Radial ply tire

A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90
degrees to the center line of the tread.

Reinforced tire

A tire designed to operate at higher loads and at higher inflation pressures than the
corresponding standard tire.

Section width

The linear distance between the exteriors of the sidewalls of an inflated tire, excluding
elevations due to labeling, decoration, or protective bands.

Sidewall

The portion of a tire between the tread and bead.

Sidewall separation

The parting of the rubber compound from the cord material in the sidewall.

Snow tire

A tire that attains a traction index equal to or greater than 110, compared to the ASTM
E1136-93 (re-approved 2003, incorporated by reference, see §571.5) Standard Reference Test
Tire when using the snow traction test as described in ASTM F1805-00 (incorporated by
reference, see §571.5), and that is marked with an Alpine Symbol specified in S5.5(i) on at
least one sidewall.

Test rim

The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use
with that tire.

Tread

The portion of a tire that comes into contact with the road.

Tread rib

A tread section running around the circumference of a tire.

Tread separation

The pulling away of the tread from the tire carcass.

255

Owner's Manual

Maintenance
Tread wear
indicators (TWI)

The projections within the principal grooves designed to give a visual indication of the
degrees of wear of the tread.

Wheel-holding
fixture

The fixture used to hold the wheel and tire assembly securely during testing.

Owner's Manual

256

Maintenance
Windshield Wiper Blade, Jets and Fluid
Topping Up Windshield Washer Fluid
The only reservoir into which you can add fluid is the windshield washer fluid reservoir, which is located behind the
powered frunk liner. When the level is low, a message displays on the touchscreen.
To top up the washer fluid:
1. Open the powered frunk.
2. Use a microfiber cloth to clean around the filler cap before opening it to prevent dirt from entering the reservoir.
3. Open the filler cap.
4. While avoiding spilling, fill the reservoir until the fluid level is visible just below the filler neck. The reservoir has a
total capacity of 4.2 liters.

5. Wipe up any spills immediately and wash the affected area with water.
6. Close the filler cap.
CAUTION: Some national or local regulations restrict the use of Volatile Organic Compounds (VOCs). VOCs are
commonly used as freeze protection in washer fluid. Use a washer fluid with limited VOC content only if it
provides adequate freeze resistance for all climates in which you drive Cybertruck.
CAUTION: Use only ethanol-based windshield washer fluid meant for automotive vehicles. Using other
substances, such as untreated water, can result in bacterial growth within the climate control system resulting
in odor or potential damage that is not covered by warranty. Untreated pure water expands to ice when
freezing, which may result in damage.
CAUTION: Do not add formulated washer fluids that contain water repellent or bug wash. These fluids can
cause streaking, smearing, and squeaking or other noises.

257

Owner's Manual

Maintenance
WARNING: In temperatures below -32° F (0° C), use a washer fluid with antifreeze. In cold weather, using a
washer fluid without antifreeze can impair visibility through the windshield.
WARNING: Windshield washer fluid can irritate eyes and skin. Read and observe the instructions provided by
the washer fluid manufacturer.

Cleaning the Wiper Blade
Periodically clean the edge of the wiper blade and check the rubber for cracks, splits, and roughness. If damaged,
replace the blade immediately to prevent damage to the glass and improve visibility.
Contaminants on the windshield or wiper blade can reduce the effectiveness of the wiper. Contaminants include ice,
wax spray from car washes, washer fluid with bug and/or water repellent, bird droppings, tree sap, and other organic
substances.
Follow these guidelines for cleaning:
1. Lift the wiper arm a short distance away from the windshield, just far enough to access the wiper blade. Do not
lift the wiper arm beyond its intended position.
2. Place a towel between the wiper arm and windshield to avoid scratching or cracking the windshield.
3. Clean the windshield and wiper blade using washer fluid or non-abrasive glass cleaner approved for use on
automotive glass and rubber.
CAUTION: Inappropriate products can cause damage or smears and create glare on the windshield.
4. Gently place the wiper blade back onto the windshield.
5. Test the wiper blade again. If the wiper remains ineffective after cleaning, replace the wiper blade.

Replacing the Wiper Blade
For optimum performance, replace the wiper blade at least once a year. You can purchase a replacement wiper
blade on the Tesla Shop.
CAUTION: Only install a replacement blade that is identical to the original blade. Using an inappropriate blade
can damage the wiper system and windshield.
To replace the wiper blade:
1. Shift into Park and turn off the wiper. Ensure the wiper setting is Off and not in Auto, because the wiper blade
may still sweep if there is any liquid detected on the windshield.
2. Place a towel between the wiper arm and windshield to avoid scratching or cracking the windshield.
3. Lift the wiper arm a short distance away from the windshield, just far enough to access the wiper blade.
CAUTION: Wiper blade does not lock into a lifted position. Do not lift the wiper arm beyond its intended
position or drop it onto the windshield.
4. While holding the wiper arm, press the locking tab, then slide the blade away from the arm. Set the wiper blade
next to the wiper arm.

Owner's Manual

258

Maintenance

5. Disconnect the washer hose from the wiper blade by pulling the hose from the barb fitting.

6. Connect the new washer hose to the barb fitting on the new wiper blade.

259

Owner's Manual

Maintenance

7. Align the new wiper blade on the wiper arm and slide it toward the base of the wiper arm until it locks into place.
8. Ensure the wiper blade is fully secured by lightly pushing and pulling on the blade. The blade should not jostle or
move around.
9. Remove the towel and gently place the wiper blade against the windshield.

Washer Jets
The windshield washer fluid sprays from nozzles along the length of the wiper blade. You cannot adjust them. If a
windshield washer nozzle becomes blocked, use a thin strand of wire to clear any blockages.
If the blade is not dispensing washer fluid, make sure there is enough wiper fluid in the reservoir and refill if needed.
If this issue still persists, check the hose connection between the arm and blade for any leaks, kinks, or
disconnections.
WARNING: Do not operate the washers while cleaning Cybertruck. Windshield washer fluid can irritate eyes
and skin. Read and observe the washer fluid manufacturer’s instructions for safe handling.

Owner's Manual

260

Maintenance
Jacking and Lifting
WARNING: Ensure the equipment you are using is rated for the weight of Cybertruck, including any cargo,
installed accessories, or upgrades before attempting to lift.
Follow the steps below to lift Cybertruck. Ensure that any non-Tesla repair facility is aware of these instructions,
including lift points and warnings.
Using a Jack and Jack Stand
1. Ensure Cybertruck is located in a flat, stable, and secure area with enough space surrounding the vehicle to jack
it.
2. Ensure the vehicle ride height is set to Medium and enable Jack Mode (Controls > Service > Jack Mode see Jack
Mode on page 263) to disable self-leveling.
WARNING: You MUST enable Jack Mode, otherwise the vehicle may try to self-level while on the jack.
Failing to engage Jack Mode may cause serious injury or death.
3. If available, chock the wheel diagonal to the corner you're working on (for example, if you are replacing the rear
driver's side tire, chock the front passenger's side tire).
4. Remove the wheel cover from the wheel with the flat tire (see Removing and Installing Wheel Covers on page
247).
5. Use the lug nut wrench to break loose the lug nuts on the wheel.
6. Place the jack under the vehicle's lift point (shown in green) corresponding to the location you are working on.
WARNING: DO NOT position the jack under the Battery or side rails (shown in red).
Lift points:

7. Following the jack manufacturer's instructions, begin to lift the vehicle, making sure to constantly monitor the
contact with the lift point.
8. Place the jack stand under the appropriate jack stand location in the image corresponding to the area you're
working on. Ensure the jack stand is appropriately oriented and does not touch any of the red areas in the image.
Adjust to meet the jack's height. The vehicle should be able to be solely propped up with the jack stand.
WARNING: Do not get under the vehicle when it is propped up on the jack or jack stands. Doing so may
cause serious injury or death.
Jack stand points:

261

Owner's Manual

Maintenance

9. Slowly lower the jack following manufacturer instructions, constantly monitoring the contact between the vehicle
and the jack stand. Then release the jack from the vehicle's lift point and check that it is secure.
10. To lower the vehicle off of the jack stand, use the jack to raise the vehicle until the jack stand is no longer
supporting the vehicle, remove the jack stand, and slowly lower the vehicle down.
11. Disengage Jack Mode by touching Controls > Service > Jack Mode.
Using a 2-Post Lift:
1. Ensure the vehicle ride height is set to Medium and enable Jack Mode (Controls > Service > Jack Mode see Jack
Mode on page 263) to disable self-leveling.
WARNING: You MUST enable Jack Mode, otherwise the vehicle may try to self-level while on the jack.
Failing to engage Jack Mode may cause serious injury or death.
2. Position the lift arm pads under the lift points at the locations shown.
WARNING: DO NOT position the lift arm pads under the Battery or side rails.
Lift points:

3. Lift the vehicle to working height.
4. Engage any lift safety locks. Follow the lift manufacturer's instructions for details.
WARNING: Failure to correctly engage the safety locks can result in serious injury or death.
5. When done, lower the vehicle down slowly and safely.
6. Disengage Jack Mode by touching Controls > Service > Jack Mode.
WARNING: Never raise Cybertruck when the charge cable is connected, even if charging is not in progress.
WARNING: Do not work on an incorrectly supported vehicle. Doing so can cause serious damage, bodily injury,
or death.

Owner's Manual

262

Maintenance
CAUTION: It is your responsibility to be observant of the vehicle and it's surroundings. Ensure the area is clear
when lifting and lowering Cybertruck and that the doors, front trunk, and tailgate are closed as necessary to
avoid damage.
CAUTION: DO NOT lift from under the Battery or side rails. Place the lift arm pads under the designated body
lift points only. The locations shown are the only approved lifting points for Cybertruck. Lifting at any other
points can cause damage. Damage caused by incorrectly lifting Cybertruck is not covered by the warranty.

Jack Mode
WARNING: Failure to enable Jack Mode can result in the vehicle self-leveling, resulting in damage, injury, or
death.
Cybertruck automatically self-levels, even when the vehicle is "asleep" and the touchscreen is powered off. Before
enabling Jack Mode:
1. Set the ride height to Medium to allow for enough ground clearance for the jack.
NOTE: Due to the large wheels and height of Cybertruck, setting the ride height to High or Very High may not
provide sufficient clearance for you to safely change the tire.
2. Enable Jack Mode (Controls > Service > Jack Mode).
3. To deactivate Jack Mode, press the brake pedal and touch Controls > Service > Jack Mode again. Jack Mode
automatically cancels when you start to drive.
NOTE: Jack mode may be unexpectedly enabled in situations where an object is supporting the vehicle's weight (for
example the bumper of the vehicle is resting on a curb).

Parts and Accessories
Parts, Accessories, and Modifications
Use only genuine Tesla parts and accessories. Tesla performs rigorous testing on parts to ensure their suitability,
safety, and reliability. Purchase these parts from Tesla, where they can be professionally installed and you can receive
expert advice about modifications to Cybertruck. Accessories are available for purchase online at the Tesla Shop.
Some accessories may not be available in your market region or compatible with your exact vehicle.
Tesla is unable to assess parts manufactured by other distributors and therefore accepts no responsibility if you use
non-Tesla parts on Cybertruck.
WARNING: Installing non-approved parts and accessories, or performing non-approved modifications, can
affect the performance of Cybertruck and the safety of its occupants. Any damage caused by using or
installing non-approved parts, or by performing non-approved modifications, is not covered by the warranty.
WARNING: Tesla does not accept liability for death, personal injury or damage that occurs if you use or install
non-approved accessories or make non-approved modifications.

Body Repairs
If your Cybertruck is in a collision, contact Tesla or a Tesla-approved Body Shop to ensure that it is repaired with
genuine Tesla parts. Tesla has selected and approved body shops that meet strict requirements for training,
equipment, quality, and customer satisfaction.
Some repair shops and insurance companies might suggest using non-original equipment or salvaged parts to save
money. However, these parts may not meet Tesla's high standards for quality, fit, and corrosion resistance. In
addition, non-original equipment and salvaged parts (and any damage or failures they might cause) are not covered
by the warranty.

Connecting Accessories to the 48V Power Feeds
Cybertruck is equipped with two power feeds. The power feeds provide access to the 48V low voltage system,
which can be used to power accessories.

263

Owner's Manual

Maintenance
CAUTION: Do not connect a power source (such as a solar panel or external battery) to a power feed. Doing so
may damage Cybertruck.
WARNING: The two power feeds are the only points at which you can connect accessories directly to the low
voltage system. Do not use any other low voltage wiring in Cybertruck to power accessories. Doing so can lead
to unpredictable or unexpected results (such as a total loss of power steering) and can affect the performance
of Cybertruck and the safety of its occupants. Any damage caused by using or installing non-approved parts,
or by performing non-approved modifications, is not covered by the warranty. Tapping into the power feeds
should only be done by knowledgeable and experienced individuals. Tesla does not accept liability for death,
personal injury or damage that occurs if you install accessories using non-approved methods or circuits.
48V Power Feed Specifications
There are two power feeds:
• One power feed is located on the roof (400W maximum draw).
• One power feed is located in the powered frunk (400W maximum draw).
Each power feed operates in the following range:
• Minimum: 28V
• Nominal: 44–50V
• Maximum: 58V
Each power feed contains three wires:
Wire Color

Function

Red with a blue stripe

Positive (+) terminal: Provides 48V power

Green

Provides access to the Local Interconnect Network (LIN)

Roof power feed: Black with a blue stripe

Negative (-) terminal: Provides a grounding point

Powered frunk power feed: Brown with a blue stripe
NOTE: The power feeds are designed to stop providing power when current that exceeds the listed specifications is
detected. If a power feed unexpectedly stops providing power, reset them by touching Controls > Outlets & Mods >
Reset.
CAUTION: If the wires in the vehicle do not match this information, use the mobile app to schedule a service
appointment.
Accessing the Power Feed on the Roof
1. Ensure that Cybertruck is powered off (see Powering Off on page 97).
WARNING: Failure to ensure the vehicle is powered off can result in serious injury. Tesla recommends
wearing appropriate personal protective equipment to mitigate any potential for injury.
2. Locate the strip of applique on the right side of the roof and use a flat, non-marring tool to gently lift under the
edge and release the five clips that hold it in place. Lift upwards to remove the applique.

Owner's Manual

264

Maintenance

3. Locate the shrink-wrapped loop of wires. This is the power feed.

4. Remove the shrink wrap from the power feed, then splice or solder the accessory's wire harness to it.
WARNING: Use extreme care when accessing the power feed. Assume that the low voltage components of
Cybertruck, including all wires and connectors, are always energized. Because the 48V low voltage system
operates at a higher voltage than a typical low voltage system, there is an increased risk of personal injury,
arcing, or component damage if the low voltage components of Cybertruck are handled improperly.
CAUTION: Carefully check the wiring of the accessory and ensure that you are connecting the positive (+)
wire of the accessory to the positive wire (red with a blue stripe) of the power feed, and the negative (-)
wire of the accessory to ground (black with a blue stripe). See 48V Power Feed Specifications on page 264.
Accessories without proper power and grounding may not function as expected, and may be damaged as a
result.
CAUTION: Ensure that the wires are properly insulated (taped or heatshrinked) after splicing or soldering an
accessory's wiring to the power feed.
5. Ensure your accessory or attachment is properly secured to the vehicle.
6. Replace the roof applique by pressing it into place to ensure that the trim clips are secured.
265

Owner's Manual

Maintenance
7. Power on the vehicle (see Starting and Powering Off on page 96) and enable power to the power feed, if desired
(see Enabling Power to the Power Feeds on page 268).
Accessing the Power Feed in the Powered Frunk
To access the power feed in the powered frunk, you must first remove the frunk lining.
1. Open the powered frunk (see Powered Frunk on page 76).
2. Ensure that Cybertruck is powered off (see Powering Off on page 97).
WARNING: Failure to ensure the vehicle is powered off can result in serious injury. Tesla recommends
wearing appropriate personal protective equipment to mitigate any potential for injury.
3. Remove the frunk maintenance panel by pulling it upwards to release the trim clips that hold it in place.

4. Remove the two bump stops (one on each side above the headlights) by turning them counterclockwise.
5. Remove the windshield washer fluid cap.
6. Using a trim tool or flat, plastic tool, remove the two pieces of trim on the bottom of the frunk lining to expose
the four bolts that hold the lining in place.

7. Using a 10 mm socket, remove the four bolts on the bottom of the frunk and the two bolts beneath the
maintenance panel.
Owner's Manual

266

Maintenance

8. Carefully lift the frunk lining partially upward and unplug the emergency interior release connector. Once the
connector is unplugged, the frunk lining can be removed.

CAUTION: As you remove the frunk lining, be careful not to damage or jostle the connector for the powered
frunk emergency interior release.
9. Locate the shrink-wrapped wires. This is the power feed.

267

Owner's Manual

Maintenance

10. Remove the shrink wrap from the power feed, then splice or solder the accessory's wire harness to it.
WARNING: Use extreme care when accessing the power feed. Assume that the low voltage components of
Cybertruck, including all wires and connectors, are always energized. Because the 48V low voltage system
operates at a higher voltage than a typical low voltage system, there is an increased risk of personal injury,
arcing, or component damage if the low voltage components of Cybertruck are handled improperly.
CAUTION: Carefully check the wiring of the accessory and ensure that you are connecting the positive (+)
wire of the accessory to the positive wire (red with a blue stripe) of the power feed, and the negative (-)
wire of the accessory to ground (brown with a blue stripe). See 48V Power Feed Specifications on page
264. Accessories without proper power and grounding may not function as expected, and may be damaged
as a result.
CAUTION: Ensure that the wires are properly insulated (taped or heatshrinked) after splicing or soldering an
accessory's wiring to the power feed.
11. Ensure your accessory or attachment is secured to the vehicle.
12. Replace the powered frunk lining, connect the emergency interior release connector, and replace all fasteners and
trim. Torque the bolts to 12 Nm (8.87 ft-lb).
13. Power on the vehicle (see Starting and Powering Off on page 96) and enable power to the power feed, if desired
(see Enabling Power to the Power Feeds on page 268).
Enabling Power to the Power Feeds
Once you have connected an accessory to a power feed, enable power from the touchscreen. Touch Controls >
Outlets & Mods and then touch a power feed on the touchscreen to enable it.
CAUTION: Leaving an accessory powered depletes the High Voltage Battery. Power to the power feed shuts
off when the capacity of the High Voltage Battery is very low.
By default, the power feeds stop providing power when you exit Cybertruck and close the doors. To instead keep the
power feeds on when you leave the vehicle, touch Keep On Cabin and Bed Outlets (see Keep On Cabin and Bed
Outlets on page 24).

Using RFID Transponders
When attaching an RFID transponder (used by many automated toll systems) inside Cybertruck, place the
transponder next to the rear view mirror. This ensures best results and minimizes any obstruction to your driving
view. Refer to the RFID manufacturer's instructions for specific placement.
NOTE: You can also attach a weather-proof transponder to the front license plate.

Owner's Manual

268

Maintenance
Do It Yourself Maintenance
Learn how to perform simple Do It Yourself procedures, such as replacing the wiper blade and HEPA filter. Go to
https://www.tesla.com/support/do-it-yourself-guides for instructions, animations, and videos of these procedures.
NOTE: Due to market region or vehicle configuration specifics, some parts and procedures may not be available for
your vehicle. When navigating to https://www.tesla.com/support/do-it-yourself-guides, select your vehicle, region,
and/or language to see an updated list of parts and accessories available for your region.
CAUTION: Perform each procedure in a dry and well-lit area. For your safety, only perform a procedure if you
feel comfortable doing so, and always follow provided instructions.

269

Owner's Manual

Specifications
Identification Labels
Vehicle Identification Number
You can find the VIN at the following locations:
• The Tesla mobile app.
• Touch Controls > Software.
• Stamped onto the driver's side A-pillar. Can be seen by looking through the windshield on the driver's side of the
vehicle.

• Printed on the Vehicle Certification label, located on the door pillar. Can be seen when the driver’s door is open.

Owner's Manual

270

Specifications

Emission Control Label
The emission control label is located on the opening face of the powered frunk.

271

Owner's Manual

Specifications
Vehicle Loading
It is important to understand your vehicle's original tire sizes and pressures, and the GVWR (Gross Vehicle Weight
Rating) and GAWR (Gross Axle Weight Rating). This information can be found on two labels attached to the front
door pillar on the driver's side of the vehicle.

1. Tire and Loading Information Label
2. Vehicle Certification Label
WARNING: Overloading Cybertruck has an adverse effect on braking and handling, which can compromise
your safety or cause damage.
CAUTION: Never store large amounts of liquid in Cybertruck. A significant spill can cause electrical
components to malfunction.

Tire and Loading Information Label
The Tire and Loading Information label provides:
• The maximum number of occupant seating positions.
• The maximum vehicle capacity weight.
• The size of the original tires.
• The cold inflation pressures for the original front and rear tires. These pressures are recommended to optimize
ride and handling characteristics.

Owner's Manual

272

Specifications

Never change this label, even if you use different tires in the future.
NOTE: If Cybertruck is loaded to its full capacity, double check all tires to ensure they are inflated to their
recommended pressure levels (see Maintaining Tire Pressures on page 241).
WARNING: Tire pressures printed on the Tire and Loading Information label DO NOT APPLY to towing. When
towing, tire pressures must be increased. For information about the tire pressures required when towing, refer
to see Towing a Trailer on page 138.

Vehicle Certification Label
WARNING: The Vehicle Certification label specifies the weight ratings for Cybertruck based on the tires that
were installed at time of manufacture and the tire pressures indicated on the Tire and Loading Information
label. However, the weight ratings will change if you change the factory-installed tires or inflate tires to a
pressure that differs from those shown on the Tire and Loading Information label.
The Vehicle Certification label provides:
• GVWR - Gross Vehicle Weight Rating. The maximum allowable total mass of Cybertruck. This is calculated as the
weight of Cybertruck equipped with the heaviest factory selectable options, all passengers, fluids, and cargo.
• GAWR FRT and GAWR RR - Gross Axle Weight Rating for the front and rear axles. The GAWR is the maximum
distributed weight that each axle can support.

CAUTION: To prevent damage, never load Cybertruck so that it is heavier than GVWR or exceeds the individual
GAWR weights.

Roof Racks
Cybertruck supports the use of Tesla-approved roof racks. Roof racks can be installed over the roof, over the bed, or
both. To install roof racks, you must use only roof rack systems that have been approved by Tesla. You can find the
roof rack instructions in the box or on the Tesla Shop.
Maximum Load on Roof Racks: 220 lb (100 kg) per 2-crossbar set. For example, a 2-crossbar set placed on the roof
has a maximum load of 220 lb. An additional 2-crossbar set placed over the cargo bed also has a maximum load of
220 lb (100 kg).

273

Owner's Manual

Specifications

See Carrying Accessories and Crossbars on page 146 for more information.
CAUTION: Failure to use the correct roof racks and follow the instructions can cause significant damage.
WARNING: When loading the roof racks, distribute the load evenly and maintain a low center of gravity.
Loaded vehicles, with higher centers of gravity, may handle differently than unloaded vehicles. Take extra
precautions, such as slower speeds and increased stopping distance, when driving heavily loaded roof racks.

Calculating Load Limits
1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on
the “Tire and Loading Information” label.
2. Determine the combined weight of all occupants that will ride in the vehicle.
3. Subtract the combined weight of the occupants from XXX lbs or XXX kg (see Step 1).
4. The resulting figure equals the available cargo load capacity. For example, if the “XXX” amount equals 1400 lbs
(635 kg) and there will be five 150 lb (68 kg) passengers in the vehicle, the amount of available cargo capacity is
650 lbs (1400 ‑ 750 (5 x 150) = 650 lbs) or 295 kg (635 ‑ 340 (5 x 68) = 295 kg).
5. Determine the combined cargo weight being loaded on the vehicle. That weight must not exceed the available
cargo load capacity calculated in Step 4.
WARNING: The powered frunk and the cargo bed are the preferred places to carry objects. In a collision, or
during hard braking and sharp turns, loose items in the cabin could injure occupants.
Example Load Limit Calculations
How much cargo Cybertruck can carry depends on the number and weight of passengers. The following calculated
load limit examples assume passengers weigh 150 lbs (68 kg). If passengers weigh more or less, available cargo
weight decreases or increases respectively.
Driver and one passenger
Description

Total

Vehicle capacity weight

954 lbs (433 kg)

Subtract occupant weight (2 x 150 lbs/68 kg)

300 lbs (136 kg)

Owner's Manual

274

Specifications
Description

Total

Available cargo weight

654 lbs (297 kg)

Driver and four passengers
Description

Total

Vehicle capacity weight

954 lbs (433 kg)

Subtract occupant weight (5 x 150 lbs/68 kg)

750 lbs (340 kg)

Available cargo weight