Owners Manual
In situations where the touchscreen is unavailable (for example, experiencing a technical issue), or
CybertruckModel SModel XModel 3Model Y is in Valet or Transport Mode, the drive mode selector on the overhead console
illuminates automatically and there is no need to touch it.
NOTE: You can also activate the drive mode selector on the overhead console by simultaneously and briefly pressing both
scroll buttons on the steering wheel. However, if you press and hold both buttons simultaneously, the drive mode selector
activates and the touchscreen restarts (see Restarting the Touchscreen on page 1114).
NOTE: The front trunk must be closed to shift using the overhead console.
1. Park
2. Reverse
3. Neutral
4. Drive
NOTE: When the touchscreen is available for shifting and you have manually activated the drive mode selector on the overhead
console, the overhead console automatically deactivates if you don't shift after a short amount of time.
Shift Using the Overhead Console
In addition to manually shifting on the touchscreen, you can shift by pressing P, R, N or D located on the overhead console. In
most situations, these buttons are not available until you press the brake and touch one of the buttons to activate it. When
active, the LEDs associated with each button illuminate and when you select P, R, N or D, the associated LED illuminates
amber.
In situations where the touchscreen is unavailable (for example, experiencing a technical issue), or
CybertruckModel SModel XModel 3Model Y is in Valet or Transport Mode, the drive mode selector on the overhead console
activates automatically and there is no need to touch it.
NOTE: You can also activate the drive mode selector on the overhead console by simultaneously and briefly pressing both
scroll buttons on the steering wheel. However, if you press and hold both buttons simultaneously, the drive mode selector
activates and the touchscreen restarts (see Restarting the Touchscreen or Instrument Panel on page 34).
NOTE: The front trunk must be closed to shift using the overhead console.
408
Owner's Manual
Owners Manual
1. Park
2. Reverse
3. Neutral
4. Drive
NOTE: When the touchscreen is available for shifting and you have manually activated the drive mode selector on the overhead
console, the overhead console automatically deactivates if you don't shift within 10 seconds.
Auto Shift (Beta)
NOTE: Auto Shift is a Beta feature and is disabled by default.
NOTE: Depending on market region, vehicle configuration, options purchased, and software version, your vehicle may not be
equipped with Auto Shift (Beta) or the features may not operate exactly as described.
Auto Shift an shift between Drive and Reverse, or out of Park, to assist with actions such as turns, parking, or reversing out of a
parking spot. To enable, touch Controls > Pedals & Steering > Auto Shift, where you can select between On or Out of Park.
When On, Auto Shift lets you shift without using the touchscreen based on your surroundings. This assists with multi-point
turns, reversing out of a parking spot, parallel parking, and similar driving maneuvers. When the vehicle assists with shifting, a
readiness indicator appears on the instrument clustertouchscreen .
With Out of Park, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive or Reverse when
shifting out of Park (such as pulling out of a parking spot).
CybertruckModel SModel XModel 3Model Y selects a drive mode when:
• Auto Shift is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park (for Out of Park) or in Drive or Reverse (for On).
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the center console is not activated.
Auto Shift is designed to enhance your driving experience and may only appear in certain circumstances, such as requiring a
vehicle or object in the front and/or rear to begin the maneuver. Confirm the drive mode selection and follow the instructions
on the instrument clustertouchscreen before you press the accelerator.
To override the selection, press the brake pedal and use the drive mode strip on the touchscreen to manually shift into your
desired Drive Mode. Once you override, you’ll need to shift gears again for Auto Shift to reappear. If Auto Shift is unavailable,
the instrument clustertouchscreen displays a message.
Owner's Manual
409
Owners Manual
NOTE: CybertruckModel SModel XModel 3Model Y does not allow Auto Shift in certain modes and driving situations,
including but not limited to: Valet Mode, Track Mode, Creep, Trailer Mode, etc.
WARNING: Never rely on Auto Shift without confirming the selection before proceeding. Always remain attentive,
monitor your surroundings, and maneuver safely.
Auto Shift out of Park
NOTE: Auto Shift out of Park is a BETA feature and is disabled by default.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The instrument panel displays the selected drive mode when the driver's door is closed and seat belt is buckled.
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, or Park).
Confirm the drive mode selection and follow the instructions on the instrument panel before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically select a suitable drive mode without confirming the
selection before you start to drive.
If Auto Shift out of Park is unavailable, the instrument panel displays a message.
CybertruckModel SModel XModel 3Model Y automatically selects a drive mode when:
• Auto Shift out of Park is enabled (touch Controls > Pedals & Steering > Auto Shift out of Park).
• CybertruckModel SModel XModel 3Model Y is in Park.
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the center console is not activated.
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically select drive modes in Valet Mode.
Auto Shift out of Park is disabled by default. When disabled, use the touchscreen or the center console to manually shift. To
enable Auto Shift out of Park, touch Controls > Pedals & Steering > Auto Shift out of Park.
Shift Using the Center Console
In addition to manually shifting on the touchscreen, you can shift by pressing P, R, N or D located on the center console. In
most situations, these buttons are not available until you press one of the buttons to activate it. When active, the LEDs
associated with each button illuminate and when you select P, R, N or D, the associated LED illuminates amber.
In situations where the touchscreen is unavailable (for example, experiencing a technical issue), or
CybertruckModel SModel XModel 3Model Y is in Valet or Transport Mode, the drive mode selector on the center console
activates automatically and there is no need to touch it.
NOTE: You can also activate the drive mode selector on the center console by simultaneously and briefly pressing both scroll
buttons on the steering yoke (or steering wheel). However, if you press and hold both buttons simultaneously, the drive mode
selector activates and the touchscreen restarts (see Restarting the Touchscreen or Instrument Panel on page 34).
NOTE: The front trunk, rear trunk, and doors must be closed to shift using the center console.
410
Owner's Manual
Owners Manual
1. Park
2. Reverse
3. Neutral
4. Drive
NOTE: When the touchscreen is available for shifting and you have manually activated the drive mode selector on the center
console, the center console automatically deactivates if you don't shift within 10 seconds.
Park
To manually shift into Park, press the brake pedal and touch the Park button on the touchscreen's drive mode strip. If the
touchscreen is unavailable, press Park on the drive mode selector located on the center consoleoverhead consoleoverhead
console.
CybertruckModel SModel XModel 3Model Y automatically shifts into Park to prevent roll-away while driving in low speeds.
This happens whenever you connect a charge cable, unbuckle your seat belt, or open the door while in Drive or Neutral.
Ensure the charge cable is removed, buckle your seat belt, and close the door before shifting out of Park.
Attempting to engage the parking brake above 5 mph (8 km/h) will result in emergency braking (see Braking and Stopping on
page 461Braking and Stopping on page 1234).
NOTE: In emergency situations, if the brakes are not functioning properly, you can press and hold the Park button on the
touchscreen's drive mode strip to bring CybertruckModel SModel XModel 3Model Y to a stop. Do not use this method to stop
the vehicle unless absolutely necessary.
NOTE: In emergency situations, if the brakes are not functioning properly, you can press and hold the Park button on the
touchscreen's drive mode strip to apply the brakes and remove drive torque while the button is held. Do not use this method to
stop the vehicle unless absolutely necessary.
NOTE: You must always press the brake pedal to shift out of Park.
CAUTION: CybertruckModel SModel XModel 3Model Y will not shift out of Park if a charge cable is plugged in, or if the
charge port is unable to determine whether a charging cable is plugged in. In situations when
CybertruckModel SModel XModel 3Model Y does not shift out of Park, check the instrument panel or touchscreen for
instructions on how to proceed.
WARNING: It is the driver's responsibility to always ensure the vehicle is in Park before exiting. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically shift into Park for you.
Owner's Manual
411
Owners Manual
Drive
To manually shift into Drive, swipe up on the drive mode strip located on the touchscreen or, if the touchscreen is unavailable,
press D on the drive mode selector located on the center consoleoverhead consoleoverhead console. You can shift into Drive
when CybertruckModel SModel XModel 3Model Y is stopped or moving less than 5 mph (8 km/h) in Reverse.
Reverse
To manually shift into Reverse, swipe down on the drive mode strip located on the touchscreen or, if the touchscreen is
unavailable, press R on the drive mode selector located on the center consoleoverhead consoleoverhead console. You can
shift into Reverse when CybertruckModel SModel XModel 3Model Y is stopped or moving less than 5 mph (8 km/h) in Drive.
You can manually close the park assist view on the touchscreen by touching the X in the upper corner.
Neutral
Neutral allows CybertruckModel SModel XModel 3Model Y to roll freely when you are not pressing the brake pedal. To shift
into Neutral, do any of the following:
• Open Controls, then press and hold the Neutral icon on the drive mode strip until CybertruckModel SModel XModel
3Model Y engages Neutral.
• Open Controls, then press and hold the Neutral icon on the drive mode strip until CybertruckModel SModel XModel
3Model Y engages Neutral.
• Swipe from the edge of the touchscreen towards the passenger to bring up the drive mode strip and press Neutral.
• Choose Neutral from the drive mode selector on the overhead consoleoverhead console.
NOTE: When CybertruckModel SModel XModel 3Model Y is traveling over 5 mph (8 km/h) and you swipe up or down on the
touchscreen's drive mode strip, a Neutral icon displays at the bottom of the drive mode strip from which you can also choose
to engage Neutral.
NOTE: You must press the brake pedal to shift out of Neutral if CybertruckModel SModel XModel 3Model Y is moving slower
than approximately 5 mph (8 km/h).
CybertruckModel SModel XModel 3Model Y automatically shifts into Park when you open the driver's door to exit the vehicle
unless the vehicle is in certain modes such as Transport or Car Wash Mode which allows the vehicle to stay in Neutral even
when you leave.
Keeping Your Vehicle in Neutral (Transport Mode)
To keep CybertruckModel SModel XModel 3Model Y in Neutral when you exit, allowing it to roll freely (for example, pulling
onto a flatbed truck), you must activate Transport mode:
1. Shift into Park.
2. Press the brake pedal.
3. Touch Controls > Service > Towing. The touchscreen displays a message reminding you how to properly transport
CybertruckModel SModel XModel 3Model Y.
4. Press the Transport Mode. It turns blue to show that CybertruckModel SModel XModel 3Model Y is now in Transport
Mode. CybertruckModel SModel XModel 3Model Y is now free-rolling and can slowly be rolled (no faster than walking
speed) for short distances or winched (for example, onto a flatbed truck).
For more information on Transport Mode, see Activate Transport Mode on page 913Activate Transport Mode on page
922Activate Transport Mode on page 1441.
NOTE: In Transport mode, CybertruckModel SModel XModel 3Model Y does not shift into a drive mode. You must first cancel
Transport mode by touching Transport Mode again. Transport mode also cancels if you use the touchscreen or drive mode
selector on the center consoleoverhead consoleoverhead console to shift into Park or if you manually apply the parking brake
by touching Controls > Safety > Parking Brake.
412
Owner's Manual
Owners Manual
Shifting
Shift Using the Touchscreen
When you press the brake pedal when parked, the drive mode strip displays on one side of the touchscreen. Use the drive
mode strip to shift CybertruckModel SModel XModel 3Model Y: swipe up for Drive, swipe down for Reverse or touch the P for
Park or N for Neutral. The drive mode strip is always available on the touchscreen when you touch Controls.Swipe from the
edge of the touchscreen towards the passenger to bring up the drive mode strip.
NOTE: To shift from Drive into Reverse or vice versa, the driving speed must be less than 5 mph (8 km/h).
The touchscreen's drive mode strip displays Park and Neutral at all times. To shift into Park when driving below 5 mph (8
km/h), touch the button on the drive mode strip while pressing the brake pedal. In emergency situations when driving above 5
mph (8 km/h), press and hold the Park button to slowly bring the vehicle to a stop.
To shift into Neutral, open Controls to bring up the drive mode strip, then press and hold Neutral until Neutral engages.
The touchscreen is the preferred method to manually shift. However, in the unlikely situation in which the touchscreen is
unavailable and therefore can't be used, the drive mode selector on the center consoleoverhead console automatically
activates and must be used to shift (see Shift Using the Center Console on page 410Shift Using the Overhead Console on
page 408).
If you try to shift when it is prohibited by the current driving speed, the instrument paneltouchscreen displays an alert, a chime
sounds, and the drive mode does not change.
Owner's Manual
413
Owners Manual
Shift Using the Touchscreen
When you press the brake pedal when CybertruckModel SModel XModel 3Model Y is parked, the drive mode strip displays on
the driver's side of the touchscreen. Use the drive mode strip to shift CybertruckModel SModel XModel 3Model Y: Swipe up
for Drive, swipe down for Reverse, or press the drive mode strip for Park.
The touchscreen always shows which gear CybertruckModel SModel XModel 3Model Y is in, but the drive mode strip is
hidden when driving at highway speeds. To show the drive mode strip at any time, swipe right from the left edge of the
touchscreen.
To shift into Park when driving below 5 mph (8 km/h), touch the drive mode strip while pressing the brake pedal. In emergency
situations when driving above 5 mph (8 km/h), press and hold the gear strip to slowly bring the vehicle to a stop.
NOTE: To shift from Drive into Reverse or vice versa, the driving speed must be less than 5 mph (8 km/h).
The touchscreen is the preferred method to manually shift. However, in the unlikely situation in which the touchscreen is
unavailable and therefore can't be used, the drive mode selector on the overhead console automatically activates and must be
used to shift (see Shift Using the Overhead Console on page 407).
If you try to shift when it is prohibited by the current driving speed, the touchscreen displays an alert, a chime sounds, and the
drive mode does not change.
Auto Shift out of Park
Auto Shift out of Park is a BETA feature and is disabled by default. When disabled, use the touchscreen or the overhead
console to manually shift. To enable Auto Shift out of Park, touch Controls > Dynamics > Auto Shift out of Park.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The touchscreen displays the selected drive mode when the driver's door is closed and seat belt is buckled.
414
Owner's Manual
Owners Manual
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, Park; see Shift Using the Touchscreen on page 406).
Confirm the drive mode selection and follow the instructions on the touchscreen before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically select a suitable drive mode without confirming the
selection before you start to drive.
If Auto Shift out of Park is unavailable, the touchscreen displays a message.
CybertruckModel SModel XModel 3Model Y automatically selects a drive mode when:
• Auto Shift out of Park is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park.
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the overhead console is not activated (see Shift Using the Overhead Console on page 407).
• The cameras are free of obstructions (see Cameras on page 1135) and CybertruckModel SModel XModel 3Model Y has
enough input to make a selection.
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically select drive modes in Valet Mode.
Auto Shift out of Park
Auto Shift out of Park is a BETA feature and is disabled by default. When disabled, use the touchscreen or the overhead
console to manually shift. To enable Auto Shift out of Park, touch Controls > Dynamics > Auto Shift out of Park.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The touchscreen displays the selected drive mode when the driver's door is closed and seat belt is buckled.
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, Park; see Shift Using the Touchscreen on page 405).
Confirm the drive mode selection and follow the instructions on the touchscreen before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
CybertruckModel SModel XModel 3Model Y to automatically select a suitable drive mode without confirming the
selection before you start to drive.
If Auto Shift out of Park is unavailable, the touchscreen displays a message.
CybertruckModel SModel XModel 3Model Y automatically selects a drive mode when:
• Auto Shift out of Park is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park.
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the overhead console is not activated (see Shift Using the Overhead Console on page 408).
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically select drive modes in Valet Mode.
Shift Using the Overhead Console
In addition to manually shifting on the touchscreen, you can shift by pressing P, R, N or D located on the overhead console. In
most situations, these buttons are not available until you press one of the buttons to activate it. When active, the LEDs
associated with each button illuminate and when you select P, R, N or D, the associated LED illuminates.
Owner's Manual
415
Owners Manual
In situations where the touchscreen is unavailable (for example, experiencing a technical issue), or
CybertruckModel SModel XModel 3Model Y is in Valet or Transport Mode, the drive mode selector on the overhead console
illuminates automatically and there is no need to touch it.
NOTE: You can also activate the drive mode selector on the overhead console by simultaneously and briefly pressing both
scroll buttons on the steering wheel. However, if you press and hold both buttons simultaneously, the drive mode selector
activates and the touchscreen restarts (see Restarting the Touchscreen on page 1114).
NOTE: The front trunk must be closed to shift using the overhead console.
1. Park
2. Reverse
3. Neutral
4. Drive
NOTE: When the touchscreen is available for shifting and you have manually activated the drive mode selector on the overhead
console, the overhead console automatically deactivates if you don't shift after a short amount of time.
Shift Using the Overhead Console
In addition to manually shifting on the touchscreen, you can shift by pressing P, R, N or D located on the overhead console. In
most situations, these buttons are not available until you press the brake and touch one of the buttons to activate it. When
active, the LEDs associated with each button illuminate and when you select P, R, N or D, the associated LED illuminates
amber.
In situations where the touchscreen is unavailable (for example, experiencing a technical issue), or
CybertruckModel SModel XModel 3Model Y is in Valet or Transport Mode, the drive mode selector on the overhead console
activates automatically and there is no need to touch it.
NOTE: You can also activate the drive mode selector on the overhead console by simultaneously and briefly pressing both
scroll buttons on the steering wheel. However, if you press and hold both buttons simultaneously, the drive mode selector
activates and the touchscreen restarts (see Restarting the Touchscreen or Instrument Panel on page 34).
NOTE: The front trunk must be closed to shift using the overhead console.
416
Owner's Manual
Owners Manual
1. Park
2. Reverse
3. Neutral
4. Drive
NOTE: When the touchscreen is available for shifting and you have manually activated the drive mode selector on the overhead
console, the overhead console automatically deactivates if you don't shift within 10 seconds.
Auto Shift (Beta)
NOTE: Auto Shift is a Beta feature and is disabled by default.
NOTE: Depending on market region, vehicle configuration, options purchased, and software version, your vehicle may not be
equipped with Auto Shift (Beta) or the features may not operate exactly as described.
Auto Shift an shift between Drive and Reverse, or out of Park, to assist with actions such as turns, parking, or reversing out of a
parking spot. To enable, touch Controls > Pedals & Steering > Auto Shift, where you can select between On or Out of Park.
When On, Auto Shift lets you shift without using the touchscreen based on your surroundings. This assists with multi-point
turns, reversing out of a parking spot, parallel parking, and similar driving maneuvers. When the vehicle assists with shifting, a
readiness indicator appears on the instrument clustertouchscreen .
With Out of Park, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive or Reverse when
shifting out of Park (such as pulling out of a parking spot).
CybertruckModel SModel XModel 3Model Y selects a drive mode when:
• Auto Shift is enabled.
• CybertruckModel SModel XModel 3Model Y is in Park (for Out of Park) or in Drive or Reverse (for On).
• The driver's seat belt is fastened.
• The brake pedal is pressed.
• All doors and trunks are closed.
• The drive mode selector on the center console is not activated.
Auto Shift is designed to enhance your driving experience and may only appear in certain circumstances, such as requiring a
vehicle or object in the front and/or rear to begin the maneuver. Confirm the drive mode selection and follow the instructions
on the instrument clustertouchscreen before you press the accelerator.
To override the selection, press the brake pedal and use the drive mode strip on the touchscreen to manually shift into your
desired Drive Mode. Once you override, you’ll need to shift gears again for Auto Shift to reappear. If Auto Shift is unavailable,
the instrument clustertouchscreen displays a message.
Owner's Manual
417
Owners Manual
NOTE: CybertruckModel SModel XModel 3Model Y does not allow Auto Shift in certain modes and driving situations,
including but not limited to: Valet Mode, Track Mode, Creep, Trailer Mode, etc.
WARNING: Never rely on Auto Shift without confirming the selection before proceeding. Always remain attentive,
monitor your surroundings, and maneuver safely.
Auto Shift out of Park
NOTE: Auto Shift out of Park is a BETA feature and is disabled by default.
When Auto Shift out of Park is enabled, CybertruckModel SModel XModel 3Model Y is designed to automatically select Drive
or Reverse. The instrument panel displays the selected drive mode when the driver's door is closed and seat belt is buckled.
To override the selection, press the brake pedal and use the drive mode strip on touchscreen to shift into your desired drive
mode (Drive, Reverse, or Park).
Confirm the drive mode selection and follow the instructions on the instrument panel before you press the accelerator.
WARNING: As always, be aware of your vehicle and surroundings before driving. Never rely on
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 2024.14_0524.pdf
Replacement Service Bulletin Number:
MFR Communication Date: 2024-04-30
MFR Internal Campaign ID/Software Version: 2024.14
Communication Type: Over The Air
NHTSA Components: UNKNOWN OR OTHER
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.