the vehicle was last charged.
• View Range Tips to understand impacts on battery consumption and suggestions to maximize range and
efficiency.

Owner's Manual

228

Charging and Energy Consumption
Park: Monitors the amount of energy lost while Cybertruck is parked.
• Choose between Since Last Drive or Since Last Charge.
• View how much idle energy has been consumed while your vehicle is parked and suggestions to decrease energy
loss.

Powershare Home Backup
Prerequisites
Before you can use Powershare Home Backup, make sure that the following requirements are met:
• Cybertruck is running vehicle firmware 2024.14 or later.
• You have the Tesla mobile app version 4.31 or later (see Mobile App on page 86).
• You have the Tesla Universal Wall Connector with Powershare Gateway installed in your home.
For more information about installation and to purchase a Tesla Universal Wall Connector, go to the Tesla shop:
https://shop.tesla.com/.

To Use Powershare Home Backup
Before using Powershare Home Backup, enable it from your vehicle's touchscreen by touching Controls > Charging >
Powershare Home Backup .
Once Powershare Home Backup is enabled, your Cybertruck automatically begins to provide power to your house
when:
• The electric grid stops providing power to your home (there is a power outage).
CAUTION: When the grid first stops providing power to your home, your home may lose power briefly as
Cybertruck prepares to begin Powershare Home Backup.
• The high voltage Battery has more energy remaining than the Powershare discharge limit (see Setting the
Discharge Limit on page 230).
• Cybertruck is connected to the Universal Wall Connector.
When Powershare Home Backup is actively providing power to your home, the touchscreen displays
the Tesla Powershare icon.

The charge port status light is also purple to indicate that Cybertruck is providing power from the high voltage
Battery (see Charge Port Light on page 222). Likewise, the Universal Wall Connector shows a streaming purple light.
You can also see the status of the high voltage Battery on the touchscreen, or in the mobile app.

229

Owner's Manual

Charging and Energy Consumption

1. Energy remaining: The total estimated driving distance or energy percentage (depending on your display setting)
available. The amount of energy available to Powershare Home Backup (the amount remaining above the
Powershare limit) is shown in purple.
2. Powershare rate: The amount of power currently being provided by the high voltage Battery.
3. Powershare discharge limit: The level of energy remaining at which at the high voltage Battery stops providing
power.
Maximum Draw
Cybertruck provides a maximum draw of 11.5 kW.
NOTE: The maximum draw may be limited by the charger installed in your home. Tesla strongly recommends that
the charger (such as a Tesla Wall Connector) that you use for Powershare Home Backup is connected to a 240V
circuit.
Setting the Discharge Limit
You can set the discharge limit from the Tesla mobile app by adjusting the slider.

Owner's Manual

230

Charging and Energy Consumption
When Powershare Home Backup is active, you can see how much energy is remaining in the high voltage Battery
above the discharge limit in the vehicle status area of the touchscreen, or by touching Controls > Charging.

To Stop Powershare Home Backup
To stop Cybertruck from providing power to your home, touch Controls > Charging > Stop Powershare
To restart Powershare, touch Controls > Charging > Start Powershare.
Powershare Home Backup also stops providing power when:
• The high voltage Battery discharges past the Powershare discharge limit.
• The electric grid starts supplying power (the power outage ends).
When the grid is about to start providing power again, you receive a notification from the Tesla mobile app and on
the vehicle touchscreen.
CAUTION: When the grid begins providing power to your home again, your home may lose power for several
seconds as Cybertruck stops providing power.

Limitations
Be aware of the following limitations when using Powershare Home Backup.
• While Cybertruck is actively providing power to your home, the AC outlets in the cabin and in the cargo bed are
disabled (see Interior Electronics on page 19 and Cargo Bed Outlets on page 23).
If Powershare Home Backup stops providing power, you receive a notification on the vehicle touchscreen and
through the Tesla mobile app. This may happen for one of the following reasons.
• Your home is drawing more power than Powershare Home Backup can provide. In this case, reduce the load as
much as possible (for example, by turning off large appliances).
• The high voltage Battery is cold. This is more likely in low ambient temperatures (for example, if Cybertruck is
parked in a cold garage) or if Cybertruck has not been driven recently.
• There is an issue with the Universal Wall Connector, with your vehicle's charge port, or with your vehicle's high
voltage Battery. Check the touchscreen for an alert with more information.

231

Owner's Manual

Maintenance
Software Updates
Loading New Software
Tesla updates your vehicle's software wirelessly, constantly providing new features. Tesla recommends you install
software updates at the earliest opportunity on your vehicle. To ensure the fastest and most reliable delivery of
software updates, leave Wi-Fi turned on and connected whenever possible. In most cases, your vehicle must be
connected to Wi-Fi to download the software update (see Wi-Fi on page 89).

Downloading vs. Installing New Software
There are two steps to receiving a new update: downloading the software (which requires Wi-Fi), and installing it.
For your convenience, you can start downloads and installations using the Tesla mobile app.
Download
When a software update is available for download, the download occurs automatically, showing a green arrow at the
top of the touchscreen. If the vehicle is not connected to Wi-Fi, a yellow download icon appears. Although you can
drive while the software update is being downloaded, doing so can interrupt the download if your vehicle loses the
Wi-Fi connection. When the software update is fully downloaded and ready to install, a clock icon displays at the top
of the touchscreen.
NOTE: To ensure the fastest and most reliable download of software updates, leave the Wi-Fi turned on and
connected whenever possible (see Wi-Fi on page 89).
Install
You CANNOT drive while software is being installed. If plugged in, your vehicle will stop charging until the
installation is complete. To start the installation, touch the yellow clock icon at the top of the touchscreen. Touch
Install Now to begin the installation immediately or touch Set For This Time to choose a different start time. At any
time before the update installs, you can touch this clock icon to reschedule. If you are driving Cybertruck at the
scheduled update time, the update is canceled and must be rescheduled. You can also view, download, and install
software updates by navigating to Controls > Software. If available, connect to Wi-FI to download the update.
Software updates are not performed when the following features are active:
• Keep Climate On, Dog Mode, or Camp Mode
• Sentry Mode
NOTE: Software updates will not install if Keep, Dog, or Camp mode are enabled (see Keep Climate On, Dog, and
Camp on page 195).
NOTE: On an as-needed basis, Tesla also sends software updates using a cellular connection.
NOTE: Some software updates take approximately 30 minutes to complete (some may take longer). Cybertruck
must be in Park while the software is being updated.
WARNING: Do not attempt to use the vehicle while the software is being installed. Vehicle functions, including
some safety systems and opening or closing the doors or windows, may be limited or disabled when
installation is in progress and you could damage the vehicle.

Software Update Preferences
Tesla determines how, when, and where to send updates to vehicles based on various factors unique to each release.
In Controls > Software, you can choose how quickly you want to receive updates that are ready for your vehicle. Be
an early adopter by selecting Advanced (which will have additional releases), or wait until others have installed
(which will result in fewer releases) by selecting Standard. Choosing Advanced does not enroll your vehicle in Tesla's
early access program.
Tesla does not update your software upon request for those wanting to receive the latest features and
improvements. Selecting Advanced and consistently connecting to Wi-Fi (see Wi-Fi on page 89) is the best way to
quickly receive the latest software updates.

Owner's Manual

232

Maintenance
If the touchscreen displays a message indicating that a software update was not successfully completed, wait for the
next software update to deploy to your vehicle.
NOTE: The software update screen persists until you install the update. Install a software update as soon as possible.
Any harm resulting from failure to install a software update is not covered by the vehicle’s warranty. Failure or refusal
to install updates can cause some vehicle features to become inaccessible or digital media devices may become
incompatible.
NOTE: Tesla may update or reinstall your vehicle's software as part of the normal diagnostic, repair, and maintenance
process within Tesla Service.
NOTE: Reverting to a previous software version is not possible.

Charging
If Cybertruck is charging when the software update begins, charging stops. Charging resumes automatically when
the software update is complete.

Viewing Release Notes
When a software update is complete, read the release notes displayed on the touchscreen to learn about changes or
new features. To display release notes about the current version of your vehicle's software at any time, touch
Controls > Software > Release Notes.
Tesla strongly recommends reading all release notes. They may contain important safety information or operating
instructions for your Cybertruck.

Maintenance Service Intervals
Service Intervals
Tesla recommends the following maintenance items and intervals, as applicable to your vehicle, to ensure continued
reliability and efficiency of your Cybertruck.
For additional information on vehicle alerts, see Troubleshooting Alerts on page 296.
• Brake fluid health check every 4 years (replace if necessary)*.
• A/C desiccant bag replacement every 8 years.
• HEPA filter replacement every 2 years, or every year in cases of off-road/dirt road driving.
• Clean and lubricate brake calipers every year or 12,500 miles (20,000 km) if in an area where roads are salted
during winter.
• Rotate tires every 6,250 miles (10,000 km) or if tread depth difference is 2/32 in (1.5 mm) or greater, whichever
comes first.
*Heavy brake usage due to towing, mountain descents, or performance driving -- especially for vehicles in hot and
humid environments -- may necessitate more frequent brake fluid checks and replacements.
NOTE: Any damage caused by opening the Battery coolant reservoir is excluded from the warranty.
NOTE: The above intervals are based on typical driving behaviors and scenarios. Depending on various
circumstances such as driving behavior, usage, environmental conditions, etc., the above maintenance items may
need to be performed more or less frequently than specified. Additionally, the above list should not be considered
comprehensive and does not include consumable parts such as the windshield wiper, brake pads, etc.
NOTE: Damages or failures caused by maintenance or repairs performed by non-Tesla certified technicians are not
covered by the warranty.
For more do-it-yourself maintenance procedures and information, see https://www.tesla.com/support/do-ityourself-guides.

233

Owner's Manual

Maintenance
Schedule Service
Scheduling a service visit through the mobile app is easy. After touching Service, select the type of service needed
and follow the directions in the mobile app. Provide as much detail as possible to better help the Service team
identify the cause of concern, such as:
• Photos, sound recordings, or videos.
• Date(s), time(s), and time zone when the issue occurred.
• Approximate speed the vehicle was traveling (if applicable).
• Environmental conditions (rain, snow, cold, etc.).
• Road name and type of road (if applicable).
• Quality of lane markings (if applicable).
• Applicable vehicle settings.
• Identifiable symptoms.
Visit https://www.tesla.com/support/service-visits for more information on scheduling service.

Daily Checks
• Check the Battery’s charge level, displayed on the touchscreen or mobile app.
• Check the condition and pressure of each tire (see Tire Pressures on page 241).
• Check that all exterior lights, horn, turn signals, and the wiper and washers are working.
• Check for any unexpected indicator lights or vehicle alerts on the touchscreen.
• Check the operation of the brakes, including the parking brake.
NOTE: Because Cybertruck uses regenerative braking (see Regenerative Braking on page 118), the brake pads are
typically used less frequently than those in traditional braking systems. To avoid the accumulation of rust and
corrosion, Tesla recommends frequently pressing the brake pedal to apply the mechanical brakes, which dries the
brake pads and rotors.
• Check the operation of the seat belts (see Seat Belts on page 48).
• Look for abnormal fluid deposits underneath Cybertruck that might indicate a leak. It is normal for a small pool of
water to form (caused by the air conditioning system’s dehumidifying process).
• Look around the exterior of Cybertruck and immediately remove any corrosive substances (such as bird
droppings, tree resin, tar spots, dead insects, industrial fallout, etc.) to prevent damage to the exterior (see
Cleaning on page 236).

Weekly Checks
• During wet weather, clean Autopilot cameras weekly (see Cleaning a Camera on page 31). Otherwise, clean them
monthly during dry weather.

Monthly Checks
• Check windshield washer fluid level and top up if necessary (see Topping Up Windshield Washer Fluid on page
257).
• Check that the air conditioning system is operating correctly (see Operating Climate Controls on page 193).
NOTE: In addition to cooling the interior, the air conditioning compressor also cools the Battery. Therefore, in hot
weather, the air conditioning compressor can turn on even if you turned it off. This is normal because the system’s
priority is to cool the Battery to ensure it stays within an optimum temperature range to support longevity and
optimum performance. Also, even when not in use, you may hear Cybertruck emit a whining noise or the sound of
water circulating. These sounds are normal and occur when the internal cooling systems turn on to support various
vehicle functions, such as maintaining the low voltage battery and balancing the temperature of the high voltage
Battery.

Owner's Manual

234

Maintenance
Fluid Replacement Intervals
Battery coolant and brake fluid levels should only be checked by Tesla or a professional automotive repair shop.
Specific service information is available in the Service Manual.
• Battery coolant: Your Battery coolant does not need to be replaced for the life of your vehicle under most
circumstances.
NOTE: Any damage caused by opening the Battery coolant reservoir is excluded from the warranty.
• Brake fluid: Do not top up your brake fluid.

Software
Updating software is important to ensure proper operation and longevity of your vehicle's components. You must
install a software update at the earliest opportunity. See Software Updates on page 232.
Tesla may update or reinstall your vehicle's software as part of the normal diagnostic, repair, and maintenance
process within Service.

High Voltage Safety
Your Cybertruck has been designed and built with safety as a priority. However, be aware of these precautions to
protect yourself from the risk of injury inherent in all high-voltage systems:
• Read and follow all instructions provided on the labels that are attached to Cybertruck. These labels are there for
your safety.
• The high voltage system has no user-serviceable parts. Do not disassemble, remove or replace high voltage
components, cables or connectors. High voltage cables are colored orange for easy identification.
• If a collision occurs, do not touch any high voltage wiring, connectors, or components connected to the wiring.
• In the unlikely event that a fire occurs, immediately contact your local fire emergency responders.
WARNING: Assume that the low voltage components of Cybertruck, including all cables and connectors, are
always energized. 48V low voltage connectors are colored blue for easy identification, and wires that operate
at 48V are marked with blue tape.
Do not handle low voltage cables or connect/disconnect connectors when the low voltage system is powered.
Because the 48V low voltage system operates at a higher voltage than a typical low voltage system, there is an
increased risk of personal injury, arcing, or component damage if the low voltage components of Cybertruck
are handled improperly.
WARNING: Always disconnect the charge cable before working underneath Cybertruck, even if charging is not
in progress.
WARNING: Keep your hands and clothing away from cooling fans. Some fans operate even when Cybertruck is
powered off.
WARNING: Some fluids (Battery acid, Battery coolant, brake fluid, windshield washer additives, etc.) used in
vehicles are poisonous and should not be inhaled, swallowed, or brought into contact with open wounds. For
your safety, always read and follow instructions printed on fluid containers.

235

Owner's Manual

Maintenance
Cleaning
Cleaning the Exterior
To prevent damage to the exterior, immediately remove corrosive substances (such as grease, oil, bird droppings,
tree resin, dead insects, tar spots, road salt, industrial fallout, etc.). Do not wait until Cybertruck is due for a complete
wash. If necessary, use denatured alcohol to remove tar spots and stubborn grease stains, then immediately wash
the area with water and a mild, non-detergent soap to remove the alcohol.
NOTE: It is normal for the stainless steel exterior to mature over time, resulting in minor changes to the reflective
properties and color of the metal.
Dents and Scratches
The stainless steel exterior of Cybertruck is more resistant to dents and dings than most other vehicles. However,
Cybertruck does not have a clear coat on the surface of the exterior body panels, meaning any scratches that appear
are in the stainless steel panels themselves. Anyone performing scratch repair should refer to the applicable "Exterior
Stainless Steel Panel Refinishing" procedure within the Collision Repair Manual on service.tesla.com. In addition, do
not use, and/or immediately remove, chemical, corrosive, or non-pH neutral substances (including but not limited to:
acidic liquids or materials, grease, oil, tree resin, dead insects, tar spots, road salt, industrial fallout, etc.) as they can
cause corrosion on the vehicle's exterior.
CAUTION: Tesla is not liable for any damage caused by failing to refer to official guidance.
Surface Contamination
Over time, you may notice contamination on the surface of the stainless steel body panels. These spots may appear
as orange or brown rust. However, it is important to note that your Cybertruck is not rusting. Refer to the DIY Guide
for more information.
Keep the exterior cameras free of dirt, condensation, or obstructions. These substances can cause unclear pictures
or Autopilot and safety features to stop working (see Cleaning a Camera on page 31).
Follow these steps when washing the exterior of Cybertruck:
1. Before washing, flush grime and grit from the vehicle using a hose. Flush away accumulations of mud in areas
where debris easily collects (such as wheel wells and panel seams). If salt has been used on the highways (such as
during winter months), thoroughly rinse all traces of road salt from the underside of the vehicle, wheel wells, and
brakes.
2. Mix a mild, pH-neutral soap (such as car shampoo) with water until it gets soapy.
3. Soak a soft cleaning sponge in the soap mixture and hand wash Cybertruck.
CAUTION: Some cleaners and car shampoos contain chemicals that can cause damage or discoloration,
especially for plastic trim pieces, exterior lights, or camera lenses. For example, some car cleaning formulas
contain hydroxide or other highly alkaline or caustic ingredients that can damage exterior components. Do
not use acidic products either. Damage or discoloration resulting from cleaning products is not covered by
the warranty.
4. After washing, rinse with clean water to prevent soap from drying on the surfaces.
5. Dry thoroughly with microfiber cloths (ensure the cloths are clean of sand, dirt, rocks, etc.), one in each hand,
rotating in circular motions until the surface is dry.
For a waterless wash:
1. Hand wash using a non-ionic pH-neutral waterless wash with a high quality microfiber towel.
2. Dry any streaks thoroughly with a chamois.
3. Remove oil and grease with an organic solvent, such as alcohol or ethyl alcohol.
NOTE: Do not use alcohol or ethyl alcohol on the head or tail lights.

Owner's Manual

236

Maintenance
For spot cleaning: Use a glass cleaner and microfiber cloth. Spray glass cleaner and wipe in a zig-zag motion when
cleaning large areas, such as entire panels.
Use isopropyl alcohol wipes (such as those used to clean glasses or screens) to clean away small stains.
NOTE: Tesla does not recommend taking Cybertruck through an automatic car wash.
Cleaning Mud
If your vehicle is covered in mud, such as after off-roading, rinse the entire exterior of the vehicle with water. It is
important to regularly clean the exterior of Cybertruck after off-roading because mud and debris can quickly build
up and limit some vehicle functions.
For certain components, such as the underside, wheel wells, panel seams, and radiator, use a power washer to
remove stuck-on mud or debris. Then follow the rest of the regular cleaning on page 236 steps, as explained above.
Wipe away mud from the headlights, tail lights, and cameras, as it may affect your vehicle’s ability to drive safely.
CAUTION: Damage to the vehicle as a result of debris or mud buildup is not covered by the warranty.
Window Cleaning and Treatments
Clean windows and mirrors using an automotive glass cleaner. Do not scrape or use any abrasive cleaning fluid on
glass or mirrored surfaces. Follow the directions in Cleaning the Exterior on page 236 for best practices in cleaning
the exterior glass.
To add a hydrophobic coating to your vehicle's windows, apply the coating only to the side and rear windows, not
the front windshield—doing so may affect the visibility of the autopilot cameras. Follow the hydrophobic coating
manufacturer’s instructions for application details.
NOTE: Tesla is not responsible for any damage associated with applying window treatments on your vehicle.
Car Wash
If taking Cybertruck to an automatic car wash is necessary, Car Wash Mode closes all windows, locks the charge
port, and disables windshield wipers, Sentry Mode, and walk-away door locking. To enable, touch Controls > Car
Wash. Your vehicle must be stationary and not actively charging.
If using an automatic car wash, Enable Free Roll keeps your vehicle in Neutral and activates free roll for the duration
of the wash, while preventing Cybertruck from applying the Parking brake if you leave the driver's seat. To enable,
press on the brake pedal and touch Enable Free Roll; or shift into Neutral.
Car Wash Mode disables if the vehicle's speed exceeds 9 mph (15 km/h) or by touching Exit on the touchscreen.
CAUTION: Failure to put Cybertruck in Car Wash Mode may result in damage (for example, to the charge port
or windshield wipers). Damage caused by car washes is not covered by the warranty.
Cautions for Exterior Cleaning
CAUTION: Do not wash in direct sunlight.
CAUTION: Do not use windshield treatment fluids. Doing so can interfere with wiper friction and cause a
chattering sound.
CAUTION: Do not use hot water, detergents, highly alkaline or caustic cleaning ingredients or solvents,
specifically those containing hydroxide.
CAUTION: If using a pressure washer, maintain a distance of at least 12" (30 cm) between the nozzle and the
surface of Cybertruck. Keep the nozzle moving and do not concentrate the water jet on any one area.
CAUTION: Do not aim water hoses directly at windows, door, or hood seals or at electronic modules or
exposed cabling.
CAUTION: To avoid corrosive damage that may not be covered by the warranty, rinse away any road salt from
the underside of the vehicle, wheel wells, and brakes. After cleaning the vehicle, dry the brakes by going on a
short drive and applying the brakes multiple times.

237

Owner's Manual

Maintenance
CAUTION: Avoid using tight-napped or rough cloths, such as washing mitts. A high-quality microfiber cleaning
cloth is recommended.
CAUTION: If washing in an automatic car wash, use touchless car washes only. These car washes have no parts
(brushes, etc.) that touch the surfaces of Cybertruck. Some touchless car washes use caustic solutions that,
over time, can cause discoloration of decorative exterior trim. Avoid exposure to soaps and chemicals above
pH 13. If unsure, check the product label or ask the staff at the car wash. Damage caused by improper washing
is not covered by the warranty.
CAUTION: If washing in an automatic car wash, make sure the vehicle is locked. In addition, avoid using
controls on the touchscreen that can result in accidentally opening doors or trunks while the vehicle is being
washed. Any damage caused is not covered by the warranty.
CAUTION: Ensure the wipers are off before washing Cybertruck to avoid the risk of damaging the wipers.
CAUTION: Do not use chemical based wheel cleaners or pre-wash products. These can damage the finish on
the wheels.
WARNING: Never spray liquid at a high velocity (for example, if using a pressure washer) towards the charge
port while Cybertruck is charging. Failure to follow these instructions can result in serious injury or damage to
the vehicle, charging equipment, or property.

Cleaning the Interior
Frequently inspect and clean the interior to maintain its appearance and to prevent premature wear. If possible,
immediately wipe up spills and remove marks. For general cleaning, wipe interior surfaces using a soft cloth (such as
microfiber) dampened with a mixture of warm water and mild non-detergent cleaner (test all cleaners on a
concealed area before use). To avoid streaks, dry immediately with a soft lint-free cloth.
Interior Glass
Do not scrape, or use any abrasive cleaning fluid on glass or mirrored surfaces. This can damage the reflective
surface of the mirror and the heating elements in the rear window.
Airbags
Do not allow any substance to enter an airbag cover. This could affect correct operation.
Dashboard and Plastic Surfaces
Do not polish the upper surfaces of the dashboard. Polished surfaces are reflective and could interfere with your
driving view.
Seats
Wipe spills and chemical residues from interior surfaces as soon as possible using a soft cloth moistened with warm
water and non-detergent soap. Wipe gently in a circular motion. Then wipe dry using a soft, lint-free cloth.
Although seating surfaces are designed to repel stains, Tesla recommends regular cleaning to maintain performance
and an as-new appearance. Promptly treat dye transfer from clothing, such as indigo-dyed denim. Avoid contact
with harsh chemicals, including certain cosmetics. Never use cleaners containing alcohol or bleach. Spot-test
cleaners on an inconspicuous area before applying to visible surfaces.
Vacuum seats as needed to remove any loose dirt.
CAUTION: Aftermarket, non-Tesla seat covers may inhibit the sensitivity of a seat's occupancy sensors and
may cause staining or damage.
Carpets
Avoid over-wetting carpets. For heavily soiled areas, use a diluted upholstery cleaner.
Seat Belts
Extend the belts to wipe. Do not use any type of detergent or chemical cleaning agent. Allow the belts to dry
naturally while extended, preferably away from direct sunlight.

Owner's Manual

238

Maintenance
Door Seals
Wipe door seals with a damp cloth to remove any debris. Excessive debris on the door seals can cause damage
when contacting surrounding surfaces. Avoid using alcohol wipes or any chemical products that can potentially
deteriorate the coating on the door seals.
Front and Rear Touchscreens
Clean the touchscreen(s) using a soft lint-free cloth specifically designed to clean monitors and displays. Do not use
cleaners (such as a glass cleaner) or alcohol-based gel products (such as hand sanitizer) and do not use a wet wipe
or a dry statically-charged cloth (such as a recently washed microfiber). To wipe the front touchscreen without
activating buttons and changing settings, you can enable Screen Clean Mode. Touch Controls > Display > Screen
Clean Mode. The display darkens to make it easy to see dust and smudges. To exit Screen Clean Mode, press and
hold HOLD TO EXIT.
Metal Surfaces
Polish, abrasive cleaners, alcohol-based gel products (such as hand sanitizer), and hard cloths can damage the finish
on metal surfaces.
Cautions for Interior Cleaning
CAUTION: Using solvents (including alcohol), alcohol-based gel products (such as hand sanitizer), bleach,
citrus, naphtha, or silicone-based products or additives on interior components can cause damage.
CAUTION: Statically-charged materials can cause damage to the touchscreen.
WARNING: If you notice any damage on an airbag or seat belt, contact Tesla immediately.
WARNING: Do not allow any water, cleaners, or fabric to enter a seat belt mechanism.
WARNING: Exposure to chemical cleaners can be hazardous and can irritate eyes and skin. Read and observe
the instructions provided by the manufacturer of the chemical cleaner.

Using a Car Cover
To preserve the cosmetic appearance of the body when Cybertruck is not being used, use a genuine Tesla car cover.
Car covers can be purchased online from the Tesla Shop.

CAUTION: Use only a Tesla-approved car cover when Cybertruck is plugged in. Using a non-Tesla car cover can
prevent the Battery from being adequately cooled during charging.

Floor Mats
To extend the life of your carpet and make them easier to clean, use genuine Tesla floor mats available online at
http://www.tesla.com. Maintain floor mats by regularly cleaning them and checking that they are properly attached.
Replace floor mats if they become excessively worn.

239

Owner's Manual

Maintenance
WARNING: To avoid potential interference with a foot pedal, ensure that the driver’s floor mat is securely
fastened, and never place an additional floor mat on top of it. Floor mats should always rest on top of the
vehicle carpeting surface and not on another floor mat or other covering.

Owner's Manual

240

Maintenance
Tire Pressures
Displaying Tire Pressures
Tire pressures display on the touchscreen by touching Controls > Service, or use the mobile app. The pressure of
each tire displays in the visualization of Cybertruck, in addition to the time the tire pressures were last read by the
system.
The touchscreen also displays your vehicle's recommended cold tire pressures so you can easily determine how
much to inflate your tires.
To choose whether to display tire pressures using Bar or PSI, touch Controls > Display > Tire Pressure.
NOTE: You may need to drive briefly before the visualization displays the tire pressure values.

Maintaining Tire Pressures

Keep tires inflated to the recommended pressures, even if it differs from the pressure printed on the tire itself. The
Tire and Loading Information label on the center door pillar is visible when the driver door is open and represents a
nominal driving scenario in which the vehicle is carrying cargo in the front trunk and up to five passengers. When
carrying heavy loads, up to the vehicle's GVWR, in a Cybertruck equipped with All Terrain tires, the tire pressures
should be increased.
Tires (Front and Rear)
20" All Season
20" All Terrain

Normal Load*

GVWR**

50 psi

50 psi

50 psi

65 psi

*Normal Load assumes a fully loaded front trunk and up to five occupants (see Calculating Load Limits on page
274).
**GVWR load capacity not exceeding the vehicle's Gross Vehicle Weight Rating (see Weights - Vehicle on page
278).

241

Owner's Manual

Maintenance
CAUTION: If you are towing a trailer, do not use the tire pressures printed on the Tire and Loading Information
Label. Instead, refer to the tire pressures published (see Tire Pressures when Towing on page 139).
The Low Tire Pressure indicator light on the touchscreen alerts you if a tire is under-inflated. This light
does not immediately turn off when you adjust tire pressure. After inflating the tire to the
recommended pressure, you must drive over 15 mph (25 km/h) for a short amount of time to activate
the Tire Pressure Monitoring System (TPMS), which turns off the Low Tire Pressure indicator light.

If the indicator light flashes for one minute whenever you power on Cybertruck, a fault with the TPMS is detected.
Your vehicle’s tire pressures will drop in cold ambient temperatures. If the TPMS indicator light appears, inflate the
tires before driving. The tires will lose approximately one PSI for every 10° F (6° C) drop in outside temperature.
Proper tire pressures help protect tires from potholes and improve range and tire longevity when properly inflated.
WARNING: The Low Tire Pressure indicator light alerts you only in situations when a tire is below the
recommended threshold (as indicated on the Tire and Loading Information label) under normal driving
conditions. It does not alert you when a tire is under-inflated based on the load you are carrying.
WARNING: Under-inflation is the most common cause of tire failures and can cause a tire to overheat, resulting
in severe tire cracking, tread separation, or blowout. This may lead to unexpected loss of vehicle control and
increased risk of injury. Under-inflation also reduces the vehicle's range and tire tread life.

Checking and Adjusting Tire Pressures
WARNING: Check tire pressures using an accurate pressure gauge when tires are cold. It takes only about one
mile (1.6 km) of driving to warm up the tires sufficiently to affect tire pressures. Parking the vehicle in direct
sunlight or in hot weather can also affect tire pressures. If you must check warm tires, expect increased
pressures. Do not let air out of warm tires in an attempt to match recommended cold tire pressures. A hot tire
at or below the recommended cold tire inflation pressure is dangerously under-inflated.
Follow these steps when tires are cold and Cybertruck has been stationary for over three hours:
1. Refer to the Tire and Loading Information label located on the driver’s center door pillar for the target tire
pressure.
2. Remove the wheel cover (see Removing and Installing Wheel Covers on page 247).
3. Remove the valve cap.
4. Firmly press an accurate tire pressure gauge onto the valve to measure pressure.
NOTE: You can also view tire pressures on the touchscreen.

Owner's Manual

242

Maintenance

5. If required, add or remove air to reach the recommended pressure.
NOTE: You can release air by pressing the metal stem in the center of the valve.
6. Re-check pressure using the accurate tire gauge.
7. Repeat steps 5 and 6 as necessary until the tire pressure is correct.
8. Reinstall the valve cap to prevent dirt from entering. Periodically check the valve for damage and leaks.
9. Reinstall the wheel cover.

Tire Pressure Monitoring
Each tire should be checked monthly when cold and inflated to the recommended pressures (see Maintaining Tire
Pressures on page 241). If your vehicle has tires of a different size than the size indicated on the vehicle placard or
tire inflation pressure label, determine the proper tire inflation pressure for those tires.
When the Tire Pressure indicator light displays on the touchscreen to alert you about tire pressure, stop and check
your tires as soon as possible, and inflate them to the proper pressure (see Maintaining Tire Pressures on page 241).
Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation
also reduces range efficiency and tire tread life, and may affect the vehicle's handling and stopping ability.
If Cybertruck detects a fault with the TPMS, this indicator flashes for one minute whenever you power
on Cybertruck.

NOTE: Installing accessories that are not approved by Tesla can interfere with the TPMS.
WARNING: The TPMS is not a substitute for proper tire maintenance, including manually checking tire
pressures and regularly inspecting the condition of tires. It is the driver's responsibility to maintain correct tire
pressure, even if under-inflation has not reached the level for the TPMS to trigger the Tire Pressure indicator