between
CAUTION: Extensive use of Compressor Overclock can damage or shorten the life of the compressor. Damage
caused by using this feature is not covered by the warranty.
• Save Dashcam for Laps - Enable if you want to save a video and data on a USB flash drive when using the Lap Timer. A USB
flash drive must be set up and inserted as described (see USB Drive Requirements for Recording Videos on page 664). The
USB flash drive must contain a folder named TeslaTrackMode. When enabled, Track Mode stores a video and associated
data for each lap. Track Mode also stores the car status and telemetry data with details about the vehicle's position, speed,
acceleration, use of accelerator, etc. You can then view the video recordings and analyze this data, which is saved as
a .CSV file on the USB flash drive, to determine where time is being lost or gained.
NOTE: For some vehicles manufactured after approximately November 1, 2021, the center console USB ports may only
support charging devices. Use the USB port inside the glove box for all other functions.
Track Mode allows you to save up to 20 settings profiles. To delete a chosen profile, touch Delete at the bottom of the settings
screen.
NOTE: You can not change or delete a pre-defined profile provided by Tesla.
Using the Lap Timer
When you enable Track Mode, the map displays a Lap Timer. Follow the onscreen instructions to place a start/finish pin on the
map. Once the pins are placed, press START to initiate the driving (lapping) session. When you drive
CybertruckModel SModel XModel 3Model Y through the start/finish location, the Lap Timer automatically starts timing the
duration of the lap, resetting the timer whenever you pass the start/finish location, and displaying the real-time delta between
the current lap and the fastest lap so far in the driving session. The map highlights the track in blue.
At the completion of each lap, the Lap Timer displays the duration of the lap. It also displays the times associated with the
previous and best laps in the driving session.
If Save Dashcam for Laps is on (see Customizing Track Mode on page 503), and a properly formatted USB flash drive is
inserted in a front USB port, Track Mode saves a video of the driving session (as recorded by the front cameras), along with
a .CSV file that provides detailed information about the lap.
NOTE: To stop the timer at the end of your driving session, touch STOP on the Lap Timer popup window.
Monitoring Vehicle Health
You can easily monitor the health of CybertruckModel SModel XModel 3Model Y when using Track Mode by glancing at the
car status area of the touchscreen. The colors indicate the status of the various components, allowing you to determine the
current operating state and make decisions accordingly. The components are displayed in green when operating within their
ideal temperature range. Colors change as follows:
• The Battery displays blue when cold and red when hot.
• A brake displays blue when cold and red when hot (an early warning for overheating brakes).
• A motor displays blue when it's cold or red when it's hot.
• Dynamic readings of the tire pressures displays on the touchscreen. A tire displays blue when under-used or red when the
peak grip is exceeded.
NOTE: A component displayed in red may indicate a need to stop driving and allow the component to cool.
CAUTION: Any vehicle damage or injuries caused by using Track Mode is the driver's responsibility. The vehicle warranty
does not cover damage caused by excessive overuse of vehicle components. It also does not cover racing, autocross, or
driving in competition.
G-Meter
In Track Mode, a real-time G-Meter displays on the touchscreen. The G-Meter graphically displays peak lateral, acceleration,
and deceleration values in the form of a circular meter. The history of your drive is represented in the shaded area. The GMeter resets at the start of each driving session.

Owner's Manual

507

Owners Manual
NOTE: You can swipe the G-Meter card to display a different card. However, the G-Meter displays as the default card
whenever you engage Track Mode.

Track Mode
Track Mode, available only on Performance CybertruckModel SModel XModel 3Model Y vehicles, is designed to modify the
stability control, traction control, regenerative braking, and cooling systems to increase performance and handling while
driving on closed circuit courses. Track Mode improves cornering ability by intelligently using the motors, and regenerative
and traditional braking systems. When enabled, the cooling system runs at an increased level before, during, and after
aggressive driving sessions to allow your vehicle’s systems to withstand the surplus heat.
NOTE: Track Mode is designed and calibrated for a Performance CybertruckModel SModel XModel 3Model Y equipped with
performance brakes and tires. Vehicles without performance brakes and tires may experience comparatively lower
performance and endurance.
WARNING: Track Mode is designed for use on closed circuit driving courses only. It is the driver’s responsibility to drive
safely and ensure others are not endangered.
WARNING: Track Mode is designed for use by experienced track drivers familiar with the course. Do not use on public
roads. It is the driver’s responsibility to be in control of the vehicle at all times, including on the track. Because vehicle
behavior (including traction and stability control) differs when using Track Mode, always use caution.
Using Track Mode
Track Mode is always disabled when you start CybertruckModel SModel XModel 3Model Y. To enable Track Mode for your
current drive, shift into Park and follow these steps:
1. Touch Controls > Dynamics > Track Mode.
When enabled, TRACK displays on the touchscreen above the driving speed, and a Track Mode pop up window appears on
the map. The car status area of the touchscreen displays a color-coded image of your CybertruckModel SModel XModel
3Model Y that provides you with important at-a-glance status information about the Battery, the motors, the tires and the
brakes. See Monitoring Vehicle Health on page 504.
2. If desired, customize the Track Mode settings by touching Track Mode Settings on the Track Mode pop up window (see
Customizing Track Mode on page 503). You can also access the Track Mode settings by touching Controls > Dynamics,
then touching Customize next to the Track Mode setting.
NOTE: For optimum performance, wait for the battery and motor temperatures to reduce if highlighted in yellow or red.
3. If you want to use the Lap Timer, follow the onscreen instructions to drop a pin on the map to define the lap's start/finish
location. You will then need to press START on the Lap Timer to begin your driving session. Once started, the Lap Timer
starts counting when you drive CybertruckModel SModel XModel 3Model Y past the lap's start/finish location where you
dropped the pin. See Using the Lap Timer on page 504.
4. Shift and GO!
If you started the Lap Timer, each time you pass the start/finish location, the timer resets for the next lap. See Using the
Lap Timer on page 504.
You can also view a real-time accelerometer (G-meter) by swiping the Cards area of the touchscreen. See G-Meter on
page 505.
When Track Mode is on:
◦ Autopilot features are unavailable.
◦ The Slip Start setting is overridden.
◦ The Regenerative Braking setting is overridden.
◦ Stopping Mode is set to the Roll setting in which CybertruckModel SModel XModel 3Model Y is free-rolling at very low
speeds whenever Drive or Reverse is engaged and both the accelerator and brake pedal are released. For details, see
Stopping Mode on page 466.

508

Owner's Manual

Owners Manual
◦ Stopping Mode is set to the Roll setting in which CybertruckModel SModel XModel 3Model Y is free-rolling at very low
speeds whenever Drive or Reverse is engaged and both the accelerator and brake pedal are released. For details, see
Stopping Mode on page 467.
◦ Energy usage increases.
◦ Entertainment features are unavailable.
Use the touchscreen setting to turn Track Mode off at any time. Powering off CybertruckModel SModel XModel 3Model Y
also turns off Track Mode (although it may still appear on the touchscreen if Post-Drive cooling is in progress). When Track
Mode is off, all settings return to their previous state and all features return to their normal operating state.
CAUTION: Driver assistance features are automatically disabled when Track Mode is On. It is the driver’s
responsibility to drive safely and be in control of the vehicle at all times. Driver assistance features automatically reenable when Track Mode is turned Off.
Customizing Track Mode
To customize Track Mode, touch Track Mode Settings on the Track Mode popup window that appears on the map when you
enable Track Mode. You can also access the Track Mode settings by touching Controls > Dynamics, then touching Customize
next to the Track Mode setting. Choose an existing Track Mode setting from the list of pre-defined profiles provided by Tesla.
Or create a new settings profile by touching Add New Settings, entering a name for the settings profile, then adjusting these
settings to suit your preferences or driving scenario, or customize for a specific track:
• Handling Balance - Drag the slider to customize the balance of CybertruckModel SModel XModel 3Model Y in a turn. If
CybertruckModel SModel XModel 3Model Y is too loose, you can choose a front-biased under-steering setup. Difficult to
get the vehicle through a turn? Try a rear-biased setup to increase rotation. You can select any value, in 5% increments,
between 100/0 (for 100% front biased used for under-steering) and 0/100 (for 100% rear biased used for over-steering).
• Stability Assist - Drag the slider to choose the level at which the stability control systems assist in controlling the vehicle.
You can choose any level from -10 to +10. Choosing +10 engages all stability assist systems for controllable driving in
which stability systems remain engaged, whereas -10 disables all stability systems and the stability of the drive rests solely
on the driver. The default setting of 0 represents a balance which provides some stability being automatically controlled
and leaving some control up to the driver.
• Stability Assist - Drag the slider to choose the level at which the stability control systems assist in controlling the vehicle.
You can choose any level from -10 to +10. Choosing +10 engages all stability assist systems for controllable driving in
which stability systems remain engaged, whereas -10 disables all stability systems and the stability of the drive rests solely
on the driver. The default setting of 0 represents a balance which provides some stability being automatically controlled
and leaving some control up to the driver.
• Stability Assist - Choose the level at which the stability control systems assist in controlling the vehicle. Stability Assist
modifies motor torque and selectively applies the brakes to each wheel to make the vehicle more stable and help the driver
maintain control.
WARNING: Drive with caution when customizing Stability Assist. If you lose control of
CybertruckModel SModel XModel 3Model Y, less stability control intervention will be applied and the vehicle may
not stabilize itself. Use only if you have advance experience driving beyond grip limits.
◦ Reduced: Provides the maximum amount of stability control intervention while in track mode. Stability control is
reduced compared to on-road mode.
◦ Minimal: Provides minimal amount of stability control intervention.
◦ Off: Oversteer support is completely disabled and traction control is limited to allow wheel spin.
• Regenerative Braking - Drag the slider to choose how much regenerative braking is available. You can choose any value, in
5% increments, between 0 and 100%. Tesla recommends the 100% setting to prevent overheating the brakes.
• Post-Drive Cooling - Enable if you want the cooling systems to continue cooling the vehicle's components even after you
leave the vehicle. Cooling stops automatically when the components are sufficiently cool, or when you power
CybertruckModel SModel XModel 3Model Y off and back on again. Post-Drive Cooling is useful if you want to quickly cool
the components between driving sessions. If Post-Drive Cooling is set to OFF, the components eventually cool, but it takes
longer.
• Compressor Overclock - Enable if you want to run the cooling compressor beyond its normal operating rate. Doing so
speeds up the cooling process and is useful when performing multiple aggressive driving sessions with very little time in
between

Owner's Manual

509

Owners Manual
CAUTION: Extensive use of Compressor Overclock can damage or shorten the life of the compressor. Damage
caused by using this feature is not covered by the warranty.
• Save Dashcam for Laps - Enable if you want to save a video and data on a USB flash drive when using the Lap Timer. A USB
flash drive must be set up and inserted as described (see USB Drive Requirements for Recording Videos on page 664). The
USB flash drive must contain a folder named TeslaTrackMode. When enabled, Track Mode stores a video and associated
data for each lap. Track Mode also stores the car status and telemetry data with details about the vehicle's position, speed,
acceleration, use of accelerator, etc. You can then view the video recordings and analyze this data, which is saved as
a .CSV file on the USB flash drive, to determine where time is being lost or gained.
NOTE: For some vehicles manufactured after approximately November 1, 2021, the center console USB ports may only
support charging devices. Use the USB port inside the glove box for all other functions.
Track Mode allows you to save up to 20 settings profiles. To delete a chosen profile, touch Delete at the bottom of the settings
screen.
NOTE: You can not change or delete a pre-defined profile provided by Tesla.
Using the Lap Timer
When you enable Track Mode, the map displays a Lap Timer. Follow the onscreen instructions to place a start/finish pin on the
map. Once the pins are placed, press START to initiate the driving (lapping) session. When you drive
CybertruckModel SModel XModel 3Model Y through the start/finish location, the Lap Timer automatically starts timing the
duration of the lap, resetting the timer whenever you pass the start/finish location, and displaying the real-time delta between
the current lap and the fastest lap so far in the driving session. The map highlights the track in blue.
At the completion of each lap, the Lap Timer displays the duration of the lap. It also displays the times associated with the
previous and best laps in the driving session.
If Save Dashcam for Laps is on (see Customizing Track Mode on page 503), and a properly formatted USB flash drive is
inserted in a front USB port, Track Mode saves a video of the driving session (as recorded by the front cameras), along with
a .CSV file that provides detailed information about the lap.
NOTE: To stop the timer at the end of your driving session, touch STOP on the Lap Timer popup window.
Monitoring Vehicle Health
You can easily monitor the health of CybertruckModel SModel XModel 3Model Y when using Track Mode by glancing at the
car status area of the touchscreen. The colors indicate the status of the various components, allowing you to determine the
current operating state and make decisions accordingly. The components are displayed in green when operating within their
ideal temperature range. Colors change as follows:
• The Battery displays blue when cold and red when hot.
• A brake displays blue when cold and red when hot (an early warning for overheating brakes).
• A motor displays blue when it's cold or red when it's hot.
• Dynamic readings of the tire pressures displays on the touchscreen. A tire displays blue when under-used or red when the
peak grip is exceeded.
NOTE: A component displayed in red may indicate a need to stop driving and allow the component to cool.
CAUTION: Any vehicle damage or injuries caused by using Track Mode is the driver's responsibility. The vehicle warranty
does not cover damage caused by excessive overuse of vehicle components. It also does not cover racing, autocross, or
driving in competition.
G-Meter
In Track Mode, a real-time G-Meter displays on the touchscreen. The G-Meter graphically displays peak lateral, acceleration,
and deceleration values in the form of a circular meter. The history of your drive is represented in the shaded area. The GMeter resets at the start of each driving session.
NOTE: You can swipe the G-Meter card to display a different card. However, the G-Meter displays as the default card
whenever you engage Track Mode.

510

Owner's Manual

Owners Manual
Track Mode
Track Mode, available only on Plaid CybertruckModel SModel XModel 3Model Y vehicles, is designed to modify the stability
control, traction control, regenerative braking, and cooling systems to increase performance and handling while driving on
closed circuit courses. Track Mode improves cornering ability by intelligently using the motors, and regenerative and
traditional braking systems. When enabled, the cooling system runs at an increased level before, during, and after aggressive
driving sessions to allow your vehicle’s systems to withstand the surplus heat.
In Track Mode, adaptive suspension damping is optimized for handling and vehicle body control to promote driver confidence
in dynamic maneuvers. Ride height is automatically set to Low and the suspension no longer automatically raises for comfort
over rough surfaces.
WARNING: Track Mode is designed for use only by experienced drivers familiar with closed circuit driving courses. Do
not use on public roads. It is the driver’s responsibility to drive safely and be in control of the vehicle and all times to
ensure safety to self and others. Vehicle behavior (including traction and stability control) differs when using Track
Mode and driver must exercise caution at all times.
WARNING: For speeds above 158 mph (255 km/h), GVWR (Gross Vehicle Weight Rating) and GAWR (Gross Axle Weight
Ratings) must not exceed the maximums stated on the Vehicle Certification label (see Vehicle Loading on page 844).
Using Track Mode
Track Mode is always disabled when you start CybertruckModel SModel XModel 3Model Y. To enable Track Mode for your
current drive, shift into Park and follow these steps:
1. Touch Controls > Pedals & Steering > Track Mode.
When enabled, TRACK displays on the instrument panel above the driving speed, and a Track Mode pane appears on the
map. The Track Mode pane displays important at-a-glance status information about the Battery and the motors (see
Monitoring Vehicle Health on page 513) and a real-time accelerometer (see G-Meter on page 513).
2. If desired, customize the Track Mode settings by touching Customize on the Track Mode pane of the touchscreen (see
Customizing Track Mode on page 512). You can also customize the Track Mode settings by touching Pedals & Steering >
Driving, then touching Customize next to the Track Mode setting.
NOTE: For optimum performance, wait for the battery and motor temperatures to reduce if highlighted in yellow or red.
3. If desired, start the Lap Timer (see Using the Lap Timer on page 513).
4. Shift into gear and GO!
If you started the Lap Timer, each time you pass the start/finish location, the timer resets for the next lap. See Using the
Lap Timer on page 513.
When Track Mode is on:
◦ Autopilot features are unavailable.
◦ The Slip Start setting is overridden.
◦ Energy usage increases.
◦ Entertainment features are unavailable.
◦ Auto Shift (Beta) is disabled (see Auto Shift (Beta) on page 409 for more information).
◦ Settings for Adaptive Suspension Damping are disabled (Track Mode automatically optimizes adaptive damping to
support aggressive driving).
Use the touchscreen setting to turn Track Mode off at any time. Powering off CybertruckModel SModel XModel 3Model Y
also turns off Track Mode (although it may still appear on the touchscreen if Post-Drive cooling is in progress). When Track
Mode is off, all settings return to their previous state and all features return to their normal operating state.
NOTE: If CybertruckModel SModel XModel 3Model Y powers off while Track Mode is still enabled for Post-Drive cooling,
the touchscreen displays a popup that provides quick access to re-enabling it when you power
CybertruckModel SModel XModel 3Model Y back on.

Owner's Manual

511

Owners Manual
CAUTION: Driver assistance features are automatically disabled when Track Mode is On. It is the driver’s responsibility
to drive safely and be in control of the vehicle at all times. Driver Assistance features automatically re-enable when
Track Mode is turned Off.
Top Speed, Tires, and Tire Pressures
A CybertruckModel SModel XModel 3Model Y equipped with Tesla Carbon Ceramic brakes is capable of achieving a top
speed of 200 mph (322 km/h).
To support this top speed, Model S must be equipped with the following tires at the recommended pressures:

Goodyear Supercar 3R

Cold - 32 psi*
Hot - 36 psi*
Hot on high load/banked tracks - 40 psi*

Michelin PS4S

Cold - 32 psi*
Hot - 40 psi*

* For both axles at curb loading conditions.
WARNING: Never attempt to drive at 200 mph (322 km/h) unless CybertruckModel SModel XModel 3Model Y is
equipped with the Tesla Carbon Ceramic brake kit and the appropriate tires described above.
Customizing Track Mode
To customize Track Mode, touch Customize on the Track Mode pane that appears on the map when you enable Track Mode.
You can also access the Track Mode settings by touching Controls > Pedals & Steering, then touching Customize next to the
Track Mode setting. Choose an existing Track Mode setting from the list of pre-defined profiles provided by Tesla. Or create a
new settings profile by touching Add New Settings, entering a name for the settings profile, then adjusting these settings to
suit your preferences or driving scenario, or customize for a specific track:
• Handling Balance - Drag the slider to customize the balance of CybertruckModel SModel XModel 3Model Y in a turn. If
CybertruckModel SModel XModel 3Model Y is too loose, you can choose a front-biased under-steering setup. Difficult to
get the vehicle through a turn? Try a rear-biased setup to increase rotation. You can select any value, in 5% increments,
between 100/0 (for 100% front biased used for under-steering) and 0/100 (for 100% rear biased used for over-steering).
• Stability Assist - Drag the slider to choose the level at which the stability control systems assist in controlling the vehicle.
You can choose any level from -10 to +10. Choosing +10 engages all stability assist systems and is similar to driving without
track mode engaged. Choosing -10 disables all stability systems and the stability of the drive rests solely on the driver. The
default setting of 0 represents a balance which provides some stability being automatically controlled and leaving some
control up to the driver.
• Regenerative Braking - Drag the slider to choose how much regenerative braking is available. You can choose any value, in
5% increments, between 0 and 100%. When using base brakes, Tesla recommends the 100% setting to prevent
overheating. Overheating is not a concern on a CybertruckModel SModel XModel 3Model Y equipped with Carbon
Ceramic brakes.
• Post-Drive Cooling - Enable if you want the cooling systems to continue cooling the vehicle's components even after you
leave the vehicle. Cooling stops automatically when the components are sufficiently cool, or when you power
CybertruckModel SModel XModel 3Model Y off and back on again. Post-Drive Cooling is useful if you want to quickly cool
the components between driving sessions. If Post-Drive Cooling is set to OFF, the components eventually cool, but it takes
longer.
• Brake Temperatures (displays only if CybertruckModel SModel XModel 3Model Y is not equipped with Tesla's Carbon
Ceramic brake kit) - Enable to display brake temperatures as well as warnings associated with the braking system. You may
want to disable in situations in which you have installed an aftermarket high performance braking system.
NOTE: Warnings are automatically disabled on a CybertruckModel SModel XModel 3Model Y equipped with the optional
Tesla Carbon Ceramic brake kit.

512

Owner's Manual

Owners Manual
• Save Dashcam for Laps - Enable if you want to save a video and data on a USB flash drive when using the Lap Timer. A USB
flash drive must be set up and inserted as described (see USB Drive Requirements for Recording Videos on page 664). The
USB flash drive must contain a folder named TeslaTrackMode. When enabled, Track Mode stores a video and associated
data for each lap. Track Mode also stores the car status and telemetry data with details about the vehicle's position, speed,
acceleration, use of accelerator, etc. You can then view the video recordings and analyze this data, which is saved as
a .CSV file on the USB flash drive, to determine where time is being lost or gained.
The currently chosen setting displays on the touchscreen in the top left corner of the Track Mode pane.
Track Mode allows you to save up to 20 settings profiles. To delete a chosen profile, touch Delete at the bottom of the settings
screen.
NOTE: You can not change or delete a pre-defined profile provided by Tesla.
Using the Lap Timer
When you enable Track Mode, the map displays a Lap Timer. Drop a pin on the map to define the lap's start/finish location.
Then press START to begin the driving (lapping) session. Once started, the Lap Timer starts counting when you drive
CybertruckModel SModel XModel 3Model Y past the lap's start/finish location where you dropped the pin. The Lap Timer
automatically starts timing the duration of the lap, resetting the timer whenever you pass the start/finish location, and
displaying the real-time delta between the current lap and the fastest lap so far in the driving session. The map highlights the
track in blue.
At the completion of each lap, the Lap Timer displays the duration of the lap. It also displays the times associated with the
previous and best laps in the driving session.
If Save Dashcam for Laps is enabled (see Customizing Track Mode on page 512), and a properly formatted USB flash drive is
inserted, Track Mode saves a video of the driving session (as recorded by the front cameras), along with a .CSV file that
provides detailed information about the lap.
NOTE: To stop the timer at the end of your driving session, touch STOP on the Lap Timer.
Monitoring Vehicle Health
You can easily monitor the health of CybertruckModel SModel XModel 3Model Y when using Track Mode by glancing at the
touchscreen and the instrument panel.
The touchscreen displays bars that graphically represent the temperatures of the Battery and motors. These bars display with
no color when operating within their ideal temperature range. However, as the Battery or a motor begins to suffer from
reduced performance due to temperature, the associated bar is highlighted in yellow. Then, as the performance becomes more
limited, the color of the bar progresses toward red.
The instrument panel displays dynamic readings of tire pressures and colors a tire's pressure reading red if the tire pressure
becomes low.
If CybertruckModel SModel XModel 3Model Y is not equipped with Tesla's Carbon Ceramic brake kit, the instrument panel
also displays temperature warnings from the front and rear brakes, using yellow as the brakes reach thermal limits and red
when thermal limits are further exceeded.
NOTE: A component displayed in red may indicate the need for the component to cool significantly before it can perform
adequately.
CAUTION: Any vehicle damage or injuries caused by using Track Mode is the driver's responsibility. The vehicle warranty
does not cover damage caused by excessive overuse of vehicle components. It also does not cover racing, autocross, or
driving in competition.
G-Meter
In Track Mode, a real-time G-Meter displays on the Track Mode pane on the touchscreen. The G-Meter graphically displays
peak lateral and longitudinal acceleration values in the form of a circular meter. The history of your drive is represented in the
shaded area. The G-Meter resets at the start of each driving session.

Owner's Manual

513

Owners Manual
Driver Profiles
When you first adjust the driver’s seat, steering wheelsteering yoke (or steering wheel) position, or exterior side mirrors, the
touchscreen prompts you to create a driver profile to save these adjustments. Your profile also saves various preferences you
make while customizing CybertruckModel SModel XModel 3Model Y.
To save your profile settings to the cloud and access them across multiple Tesla vehicles, set up a Tesla Profile (see Using
Tesla Profiles on page 514).
To save your profile settings to the cloud and access them across multiple Tesla vehicles, set up a Tesla Profile (see Using
Tesla Profiles on page 515).
To add a new driver profile, touch the driver profile icon at the top of the touchscreenin Controls. Then touch
Driver Profile Settings > Add New Driver, type the driver's name and touch Create Profile. Follow the onscreen
instructions to save mirror and steering wheel position to the driver profile to save mirror and steering wheel
position to the driver profile.

Check the Use Easy Entry checkbox if you want to save (or use existing) Easy Entry settings in which the driver's seat and the
steering wheelsteering yoke (or steering wheel) are automatically adjusted to make it easy to enter and exit
CybertruckModel SModel XModel 3Model Y.
If you change the position of the driver’s seat, steering wheelsteering yoke (or steering wheel), or exterior side mirrors after
you have saved or chosen a driver profile, the touchscreen prompts you to Save the new position or Restore the previously
saved position (other settings are automatically saved). To change a setting without saving or restoring, just ignore the
prompt.
To delete a driver profile, touch the driver profile icon at the top of the touchscreenin Controls, touch Driver Profile Settings
and select the driver profile you want to remove. Once selected, Delete the driver profile.
NOTE: Valet mode is a built-in driver profile that limits speed and restricts access to some CybertruckModel SModel XModel
3Model Y features (see Valet Mode on page 516).
NOTE: Depending on date of manufacture and options selected at time of purchase, some Model S vehicles are not equipped
with the driver profile feature. Also, in cases where the vehicle is equipped with driver profiles, some features may not be
automatically saved and adjusted based on the driver profile (for example, mirror position).
NOTE: To stop automatic adjustments that are in process based on a driver's profile, touch Stop on the Driver Profile
dropdown menu. Automatic adjustments also stop if you manually adjust a seat, mirror, or the steering wheelsteering yoke (or
steering wheel).
Selecting Between Driver Profiles
To adjust CybertruckModel SModel XModel 3Model Y based on a driver’s profile, touch the driver profile icon
at the top of the touchscreenControls screenControls screen. Then choose the driver, and
CybertruckModel SModel XModel 3Model Y is adjusted based on the settings that have been saved to the
chosen driver profile. See Using Tesla Profiles on page 514 to learn more about saving profile settings to the
cloud for easy access across multiple Tesla vehicles.See Using Tesla Profiles on page 515 to learn more about
saving profile settings to the cloud for easy access across multiple Tesla vehicles.
NOTE: Your preferred Stopping Mode setting does not sync to your driver profile. For more information, see Braking and
Stopping on page 461.
Using Tesla Profiles
(If equipped) Driver profile settings, such as seat adjustments, temperature preferences, navigation Recents and Favorites,
media settings, and data sharing preferences can be saved into a Tesla Profile that is synced to every supported vehicle under
your Tesla Account. This provides convenient access to your profile settings and preferences across all your Tesla supported
vehicles.
To set up your Tesla Profile, navigate to Driver Profile Settings and select your Tesla Account name. You can choose to set it up
as a New Profile or copy the settings from an existing driver profile that you were previously using.

514

Owner's Manual

Owners Manual
To set up a Tesla Profile for additional drivers, share your vehicle with them from the mobile app and navigate to Security &
Drivers > Manage Drivers > Add Driver. Their Tesla Profile will appear in the Driver Profile settings after accepting the invitation
from their Tesla Account. If you remove their access to the vehicle, it also removes their Tesla Profile. For more information on
granting mobile app access, see Granting Access to a Second Driver on page 358. In addition, you can change your profile
picture from your Tesla Mobile App.
NOTE: Some vehicle settings are synced only between similar vehicle models. If the seat, steering, and mirror positions do not
restore as expected, touch Controls > Service > Driver Seat, Steering, & Mirrors Calibration on the affected vehicles. If the
setting for Autopilot Activation does not restore as expected, touch Controls > Autopilot > Autopilot Activation (see Autopilot
Settings on page 553). If the setting for Autopilot Activation does not restore as expected, touch Controls > Autopilot >
Autopilot Activation (see Autopilot Settings on page 553). If the setting for Autopilot Activation does not restore as expected,
touch Controls > Autopilot > Autopilot Activation (see Autopilot Settings on page 553). If the setting for Autopilot Activation
does not restore as expected, touch Controls > Autopilot > Autopilot Activation (see Autopilot Settings on page 553).
NOTE: Tesla Profiles are supported on vehicles with software versions 2022.24 or higher.
To remove your Tesla Profile from a vehicle, remove that vehicle from your Tesla account:
1. In the Tesla mobile app, touch the profile icon in the top-right corner.
2. Touch Add/Remove Products.
3. Touch Remove.
4. Select the vehicle you'd like to remove.
Using Tesla Profiles
Driver profile settings, such as seat adjustments, temperature preferences, navigation Recents and Favorites, media settings,
and data sharing preferences can be saved into a Tesla Profile that is synced to every supported vehicle under your Tesla
Account. This provides convenient access to your profile settings and preferences across all your Tesla supported vehicles.
To set up your Tesla Profile, navigate to Driver Profile Settings and select your Tesla Account name. You can choose to set it up
as a New Profile or copy the settings from an existing driver profile that you were previously using.
To set up a Tesla Profile for additional drivers, share your vehicle with them from the mobile app and navigate to Security &
Drivers > Manage Drivers > Add Driver. Their Tesla Profile will appear in the Driver Profile settings after accepting the invitation
from their Tesla Account. If you remove their access to the vehicle, it also removes their Tesla Profile. For more information on
granting mobile app access, see Granting Access to a Second Driver on page 358. In addition, you can change your profile
picture from your Tesla Mobile App.
NOTE: Some vehicle settings, such as seat, mirror, steering wheel, and air vent positions are only synced between the same
vehicle models. If the seat or steering positions do not restore as expected, touch Controls > Service > Seat & Steering
Calibration on the affected vehicles.
To remove your Tesla Profile from a vehicle, remove that vehicle from your Tesla account:
1. In the Tesla mobile app, touch the profile icon in the top-right corner.
2. Touch Add/Remove Products.
3. Touch Remove.
4. Select the vehicle you'd like to remove.
Saved Settings
A subset of the settings that you choose to customize your CybertruckModel SModel XModel 3Model Y are automatically
saved to your driver's profile. Once saved, a green check mark appears next to the driver profile icon on the touchscreen.
Examples of automatically saved driver profile settings are:
• Navigation, temperature, lights and display settings.
• Autopilot and driving preferences.
NOTE: The settings that are associated with driver profiles vary depending on the vehicle's date of manufacture and version of
software installed.

Owner's Manual

515

Owners Manual
Linking a Driver Profile to a Key Fob
You can link a driver profile to a specific key fob to allow CybertruckModel SModel XModel 3Model Y to automatically select
the correct driver profile when the linked key fob is detected as you approach the vehicle and open the driver's door. To link a
driver profile to a key fob, enter CybertruckModel SModel XModel 3Model Y with the key fob and touch the driver profile icon
at the top of the touchscreen. Select the driver profile you would like to link to the key fob, then touch Link to Key Fob.
NOTE: CybertruckModel SModel XModel 3Model Y detects only one key fob at a time. The driver profile is linked to the key
fob that is detected by the vehicle at that time. Therefore, if you want to link driver profiles to multiple key fobs, ensure that
only the key fob that you would like to link the driver profile to is within detection range while performing the linking
procedure. Move all other key fobs outside of the detection range (at least three feet (one meter) away from
CybertruckModel SModel XModel 3Model Y).
NOTE: CybertruckModel SModel XModel 3Model Y can support up to threeeight linked key fobs. However, a driver profile can
only be linked to one key fob.
To remove the link between a driver profile and key fob, touch the driver profile icon at the top of the touchscreen. Select the
driver profile, then touch the X next to Linked to Key Fob.
Linking a Driver Profile to a Key
You can link a driver profile to a key (or keys) to allow CybertruckModel SModel XModel 3Model Y to automatically select the
correct driver profile when the linked key is detected as you approach the vehicle and open the driver's door. To link a driver
profile to a key, first ensure you are using your desired driver profile, then touch Controls > Locks > Keys. You can toggle the
driver icon to link or delete a key to the desired driver profile. The name of the driver profile appears under the key to show
that it is linked.
NOTE: CybertruckModel SModel XModel 3Model Y supports up to 10 driver profiles. You can link multiple keys to a driver
profile, but you cannot link multiple driver profiles to a single key.
Linking a Driver Profile to a Key
You can link a driver profile to a key (or keys) to allow CybertruckModel SModel XModel 3Model Y to automatically select the
correct driver profile when the linked key is detected as you approach the vehicle and open the driver's door. To link a driver
profile to a key, first ensure you are using your desired driver profile, then touch Controls > Locks > Keys. You can toggle the
driver icon to link or delete a key to the desired driver profile. The name of the driver profile appears under the key to show
that it is linked.
NOTE: CybertruckModel SModel XModel 3Model Y supports up to 10 driver profiles. You can link multiple keys to a driver
profile, but you cannot link multiple driver profiles to a single key.
Easy Entry
You can define an Easy Entry setting that moves the steering wheelsteering yoke (or steering wheel) and driver's seat to make
it easy to enter and exit CybertruckModel SModel XModel 3Model Y. Any driver can use the Easy Entry setting by associating
it with their driver profile. When the Easy Entry setting is associated with a driver profile, the steering wheelsteering yoke (or
steering wheel) and driver's seat automatically adjust when in Park and the driver's seat belt is unbuckled, allowing an easy
exit from (and next entrance into) CybertruckModel SModel XModel 3Model Y. When returning to the vehicle and stepping on
the brake pedal, settings automatically adjust back to the settings used by the most recent driver profile (or based on the key
if it's linked to a driver profile).
To use Easy Entry with a driver profile, ensure the Use Easy Entry box is checked.
WARNING: Never use Easy Entry to move the driver's seat to the full rearward position when a child safety seat is
installed on a rear seat located behind the driver's seat. With reduced clearance, the movement of the seat may impact a
child's legs, cause injury, or dislodge the seat.
NOTE: You can also make it easier to enter or exit CybertruckModel SModel XModel 3Model Y by enabling Auto Lower. For
more information, see Auto Lower on page 1239.
Valet Mode
When CybertruckModel SModel XModel 3Model Y is in Valet mode, the following restrictions apply:
• Key card must be used to access and drive CybertruckModel SModel XModel 3Model Y.

516

Owner's Manual

Owners Manual
• Key card must be used to access and drive CybertruckModel SModel XModel 3Model Y.
• Speed is limited to 70 mph (113 km/h).
• Maximum acceleration and power are limited.
• Front trunk and glovebox are locked.
• Home and Work locations are not available in the navigation system.
• Voice commands are disabled.
• Cruise control is disabled.
• Autopilot convenience features are disabled.
• The Allow Mobile Access setting cannot be changed.
• HomeLink (if available in your market region) is not accessible.
• Driver Profiles are not accessible.
• Some apps, such as Toybox and Theater, are not accessible.
• The touchscreen does not display the list of keys that can access CybertruckModel SModel XModel 3Model Y (see
Managing Keys on page 126).
• The touchscreen does not display the list of keys that can access CybertruckModel SModel XModel 3Model Y (see
Managing Keys on page 1142).
• Wi-Fi and Bluetooth are disabled. When CybertruckModel SModel XModel 3Model Y is in Valet mode, you cannot pair new
Bluetooth devices or view or delete existing paired devices. However, if a Bluetooth-paired device or a known Wi-Fi
network is within range, CybertruckModel SModel XModel 3Model Y connects to it.
NOTE: CybertruckModel SModel XModel 3Model Y does not automatically shift when in Valet Mode.
Starting Valet Mode

With CybertruckModel SModel XModel 3Model Y in Park, touch the driver profile icon at the top of the touchscreenControls
screenControls screen, then touch Valet Mode.
The first time you enter Valet mode, the touchscreen prompts you to create a 4-digit PIN you will use to cancel Valet mode.
When Valet mode is active, the instrument paneltouchscreentouchscreen displays the word Valet while the driver profile
changes to Valet Mode on the touchscreen.
You can also use the mobile app to start and cancel Valet mode (if CybertruckModel SModel XModel 3Model Y is in Park).
When using the mobile app, you do not need to enter a PIN because you are already required to log into the app using your
Tesla Account credentials.
NOTE: If PIN to Drive is enabled (see PIN to Drive on page 658), you must enter the driving PIN before you can define or enter
a Valet PIN. Once in Valet mode, CybertruckModel SModel XModel 3Model Y can be driven without the valet needing to enter
the driving PIN.
NOTE: The PIN to Drive setting is not available when Valet mode is active.
If you forget your valet PIN, reset it from inside CybertruckModel SModel XModel 3Model Y by entering your Tesla Account
credentials (which also cancels Valet mode). You can also reset your PIN using the mobile app.
WARNING: Do not use Valet mode when towing a trailer. The torque limitations of Valet mode can make it difficult for
CybertruckModel SModel XModel 3Model Y to pull a trailer up a hill.
WARNING: Do not use Valet mode when towing a trailer. The torque limitations of Valet mode can make it difficult for
CybertruckModel SModel XModel 3Model Y to pull a trailer up a hill.
WARNING: Do not use Valet mode when towing a trailer. The torque limitations of Valet mode can make it difficult for
CybertruckModel SModel XModel 3Model Y to pull a trailer up a hill.
Canceling Valet Mode

With CybertruckModel SModel XModel 3Model Y in Park, touch the Valet Mode driver profile icon at the top of the
touchscreenControls screenControls screen, and enter your 4-digit PIN.

Owner's Manual

517

Owners Manual
When you cancel Valet mode, all settings associated with the most recently used driver profile and climate control settings are
restored, and all features are available.
NOTE: You do not need to enter a PIN to cancel Valet mode from the mobile app.

518

Owner's Manual

Owners Manual
Active Hood
How Active Hood Works
(If equipped) CybertruckModel SModel XModel 3Model Y (depending on market region and date of manufacture) (depending
on market region and date of manufacture) features a pedestrian protection system with an Active Hood that is designed to
reduce head injuries to pedestrians and cyclists in a frontal collision. Multiple sensors at the front of the vehicle are designed
to detect an impact with a pedestrian when CybertruckModel SModel XModel 3Model Y is moving between approximately 19
and 52 km/h28 and 52 km/h25 and 50 km/h23 and 52 km/h30 and 52 km/h, and raise the rear portion of the hood
automatically approximately 80 mm. This increases the space between the hood and the components beneath it, reducing the
likelihood of injuries.
NOTE: The pedestrian protection system relies on a series of sensors and algorithms designed and calibrated to determine
when Active Hood should deploy. Therefore, not all pedestrian collisions result in deployment. Similarly, the Active Hood may
deploy if CybertruckModel SModel XModel 3Model Y collides with an animal, vehicle, or other object.

Owner's Manual

519

Owners Manual